SBAS988 November   2023 ADC34RF55

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics - Power Consumption
    6. 5.6  Electrical Characteristics - DC Specifications
    7. 5.7  Electrical Characteristics - AC Specifications (Dither DISABLED)
    8. 5.8  Electrical Characteristics - AC Specifications (Dither ENABLED)
    9. 5.9  Timing Requirements
    10. 5.10 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Analog Inputs
        1. 6.3.1.1 Input Bandwidth and Full-Scale
        2. 6.3.1.2 Input Imbalance
        3. 6.3.1.3 Over Range Indication
        4. 6.3.1.4 Analog out-of-band dither
      2. 6.3.2 Sampling Clock Input
      3. 6.3.3 ADC Foreground Calibration
        1. 6.3.3.1 Calibration Control
        2. 6.3.3.2 ADC Switch
        3. 6.3.3.3 Calibration Configuration
      4. 6.3.4 SYSREF
        1. 6.3.4.1 SYSREF Capture Detection
      5. 6.3.5 Decimation Filter
        1. 6.3.5.1 Decimation Filter Response
        2. 6.3.5.2 Decimation Filter Configuration
        3. 6.3.5.3 20-bit Output Mode
        4. 6.3.5.4 Numerically Controlled Oscillator (NCO)
        5. 6.3.5.5 NCO Frequency Programming Using the SPI Interface
        6. 6.3.5.6 Fast Frequency Hopping
          1. 6.3.5.6.1 Fast frequency hopping using the GPIO1/2 pins
          2. 6.3.5.6.2 Fast frequency hopping using GPIO1/2, SEN and SDATA pins
          3. 6.3.5.6.3 Fast frequency hopping using the fast SPI
      6. 6.3.6 JESD204B Interface
        1. 6.3.6.1 JESD204B Initial Lane Alignment (ILA)
          1. 6.3.6.1.1 SYNC Signal
        2. 6.3.6.2 JESD204B Frame Assembly
          1. 6.3.6.2.1 JESD204B Frame Assembly in Bypass Mode
          2. 6.3.6.2.2 JESD204B Frame Assembly with Real Decimation - Single Band
          3. 6.3.6.2.3 JESD204B Frame Assembly with Complex Decimation - Single Band
          4. 6.3.6.2.4 JESD204B Frame Assembly with Decimation - Dual Band
        3. 6.3.6.3 SERDES Output MUX
      7. 6.3.7 Test Pattern
        1. 6.3.7.1 Transport Layer
        2. 6.3.7.2 Link Layer
        3. 6.3.7.3 Internal Capture Memory Buffer
    4. 6.4 Device Functional Modes
      1. 6.4.1 Bypass Mode
      2. 6.4.2 Digital Averaging
    5. 6.5 Programming
      1. 6.5.1 GPIO Pin Control
      2. 6.5.2 Configuration using the SPI interface
        1. 6.5.2.1 Register Write
        2. 6.5.2.2 Register Read
    6. 6.6 Register Maps
      1. 6.6.1 Detailed Register Description
  8. 7 Application Information Disclaimer
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Wideband RF Sampling Receiver
      2. 7.2.2 Design Requirements
        1. 7.2.2.1 Input Signal Path
        2. 7.2.2.2 Clocking
      3. 7.2.3 Detailed Design Procedure
        1. 7.2.3.1 Sampling Clock
      4. 7.2.4 Application Curves
    3. 7.3 Initialization Set Up
      1. 7.3.1 Initial Device Configuration After Power-Up
        1. 7.3.1.1  STEP 1: RESET
        2. 7.3.1.2  STEP 2: Device Configuration
        3. 7.3.1.3  STEP 3: JESD Interface Configuration (1)
        4. 7.3.1.4  STEP 4: SYSREF Synchronization
        5. 7.3.1.5  STEP 5: JESD Interface Configuration (2)
        6. 7.3.1.6  STEP 6: Analog Trim Settings
        7. 7.3.1.7  STEP 7: Calibration Configuration
        8. 7.3.1.8  STEP 8: SYSREF Synchronization
        9. 7.3.1.9  STEP 9: Run Power up Calibration
        10. 7.3.1.10 Step 10: JESD Interface Synchronization
        11. 7.3.1.11 Step 11: NCO Configuration
    4. 7.4 Power Supply Recommendations
    5. 7.5 Layout
      1. 7.5.1 Layout Guidelines
      2. 7.5.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Third-Party Products Disclaimer
    2. 8.2 Receiving Notification of Documentation Updates
    3. 8.3 Support Resources
    4. 8.4 Trademarks
    5. 8.5 Electrostatic Discharge Caution
    6. 8.6 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.3.3.3 Calibration Configuration

The ADC34RF55 provides 3 different options to configure the internal foreground calibration:

  • Calibrate all ADCs one time using SPI trigger (after initial power up or during operation) - see Table 6-8
  • Continuous calibration - see Table 6-9
  • Calibrate 2 ADCs at a time using GPIO trigger - see Table 6-10

The status of the calibration can be read back from register 0x298 (CALIBRATION page). Successful calibration reads back 0x0E on the 4 LSB of that register.

Table 6-8 Register Writes for power up calibration or SINGLE calibration of all ADCs Using SPI
ADDRDATADESCRIPTION
0x050x20Select CALIBRATION page
0x460x02
0x450x8AToggle calibration start
0x450x0A
wait1.3 seconds x 3 GSPS / FS
Table 6-9 Register Writes to Trigger CONTINOUS Calibration of all ADCs Using SPI
ADDRDATADESCRIPTION
0x050x20Select CALIBRATION page
0x460x03
0x450x0A
Table 6-10 Register Writes to Trigger ADC Pair Calibration Using the GPIO Pin
ADDRDATADESCRIPTION
0x050x20Select CALIBRATION page
0x460x02
0x450x4A
0x050x02Select DIGITAL page
0x2340x04Use GPIO1 pin to freeze calibration switch