SBAS988 November   2023 ADC34RF55

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics - Power Consumption
    6. 5.6  Electrical Characteristics - DC Specifications
    7. 5.7  Electrical Characteristics - AC Specifications (Dither DISABLED)
    8. 5.8  Electrical Characteristics - AC Specifications (Dither ENABLED)
    9. 5.9  Timing Requirements
    10. 5.10 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Analog Inputs
        1. 6.3.1.1 Input Bandwidth and Full-Scale
        2. 6.3.1.2 Input Imbalance
        3. 6.3.1.3 Over Range Indication
        4. 6.3.1.4 Analog out-of-band dither
      2. 6.3.2 Sampling Clock Input
      3. 6.3.3 ADC Foreground Calibration
        1. 6.3.3.1 Calibration Control
        2. 6.3.3.2 ADC Switch
        3. 6.3.3.3 Calibration Configuration
      4. 6.3.4 SYSREF
        1. 6.3.4.1 SYSREF Capture Detection
      5. 6.3.5 Decimation Filter
        1. 6.3.5.1 Decimation Filter Response
        2. 6.3.5.2 Decimation Filter Configuration
        3. 6.3.5.3 20-bit Output Mode
        4. 6.3.5.4 Numerically Controlled Oscillator (NCO)
        5. 6.3.5.5 NCO Frequency Programming Using the SPI Interface
        6. 6.3.5.6 Fast Frequency Hopping
          1. 6.3.5.6.1 Fast frequency hopping using the GPIO1/2 pins
          2. 6.3.5.6.2 Fast frequency hopping using GPIO1/2, SEN and SDATA pins
          3. 6.3.5.6.3 Fast frequency hopping using the fast SPI
      6. 6.3.6 JESD204B Interface
        1. 6.3.6.1 JESD204B Initial Lane Alignment (ILA)
          1. 6.3.6.1.1 SYNC Signal
        2. 6.3.6.2 JESD204B Frame Assembly
          1. 6.3.6.2.1 JESD204B Frame Assembly in Bypass Mode
          2. 6.3.6.2.2 JESD204B Frame Assembly with Real Decimation - Single Band
          3. 6.3.6.2.3 JESD204B Frame Assembly with Complex Decimation - Single Band
          4. 6.3.6.2.4 JESD204B Frame Assembly with Decimation - Dual Band
        3. 6.3.6.3 SERDES Output MUX
      7. 6.3.7 Test Pattern
        1. 6.3.7.1 Transport Layer
        2. 6.3.7.2 Link Layer
        3. 6.3.7.3 Internal Capture Memory Buffer
    4. 6.4 Device Functional Modes
      1. 6.4.1 Bypass Mode
      2. 6.4.2 Digital Averaging
    5. 6.5 Programming
      1. 6.5.1 GPIO Pin Control
      2. 6.5.2 Configuration using the SPI interface
        1. 6.5.2.1 Register Write
        2. 6.5.2.2 Register Read
    6. 6.6 Register Maps
      1. 6.6.1 Detailed Register Description
  8. 7 Application Information Disclaimer
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Wideband RF Sampling Receiver
      2. 7.2.2 Design Requirements
        1. 7.2.2.1 Input Signal Path
        2. 7.2.2.2 Clocking
      3. 7.2.3 Detailed Design Procedure
        1. 7.2.3.1 Sampling Clock
      4. 7.2.4 Application Curves
    3. 7.3 Initialization Set Up
      1. 7.3.1 Initial Device Configuration After Power-Up
        1. 7.3.1.1  STEP 1: RESET
        2. 7.3.1.2  STEP 2: Device Configuration
        3. 7.3.1.3  STEP 3: JESD Interface Configuration (1)
        4. 7.3.1.4  STEP 4: SYSREF Synchronization
        5. 7.3.1.5  STEP 5: JESD Interface Configuration (2)
        6. 7.3.1.6  STEP 6: Analog Trim Settings
        7. 7.3.1.7  STEP 7: Calibration Configuration
        8. 7.3.1.8  STEP 8: SYSREF Synchronization
        9. 7.3.1.9  STEP 9: Run Power up Calibration
        10. 7.3.1.10 Step 10: JESD Interface Synchronization
        11. 7.3.1.11 Step 11: NCO Configuration
    4. 7.4 Power Supply Recommendations
    5. 7.5 Layout
      1. 7.5.1 Layout Guidelines
      2. 7.5.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Third-Party Products Disclaimer
    2. 8.2 Receiving Notification of Documentation Updates
    3. 8.3 Support Resources
    4. 8.4 Trademarks
    5. 8.5 Electrostatic Discharge Caution
    6. 8.6 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information
6.3.5.6.3 Fast frequency hopping using the fast SPI

In this mode, the GPIO1/2 pins are used as a fast SPI input which only updates the NCO selection registers. No register address information needs to be sent. GPIO1 pin is SDATA and GPIO2 pin is SCLK.

This mode is enabled by setting the SPISEL to logic high and using the following register writes:

  1. Set 0x234 to 0x43 (NCO SEL MODE = 2, GPIO MODE = 3)

The NCO frequencies are selected as shown in Table 6-27.

Table 6-27 NCO Frequency Programming using FAST SPI
NO. OF BANDSD15D14D13D12D11D10D9D8D7D6D5D4D3D2D1D0
SINGLENCO1 CHD [2]0NCO1 CHD [1:0]NCO1 CHC [2]0NCO1 CHC [1:0]NCO1 CHB [2]0NCO1 CHB [1:0]NCO1 CHA [2]0NCO1 CHA [1:0]
DUALNCO2 CHD [1:0]NCO1 CHD [1:0]NCO2 CHC [1:0]NCO1 CHC [1:0]NCO2 CHB [1:0]NCO1 CHB [1:0]NCO2 CHA [1:0]NCO1 CHA [1:0]