SBASA56
September 2023
AMC131M02
PRODUCTION DATA
1
1
Features
2
Applications
3
Description
4
Revision History
5
Pin Configuration and Functions
6
Specifications
6.1
Absolute Maximum Ratings
6.2
ESD Ratings
6.3
Recommended Operating Conditions
6.4
Thermal Information
6.5
Insulation Specifications
6.6
Safety-Related Certifications
6.7
Safety Limiting Values
6.8
Electrical Characteristics
6.9
Timing Requirements
6.10
Switching Characteristics
6.11
Timing Diagrams
6.12
Typical Characteristics
7
Parameter Measurement Information
7.1
Noise Measurements
8
Detailed Description
8.1
Overview
8.2
Functional Block Diagram
8.3
Feature Description
8.3.1
Isolated DC/DC Converter
8.3.1.1
DC/DC Converter Failure Detection
8.3.2
High-Side Current Drive Capability
8.3.3
Isolation Channel Signal Transmission
8.3.4
Input ESD Protection Circuitry
8.3.5
Input Multiplexer
8.3.6
Programmable Gain Amplifier (PGA)
8.3.7
Voltage Reference
8.3.8
Internal Test Signals
8.3.9
Clocking and Power Modes
8.3.10
ΔΣ Modulator
8.3.11
Digital Filter
8.3.11.1
Digital Filter Implementation
8.3.11.1.1
Fast-Settling Filter
8.3.11.1.2
SINC3 and SINC3 + SINC1 Filter
8.3.11.2
Digital Filter Characteristic
8.3.12
Channel Phase Calibration
8.3.13
Calibration Registers
8.3.14
Register Map CRC
8.3.15
General-Purpose Digital Output (GPO)
8.4
Device Functional Modes
8.4.1
Power-Up and Reset
8.4.1.1
Power-On Reset
8.4.1.2
SYNC/RESET Pin
8.4.1.3
RESET Command
8.4.2
Start-Up Behavior After Power-Up
8.4.3
Start-Up Behavior After a Pin Reset or RESET Command
8.4.4
Start-Up Behavior After a Pause in CLKIN
8.4.5
Synchronization
8.4.6
Conversion Modes
8.4.6.1
Continuous-Conversion Mode
8.4.6.2
Global-Chop Mode
8.4.7
Power Modes
8.4.8
Standby Mode
8.5
Programming
8.5.1
Serial Interface
8.5.1.1
Chip Select (CS)
8.5.1.2
Serial Data Clock (SCLK)
8.5.1.3
Serial Data Input (DIN)
8.5.1.4
Serial Data Output (DOUT)
8.5.1.5
Data Ready (DRDY)
8.5.1.6
Conversion Synchronization or System Reset (SYNC/RESET)
8.5.1.7
SPI Communication Frames
8.5.1.8
SPI Communication Words
8.5.1.9
Short SPI Frames
8.5.1.10
Communication Cyclic Redundancy Check (CRC)
8.5.1.11
SPI Timeout
8.5.2
ADC Conversion Data
8.5.3
Commands
8.5.3.1
NULL (0000 0000 0000 0000)
8.5.3.2
RESET (0000 0000 0001 0001)
8.5.3.3
STANDBY (0000 0000 0010 0010)
8.5.3.4
WAKEUP (0000 0000 0011 0011)
8.5.3.5
LOCK (0000 0101 0101 0101)
8.5.3.6
UNLOCK (0000 0110 0101 0101)
8.5.3.7
RREG (101a aaaa annn nnnn)
8.5.3.7.1
Reading a Single Register
8.5.3.7.2
Reading Multiple Registers
8.5.3.8
WREG (011a aaaa annn nnnn)
8.5.4
ADC Output Buffer and FIFO Buffer
8.5.5
Collecting Data for the First Time or After a Pause in Data Collection
8.6
AMC131M02 Registers
9
Application and Implementation
9.1
Application Information
9.1.1
Unused Inputs and Outputs
9.1.2
Antialiasing
9.1.3
Minimum Interface Connections
9.1.4
Multiple Device Configuration
9.1.5
Calibration
9.1.6
Troubleshooting
9.2
Typical Application
9.2.1
Design Requirements
9.2.2
Detailed Design Procedure
9.2.2.1
Voltage Measurement
9.2.2.2
Current Shunt Measurement
9.2.3
Application Curves
9.3
Power Supply Recommendations
9.4
Layout
9.4.1
Layout Guidelines
9.4.2
Layout Example
10
Device and Documentation Support
10.1
Documentation Support
10.1.1
Related Documentation
10.2
Receiving Notification of Documentation Updates
10.3
Support Resources
10.4
Trademarks
10.5
Electrostatic Discharge Caution
10.6
Glossary
11
Mechanical, Packaging, and Orderable Information
Package Options
Mechanical Data (Package|Pins)
DFM|20
MCSS009
Thermal pad, mechanical data (Package|Pins)
Orderable Information
sbasa56_oa
sbasa56_pm
10.6
Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.