SLUSAK9B September   2011  – April 2015

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  8. 8 Parameter Measurement Information
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Adapter Detect and ACOK Output
      2. 9.3.2  Adapter Overvoltage (ACOVP)
      3. 9.3.3  System Power Selection
      4. 9.3.4  Automatic Internal Soft-Start Charger Current
      5. 9.3.5  Converter Operation
      6. 9.3.6  Input Overcurrent Protection (ACOC)
      7. 9.3.7  Charge Overcurrent Protection (CHGOCP)
      8. 9.3.8  Battery Overvoltage Protection (BATOVP)
      9. 9.3.9  Battery Shorted to Ground (BATLOWV)
      10. 9.3.10 Thermal Shutdown Protection (TSHUT)
      11. 9.3.11 Inductor Short, MOSFET Short Protection
    4. 9.4 Device Functional Modes
      1. 9.4.1 Enable and Disable Charging
      2. 9.4.2 Continuous Conduction Mode (CCM)
      3. 9.4.3 Discontinuous Conduction Mode (DCM)
    5. 9.5 Programming
      1. 9.5.1 SMBus Interface
      2. 9.5.2 Battery LEARN Cycle
      3. 9.5.3 Charge Time-out
      4. 9.5.4 High-Accuracy Current-Sense Amplifier
      5. 9.5.5 EMI Switching Frequency Adjust
    6. 9.6 Register Maps
      1. 9.6.1 Battery-Charger Commands
      2. 9.6.2 Setting Charger Options
      3. 9.6.3 Charge Options Register [reset = 0x12H]
      4. 9.6.4 Setting the Charge Current
      5. 9.6.5 Setting the Charge Voltage
      6. 9.6.6 Setting Input Current
      7. 9.6.7 Support Turbo Boost Function
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Negative Output Voltage Protection
        2. 10.2.2.2 Reverse Input Voltage Protection
        3. 10.2.2.3 Reduce Battery Quiescent Current
        4. 10.2.2.4 Inductor Selection
        5. 10.2.2.5 Input Capacitor
        6. 10.2.2.6 Output Capacitor
        7. 10.2.2.7 Power MOSFETs Selection
        8. 10.2.2.8 Input Filter Design
        9. 10.2.2.9 bq24735 Design Guideline
      3. 10.2.3 Application Curves
    3. 10.3 System Examples
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Third-Party Products Disclaimer
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 Trademarks
    4. 13.4 Electrostatic Discharge Caution
    5. 13.5 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

11 Power Supply Recommendations

When adapter is attached, and ACOK goes HIGH, the system is connected to adapter through ACFET/RBFET. An external resistor voltage divider attenuates the adapter voltage before it goes to ACDET. The adapter detect threshold should typically be programmed to a value greater than the maximum battery voltage, but lower than the IC maximum allowed input voltage and system maximum allowed voltage.

When adapter is removed, the system is connected to battery through BATFET. Typically the battery depletion threshold should be greater than the minimum system voltage so that the battery capacity can be fully used for maximum battery life.