SLUSF18A October   2023  – December 2023 BQ25638

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Description (continued)
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Power-On-Reset (POR)
      2. 7.3.2  Device Power Up from Battery
      3. 7.3.3  Device Power Up from Input Source
        1. 7.3.3.1 REGN LDO Power Up
        2. 7.3.3.2 Poor Source Qualification
        3. 7.3.3.3 Input Voltage Limit Threshold Setting (VINDPM Threshold)
        4. 7.3.3.4 Converter Power-Up
        5. 7.3.3.5 Input Current Optimizer (ICO)
        6. 7.3.3.6 Switching Frequency and Dithering Feature
      4. 7.3.4  Power Path Management
        1. 7.3.4.1 Narrow VDC Architecture
        2. 7.3.4.2 Dynamic Power Management
          1. 7.3.4.2.1 Input Current Limit on ILIM Pin
        3. 7.3.4.3 High Impedance (HIZ) Mode
      5. 7.3.5  Battery Charging Management
        1. 7.3.5.1 Autonomous Charging Cycle
        2. 7.3.5.2 Battery Charging Profile
        3. 7.3.5.3 Charging Termination
        4. 7.3.5.4 Thermistor Qualification
          1. 7.3.5.4.1 Advanced Temperature Profile in Charge Mode
          2. 7.3.5.4.2 TS Pin Thermistor Configuration
          3. 7.3.5.4.3 Cold/Hot Temperature Window in OTG Mode
          4. 7.3.5.4.4 JEITA Charge Rate Scaling
          5. 7.3.5.4.5 TS_BIAS Pin
        5. 7.3.5.5 Charging Safety Timers
      6. 7.3.6  USB On-The-Go (OTG)
        1. 7.3.6.1 Boost OTG Mode
      7. 7.3.7  Integrated 12-bit ADC for Monitoring
      8. 7.3.8  Status Outputs (INT , PG , STAT)
        1. 7.3.8.1 PG Pin Power Good Indicator
        2. 7.3.8.2 Charging Status Indicator (STAT)
        3. 7.3.8.3 Interrupt to Host (INT)
      9. 7.3.9  BATFET Control
        1. 7.3.9.1 Shutdown Mode
        2. 7.3.9.2 Ultra-Low Power Mode
        3. 7.3.9.3 System Power Reset
      10. 7.3.10 Protections
        1. 7.3.10.1 Voltage and Current Monitoring in Battery Only and HIZ Modes
          1. 7.3.10.1.1 Battery Overcurrent Protection
          2. 7.3.10.1.2 Battery Undervoltage Lockout
        2. 7.3.10.2 Voltage and Current Monitoring in Forward Mode
          1. 7.3.10.2.1 Input Overvoltage
          2. 7.3.10.2.2 System Overvoltage Protection (SYSOVP)
          3. 7.3.10.2.3 Forward Converter Cycle-by-Cycle Current Limit
          4. 7.3.10.2.4 System Short
          5. 7.3.10.2.5 Battery Overvoltage Protection (BATOVP)
          6. 7.3.10.2.6 Sleep and Poor Source Comparators
        3. 7.3.10.3 Voltage and Current Monitoring in Reverse Mode
          1. 7.3.10.3.1 Boost Mode Overvoltage Protection
          2. 7.3.10.3.2 Boost Mode Duty Cycle Protection
          3. 7.3.10.3.3 Boost Mode PMID Undervoltage Protection
          4. 7.3.10.3.4 Boost Mode Battery Undervoltage
          5. 7.3.10.3.5 Boost Converter Cycle-by-Cycle Current Limit
          6. 7.3.10.3.6 Boost Mode SYS Short
        4. 7.3.10.4 Thermal Regulation and Thermal Shutdown
          1. 7.3.10.4.1 Thermal Protection in Buck Mode
          2. 7.3.10.4.2 Thermal Protection in Boost Mode
          3. 7.3.10.4.3 Thermal Protection in Battery-only Mode
    4. 7.4 Device Functional Modes
      1. 7.4.1 Host Mode and Default Mode
      2. 7.4.2 Register Bit Reset
    5. 7.5 Programming
      1. 7.5.1 Serial Interface
        1. 7.5.1.1 Data Validity
        2. 7.5.1.2 START and STOP Conditions
        3. 7.5.1.3 Byte Format
        4. 7.5.1.4 Acknowledge (ACK) and Not Acknowledge (NACK)
        5. 7.5.1.5 Target Address and Data Direction Bit
        6. 7.5.1.6 Single Write and Read
        7. 7.5.1.7 Multi-Write and Multi-Read
    6. 7.6 BQ25638 Registers
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Inductor Selection
        2. 8.2.2.2 Input Capacitor
        3. 8.2.2.3 Output Capacitor
      3. 8.2.3 Application Curves
  10. 9 Power Supply Recommendations
  11. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 Support Resources
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • YBG|30
Thermal pad, mechanical data (Package|Pins)
Orderable Information

1 Features

  • High-efficiency 5-A, 1.5-MHz, synchronous switch mode buck charger for single cell battery
    • >90% efficiency down to 10-mA output current from 5-V input
    • Charge current up to 5 A in 80-mA steps
    • Charge termination from 30 to 1000 mA in 10-mA steps
    • Flexible JEITA profile for safe charging over temperature
  • BATFET control to support shutdown and full system reset
    • 1.5-μA quiescent current in battery only mode
    • 1.3-μA battery leakage current in ultra-low power mode
    • 100-nA battery leakage current in shutdown
  • Supports USB On-The-Go (OTG)
    • Boost mode operation with 3.84-V to 9.6-V output
    • Programmable current limit up to 3.2 A
  • Supports a wide range of input sources
    • 3.9-V to 18-V wide input operating voltage range with 26-V absolute maximum input voltage
    • VINDPM threshold automatically tracks battery voltage
    • Input Current Optimizer (ICO) to maximize input power without overloading adapters
  • Efficient battery operation with 7-mΩ BATFET
  • Narrow VDC (NVDC) power path management
    • System instant-on with depleted or no battery
    • Battery supplement when adapter is fully loaded
  • Flexible autonomous or I2C-controlled modes
  • Integrated 12-bit ADC for voltage, current, and temperature monitoring
    • ADCIN pin for external signal up-to 1 V
  • High accuracy
    • ±0.5% charge voltage regulation
    • ±5% charge current regulation
    • ±5% input current regulation
  • Safety
    • Battery temperature sensing
    • Thermal regulation and thermal shutdown
    • Battery/converter overcurrent protection
    • Charging safety timer