SLUSD20B july   2018  – april 2023 BQ25710

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Power-Up from Battery Without DC Source
      2. 9.3.2  Vmin Active Protection (VAP) when Battery only Mode
      3. 9.3.3  Power-Up From DC Source
        1. 9.3.3.1 CHRG_OK Indicator
        2. 9.3.3.2 Input Voltage and Current Limit Setup
        3. 9.3.3.3 Battery Cell Configuration
        4. 9.3.3.4 Device Hi-Z State
      4. 9.3.4  USB On-The-Go (OTG)
      5. 9.3.5  Converter Operation
        1. 9.3.5.1 Inductance Detection Through IADPT Pin
        2. 9.3.5.2 Continuous Conduction Mode (CCM)
        3. 9.3.5.3 Pulse Frequency Modulation (PFM)
      6. 9.3.6  Current and Power Monitor
        1. 9.3.6.1 High-Accuracy Current Sense Amplifier (IADPT and IBAT)
        2. 9.3.6.2 High-Accuracy Power Sense Amplifier (PSYS)
      7. 9.3.7  Input Source Dynamic Power Manage
      8. 9.3.8  Two-Level Adapter Current Limit (Peak Power Mode)
      9. 9.3.9  Processor Hot Indication
        1. 9.3.9.1 PROCHOT During Low Power Mode
        2. 9.3.9.2 PROCHOT Status
      10. 9.3.10 Device Protection
        1. 9.3.10.1 Watchdog Timer
        2. 9.3.10.2 Input Overvoltage Protection (ACOV)
        3. 9.3.10.3 Input Overcurrent Protection (ACOC)
        4. 9.3.10.4 System Overvoltage Protection (SYSOVP)
        5. 9.3.10.5 Battery Overvoltage Protection (BATOVP)
        6. 9.3.10.6 Battery Short
        7. 9.3.10.7 System Short Hiccup Mode
        8. 9.3.10.8 Thermal Shutdown (TSHUT)
    4. 9.4 Device Functional Modes
      1. 9.4.1 Forward Mode
        1. 9.4.1.1 System Voltage Regulation with Narrow VDC Architecture
        2. 9.4.1.2 Battery Charging
      2. 9.4.2 USB On-The-Go
      3. 9.4.3 Pass Through Mode (PTM)
    5. 9.5 Programming
      1. 9.5.1 SMBus Interface
        1. 9.5.1.1 SMBus Write-Word and Read-Word Protocols
        2. 9.5.1.2 Timing Diagrams
    6. 9.6 Register Map
      1. 9.6.1  Setting Charge and PROCHOT Options
        1. 9.6.1.1 ChargeOption0 Register (SMBus address = 12h) [reset = E70Eh]
        2. 9.6.1.2 ChargeOption1 Register (SMBus address = 30h) [reset = 0211h]
        3. 9.6.1.3 ChargeOption2 Register (SMBus address = 31h) [reset = 02B7h]
        4. 9.6.1.4 ChargeOption3 Register (SMBus address = 32h) [reset = 0030h]
        5. 9.6.1.5 ProchotOption0 Register (SMBus address = 33h) [reset = 4A65h]
        6. 9.6.1.6 ProchotOption1 Register (SMBus address = 34h) [reset = 81A0h]
        7. 9.6.1.7 ADCOption Register (SMBus address = 35h) [reset = 2000h]
      2. 9.6.2  Charge and PROCHOT Status
        1. 9.6.2.1 ChargerStatus Register (SMBus address = 20h) [reset = 0000h]
        2. 9.6.2.2 ProchotStatus Register (SMBus address = 21h) [reset = A800h]
      3. 9.6.3  ChargeCurrent Register (SMBus address = 14h) [reset = 0000h]
        1. 9.6.3.1 Battery Precharge Current Clamp
      4. 9.6.4  MaxChargeVoltage Register (SMBus address = 15h) [reset value based on CELL_BATPRESZ pin setting]
      5. 9.6.5  MinSystemVoltage Register (SMBus address = 3Eh) [reset value based on CELL_BATPRESZ pin setting]
        1. 9.6.5.1 System Voltage Regulation
      6. 9.6.6  Input Current and Input Voltage Registers for Dynamic Power Management
        1. 9.6.6.1 Input Current Registers
          1. 9.6.6.1.1 IIN_HOST Register With 10-mΩ Sense Resistor (SMBus address = 3Fh) [reset = 4100h]
          2. 9.6.6.1.2 IIN_DPM Register With 10-mΩ Sense Resistor (SMBus address = 022h) [reset = 4100h]
          3. 9.6.6.1.3 InputVoltage Register (SMBus address = 3Dh) [reset = VBUS-1.28V]
      7. 9.6.7  OTGVoltage Register (SMBus address = 3Bh) [reset = 0000h]
      8. 9.6.8  OTGCurrent Register (SMBus address = 3Ch) [reset = 0000h]
      9. 9.6.9  ADCVBUS/PSYS Register (SMBus address = 23h)
      10. 9.6.10 ADCIBAT Register (SMBus address = 24h)
      11. 9.6.11 ADCIINCMPIN Register (SMBus address = 25h)
      12. 9.6.12 ADCVSYSVBAT Register (SMBus address = 26h)
      13. 9.6.13 ID Registers
        1. 9.6.13.1 ManufactureID Register (SMBus address = FEh) [reset = 0040h]
        2. 9.6.13.2 Device ID (DeviceAddress) Register (SMBus address = FFh) [reset = 0h]
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 ACP-ACN Input Filter
        2. 10.2.2.2 Inductor Selection
        3. 10.2.2.3 Input Capacitor
        4. 10.2.2.4 Output Capacitor
        5. 10.2.2.5 Power MOSFETs Selection
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
      1. 12.2.1 Layout Example Reference Top View
      2. 12.2.2 Inner Layer Layout and Routing Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Third-Party Products Disclaimer
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 Receiving Notification of Documentation Updates
    4. 13.4 Support Resources
    5. 13.5 Trademarks
    6. 13.6 Electrostatic Discharge Caution
    7. 13.7 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.6.1.4 ChargeOption3 Register (SMBus address = 32h) [reset = 0030h]

Figure 9-9 ChargeOption3 Register (SMBus address = 32h) [reset = 0030h]
15141312111098
EN_HIZRESET_REGRESET_
VINDPM		EN_OTG
EN_ICO
MODE		Reserved
R/WR/WR/WR/WR/WR/W
76543210
ReservedEN_CONS
VAP		OTG_VAP
_MODE		IL_AVGOTG_RANGE
_LOW		BATFETOFF_
HIZ		PSYS_OTG_
IDCHG
R/WR/WR/WR/WR/WR/WR/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 9-13 ChargeOption3 Register (SMBus address = 32h) Field Descriptions
SMBus
BIT		FIELDTYPERESETDESCRIPTION
15EN_HIZR/W0b

Device Hi-Z Mode Enable

When the charger is in Hi-Z mode, the device draws minimal quiescent current. With VBUS above UVLO. REGN LDO stays on, and system powers from battery.

0b: Device not in Hi-Z mode <default at POR>

1b: Device in Hi-Z mode

14RESET_REGR/W0b

Reset Registers

All the registers go back to the default setting except the VINDPM

register.

0b: Idle <default at POR>

1b: Reset all the registers to default values. After reset, this bit goes back to 0.

13RESET_VINDPMR/W0b

Reset VINDPM Threshold

0b: Idle

1b: Converter is disabled to measure VINDPM threshold. After VINDPM measurement is done, this bit goes back to 0 and converter starts.

12EN_OTGR/W0b

OTG Mode Enable

Enable device in OTG mode when EN_OTG pin is HIGH.

0b: Disable OTG <default at POR>

1b: Enable OTG mode to supply VBUS from battery.

11EN_ICO_MODER/W0b

Enable ICO Algorithm

0b: Disable ICO algorithm. <default at POR>

1b: Enable ICO algorithm.

10-8ReservedR/W000b

Reserved

Table 9-14 ChargeOption3 Register (SMBus address = 32h) Field Descriptions
SMBus
BIT		FIELDTYPERESETDESCRIPTION
7ReservedR/W0bReserved
6EN_CON_VAPR/W0b

Enable the conservative VAP mode.

0b: Disabled <default at POR>

1b: Enabled

5OTG_VAP_MODER/W1b

The selection of the external OTG/VAP pin control.

0b: the external OTG/VAP pin controls the EN/DIS VAP mode

1b: the external OTG/VAP pin controls the EN/DIS OTG mode <default at POR>

4-3IL_AVGR/W10b

4 levels inductor average current clamp.

00b: 6A

01b: 10A

10b: 15A <default at POR>

11b: Disabled

2OTG_RANGE_LOWR/W0b

Selection of the different OTG ouput voltage range.

0b: VOTG high range 4.28 V - 20.8 V <default at POR>

1b: VOTG low range 3 V - 19.52 V

1BATFETOFF_
HIZ		R/W0b

Control BATFET during HIZ mode.

0b: BATFET on during Hi-Z <default at POR>

1b: BATFET off during Hi-Z

0PSYS_OTG_
IDCHG		R/W0b

PSYS function during OTG mode.

0b: PSYS as battery discharge power minus OTG output power <default at POR>

1b: PSYS as battery discharge power only