SLUSD20B july   2018  – april 2023 BQ25710

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Power-Up from Battery Without DC Source
      2. 9.3.2  Vmin Active Protection (VAP) when Battery only Mode
      3. 9.3.3  Power-Up From DC Source
        1. 9.3.3.1 CHRG_OK Indicator
        2. 9.3.3.2 Input Voltage and Current Limit Setup
        3. 9.3.3.3 Battery Cell Configuration
        4. 9.3.3.4 Device Hi-Z State
      4. 9.3.4  USB On-The-Go (OTG)
      5. 9.3.5  Converter Operation
        1. 9.3.5.1 Inductance Detection Through IADPT Pin
        2. 9.3.5.2 Continuous Conduction Mode (CCM)
        3. 9.3.5.3 Pulse Frequency Modulation (PFM)
      6. 9.3.6  Current and Power Monitor
        1. 9.3.6.1 High-Accuracy Current Sense Amplifier (IADPT and IBAT)
        2. 9.3.6.2 High-Accuracy Power Sense Amplifier (PSYS)
      7. 9.3.7  Input Source Dynamic Power Manage
      8. 9.3.8  Two-Level Adapter Current Limit (Peak Power Mode)
      9. 9.3.9  Processor Hot Indication
        1. 9.3.9.1 PROCHOT During Low Power Mode
        2. 9.3.9.2 PROCHOT Status
      10. 9.3.10 Device Protection
        1. 9.3.10.1 Watchdog Timer
        2. 9.3.10.2 Input Overvoltage Protection (ACOV)
        3. 9.3.10.3 Input Overcurrent Protection (ACOC)
        4. 9.3.10.4 System Overvoltage Protection (SYSOVP)
        5. 9.3.10.5 Battery Overvoltage Protection (BATOVP)
        6. 9.3.10.6 Battery Short
        7. 9.3.10.7 System Short Hiccup Mode
        8. 9.3.10.8 Thermal Shutdown (TSHUT)
    4. 9.4 Device Functional Modes
      1. 9.4.1 Forward Mode
        1. 9.4.1.1 System Voltage Regulation with Narrow VDC Architecture
        2. 9.4.1.2 Battery Charging
      2. 9.4.2 USB On-The-Go
      3. 9.4.3 Pass Through Mode (PTM)
    5. 9.5 Programming
      1. 9.5.1 SMBus Interface
        1. 9.5.1.1 SMBus Write-Word and Read-Word Protocols
        2. 9.5.1.2 Timing Diagrams
    6. 9.6 Register Map
      1. 9.6.1  Setting Charge and PROCHOT Options
        1. 9.6.1.1 ChargeOption0 Register (SMBus address = 12h) [reset = E70Eh]
        2. 9.6.1.2 ChargeOption1 Register (SMBus address = 30h) [reset = 0211h]
        3. 9.6.1.3 ChargeOption2 Register (SMBus address = 31h) [reset = 02B7h]
        4. 9.6.1.4 ChargeOption3 Register (SMBus address = 32h) [reset = 0030h]
        5. 9.6.1.5 ProchotOption0 Register (SMBus address = 33h) [reset = 4A65h]
        6. 9.6.1.6 ProchotOption1 Register (SMBus address = 34h) [reset = 81A0h]
        7. 9.6.1.7 ADCOption Register (SMBus address = 35h) [reset = 2000h]
      2. 9.6.2  Charge and PROCHOT Status
        1. 9.6.2.1 ChargerStatus Register (SMBus address = 20h) [reset = 0000h]
        2. 9.6.2.2 ProchotStatus Register (SMBus address = 21h) [reset = A800h]
      3. 9.6.3  ChargeCurrent Register (SMBus address = 14h) [reset = 0000h]
        1. 9.6.3.1 Battery Precharge Current Clamp
      4. 9.6.4  MaxChargeVoltage Register (SMBus address = 15h) [reset value based on CELL_BATPRESZ pin setting]
      5. 9.6.5  MinSystemVoltage Register (SMBus address = 3Eh) [reset value based on CELL_BATPRESZ pin setting]
        1. 9.6.5.1 System Voltage Regulation
      6. 9.6.6  Input Current and Input Voltage Registers for Dynamic Power Management
        1. 9.6.6.1 Input Current Registers
          1. 9.6.6.1.1 IIN_HOST Register With 10-mΩ Sense Resistor (SMBus address = 3Fh) [reset = 4100h]
          2. 9.6.6.1.2 IIN_DPM Register With 10-mΩ Sense Resistor (SMBus address = 022h) [reset = 4100h]
          3. 9.6.6.1.3 InputVoltage Register (SMBus address = 3Dh) [reset = VBUS-1.28V]
      7. 9.6.7  OTGVoltage Register (SMBus address = 3Bh) [reset = 0000h]
      8. 9.6.8  OTGCurrent Register (SMBus address = 3Ch) [reset = 0000h]
      9. 9.6.9  ADCVBUS/PSYS Register (SMBus address = 23h)
      10. 9.6.10 ADCIBAT Register (SMBus address = 24h)
      11. 9.6.11 ADCIINCMPIN Register (SMBus address = 25h)
      12. 9.6.12 ADCVSYSVBAT Register (SMBus address = 26h)
      13. 9.6.13 ID Registers
        1. 9.6.13.1 ManufactureID Register (SMBus address = FEh) [reset = 0040h]
        2. 9.6.13.2 Device ID (DeviceAddress) Register (SMBus address = FFh) [reset = 0h]
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 ACP-ACN Input Filter
        2. 10.2.2.2 Inductor Selection
        3. 10.2.2.3 Input Capacitor
        4. 10.2.2.4 Output Capacitor
        5. 10.2.2.5 Power MOSFETs Selection
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
      1. 12.2.1 Layout Example Reference Top View
      2. 12.2.2 Inner Layer Layout and Routing Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Third-Party Products Disclaimer
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 Receiving Notification of Documentation Updates
    4. 13.4 Support Resources
    5. 13.5 Trademarks
    6. 13.6 Electrostatic Discharge Caution
    7. 13.7 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.5.1 SMBus Interface

The BQ25710 device operates as a slave, receiving control inputs from the embedded controller host through the SMBus interface. The BQ25710 device uses a simplified subset of the commands documented in System Management Bus Specification V1.1, which can be downloaded from www.smbus.org. The BQ25710 device uses the SMBus read-word and write-word protocols (shown in Table 9-4 and Table 9-5) to communicate with the smart battery. The device performs only as a SMBus slave device with address 0b00010010 (0x12H) and does not initiate communication on the bus. In addition, the device has two identification registers, a 16-bit device ID register (0xFFH) and a 16-bit manufacturer ID register (0xFEH).

SMBus communication starts when VCC is above V(UVLO).

The data (SDA) and clock (SCL) pins have Schmitt-trigger inputs that can accommodate slow edges. Choose pullup resistors (10 kΩ) for SDA and SCL to achieve rise times according to the SMBus specifications. Communication starts when the master signals a start condition, which is a high-to-low transition on SDA, while SCL is high. When the master has finished communicating, the master issues a stop condition, which is a low-to-high transition on SDA, while SCL is high. The bus is then free for another transmission. Figure 9-4 and Figure 9-5 show the timing diagram for signals on the SMBus interface. The address byte, command byte, and data bytes are transmitted between the start and stop conditions. The SDA state changes only while SCL is low, except for the start and stop conditions. Data is transmitted in 8-bit bytes and is sampled on the rising edge of SCL. Nine clock cycles are required to transfer each byte in or out of the device because either the master or the slave acknowledges the receipt of the correct byte during the ninth clock cycle. The BQ25710 supports the charger commands listed in Table 9-4.