SLUSFF9 November   2023 BQ27Z558

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Description (continued)
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Supply Current
    6. 6.6  Internal 1.8-V LDO (REG18)
    7. 6.7  I/O (PULS, INT)
    8. 6.8  Chip Enable (CE)
    9. 6.9  Internal Temperature Sensor
    10. 6.10 NTC Thermistor Measurement Support
    11. 6.11 Coulomb Counter (CC)
    12. 6.12 Analog Digital Converter (ADC)
    13. 6.13 Internal Oscillator Specifications
    14. 6.14 Voltage Reference1 (REF1)
    15. 6.15 Voltage Reference2 (REF2)
    16. 6.16 Flash Memory
    17. 6.17 I2C I/O
    18. 6.18 I2C Timing — 100 kHz
    19. 6.19 I2C Timing — 400 kHz
    20. 6.20 HDQ Timing
    21. 6.21 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  BQ27Z558 Processor
      2. 7.3.2  Battery Parameter Measurements
        1. 7.3.2.1 Coulomb Counter (CC)
        2. 7.3.2.2 CC Digital Filter
        3. 7.3.2.3 ADC Multiplexer
        4. 7.3.2.4 Analog-to-Digital Converter (ADC)
        5. 7.3.2.5 Internal Temperature Sensor
        6. 7.3.2.6 External Temperature Sensor Support
      3. 7.3.3  Power Supply Control
      4. 7.3.4  Bus Communication Interface
      5. 7.3.5  Low Frequency Oscillator
      6. 7.3.6  High Frequency Oscillator
      7. 7.3.7  1.8-V Low Dropout Regulator
      8. 7.3.8  Internal Voltage References
      9. 7.3.9  Gas Gauging
      10. 7.3.10 Charge Control Features
      11. 7.3.11 Authentication
    4. 7.4 Device Functional Modes
      1. 7.4.1 Lifetime Logging Features
      2. 7.4.2 Configuration
        1. 7.4.2.1 Coulomb Counting
        2. 7.4.2.2 Cell Voltage Measurements
        3. 7.4.2.3 Auto Calibration
        4. 7.4.2.4 Temperature Measurements
  9. 8 Applications and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Design Requirements (Default)
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Changing Design Parameters
      3. 8.2.3 Calibration Process
      4. 8.2.4 Gauging Data Updates
        1. 8.2.4.1 Application Curve
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Third-Party Products Disclaimer
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.2.2.1 Changing Design Parameters

For the firmware settings needed for the design requirements, refer to the BQ27Z558 Technical Reference Manual.

  • To change design capacity, set the data flash value (in mAh) in the Gas Gauging: Design: Design Capacity register.
  • To set device chemistry, go to the data flash I2C Configuration: Data: Device Chemistry. The bqStudio software automatically populates the correct chemistry identification. This selection is derived from using the BQCHEM feature in the tools and choosing the option that matches the device chemistry from the list.
  • To set the design voltage, go to Gas Gauging: Design: Design Voltage register.
  • To set the Cell Low Voltage or clear the Cell Low Voltage, use Settings: Configuration: Init Voltage Low Set or Clear. This is used to set the cell voltage level that will set (clear) the [VOLT_LO] bit in the Interrupt Status register.
  • To enable the internal temperature and the external temperature sensors: Set Settings:Configuration: Temperature Enable: Bit 0 (TSInt) = 1 for the internal sensor; set Bit 1 (TS1) = 1 for the external sensor.