SLUSDW2A November   2021  – February 2022 BQ27Z746

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configurations and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
      1. 6.5.1 Supply Current
      2. 6.5.2 Common Analog (LDO, LFO, HFO, REF1, REF2, I-WAKE)
      3. 6.5.3 Battery Protection (CHG, DSG)
      4. 6.5.4 Cell Sensing Output (BAT_SP, BAT_SN)
      5. 6.5.5 Gauge Measurements (ADC, CC, Temperature)
      6. 6.5.6 Flash Memory
    6. 6.6 Digital I/O: DC Characteristics
    7. 6.7 Digital I/O: Timing Characteristics
    8. 6.8 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  BQ27Z746 Processor
      2. 7.3.2  Battery Parameter Measurements
        1. 7.3.2.1 Coulomb Counter (CC) and Digital Filter
        2. 7.3.2.2 ADC Multiplexer
        3. 7.3.2.3 Analog-to-Digital Converter (ADC)
        4. 7.3.2.4 Internal Temperature Sensor
        5. 7.3.2.5 External Temperature Sensor Support
      3. 7.3.3  Power Supply Control
      4. 7.3.4  Bus Communication Interface
      5. 7.3.5  Low Frequency Oscillator
      6. 7.3.6  High Frequency Oscillator
      7. 7.3.7  1.8-V Low Dropout Regulator
      8. 7.3.8  Internal Voltage References
      9. 7.3.9  Overcurrent in Discharge Protection
      10. 7.3.10 Overcurrent in Charge Protection
      11. 7.3.11 Short-Circuit Current in Discharge Protection
      12. 7.3.12 Primary Protection Features
      13. 7.3.13 Battery Sensing
      14. 7.3.14 Gas Gauging
      15. 7.3.15 Zero Volt Charging (ZVCHG)
      16. 7.3.16 Charge Control Features
      17. 7.3.17 Authentication
    4. 7.4 Device Functional Modes
      1. 7.4.1 Lifetime Logging Features
      2. 7.4.2 Configuration
        1. 7.4.2.1 Coulomb Counting
        2. 7.4.2.2 Cell Voltage Measurements
        3. 7.4.2.3 Auto Calibration
        4. 7.4.2.4 Temperature Measurements
  8. 8 Applications and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Design Requirements (Default)
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Changing Design Parameters
      3. 8.2.3 Calibration Process
      4. 8.2.4 Gauging Data Updates
        1. 8.2.4.1 Application Curve
  9. 9 Power Supply Requirements
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Third-Party Products Disclaimer
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 Support Resources
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  12. 12Mechanical, Orderable, and Packaging Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • YAH|15
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.3.11 Short-Circuit Current in Discharge Protection

The short-circuit current in discharge (SCD) function detects catastrophic current conditions in the discharge direction. The short-circuit in discharge thresholds and delay times are configurable through the firmware register. The thresholds and timing can be fine-tuned even further based on a sense resistor with lower resistance or wider tolerance with calibration. The detection circuit also incorporates a delay before disabling the CHG and DSG FETs. When an SCD event occurs, the Safety Status flag bit is set to 1 and is latched until it is cleared and the fault condition is removed.