SLUSEE3 July   2021 BQ51013B-Q1

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Details of a Qi Wireless Power System and BQ51013B-Q1 Power Transfer Flow Diagrams
      2. 9.3.2  Dynamic Rectifier Control
      3. 9.3.3  Dynamic Efficiency Scaling
      4. 9.3.4  RILIM Calculations
      5. 9.3.5  Input Overvoltage
      6. 9.3.6  Adapter Enable Functionality and EN1/EN2 Control
      7. 9.3.7  End Power Transfer Packet (WPC Header 0x02)
      8. 9.3.8  Status Outputs
      9. 9.3.9  WPC Communication Scheme
      10. 9.3.10 Communication Modulator
      11. 9.3.11 Adaptive Communication Limit
      12. 9.3.12 Synchronous Rectification
      13. 9.3.13 Temperature Sense Resistor Network (TS)
      14. 9.3.14 3-State Driver Recommendations for the TS/CTRL Pin
      15. 9.3.15 Thermal Protection
      16. 9.3.16 WPC v1.2 Compliance – Foreign Object Detection
      17. 9.3.17 Receiver Coil Load-Line Analysis
    4. 9.4 Device Functional Modes
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Applications
      1. 10.2.1 BQ51013B-Q1 Wireless Power Receiver Used as a Power Supply
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
          1. 10.2.1.2.1 Using The BQ51013B-Q1 as a Wireless Power Supply: (See Figure 1-1 )
          2. 10.2.1.2.2 Series and Parallel Resonant Capacitor Selection
          3. 10.2.1.2.3 Recommended RX Coils
          4. 10.2.1.2.4 COMM, CLAMP, and BOOT Capacitors
          5. 10.2.1.2.5 Control Pins and CHG
          6. 10.2.1.2.6 Current Limit and FOD
          7. 10.2.1.2.7 RECT and OUT Capacitance
        3. 10.2.1.3 Application Curves
      2. 10.2.2 Dual Power Path: Wireless Power and DC Input
        1. 10.2.2.1 Design Requirements
        2. 10.2.2.2 Detailed Design Procedure
        3. 10.2.2.3 Application Curves
      3. 10.2.3 Wireless and Direct Charging of a Li-Ion Battery at 800 mA
        1. 10.2.3.1 Design Requirements
        2. 10.2.3.2 Detailed Design Procedure
        3. 10.2.3.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Third-Party Products Disclaimer
      2. 13.1.2 Development Support
    2. 13.2 Receiving Notification of Documentation Updates
    3. 13.3 Support Resources
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.1 Overview

A wireless system consists of a charging pad (transmitter, TX or primary) and the secondary-side equipment (receiver, RX or secondary). There is a coil in the charging pad and in the secondary equipment which are magnetically coupled to each other when the secondary is placed on the primary. Power is then transferred from the transmitter to the receiver through coupled inductors (effectively an air-core transformer). Controlling the amount of power transferred is achieved by sending feedback (error signal) communication to the primary (to increase or decrease power).

The receiver communicates with the transmitter by changing the load seen by the transmitter. This load variation results in a change in the transmitter coil current, which is measured and interpreted by a processor in the charging pad. The communication is digital; packets are transferred from the receiver to the transmitter. Differential bi-phase encoding is used for the packets. The bit rate is 2-kbps.

Various types of communication packets have been defined. These include identification and authentication packets, error packets, control packets, end power packets, and power usage packets.

The transmitter coil stays powered off most of the time. It occasionally wakes up to see if a receiver is present. When a receiver authenticates itself to the transmitter, the transmitter will remain powered on. The receiver maintains full control over the power transfer using communication packets.

GUID-20210706-CA0I-TKNV-XTTD-VZHZDTTNL26N-low.gif Figure 9-1 WPC Wireless Power System Indicating the Functional Integration of the BQ51013B-Q1