SLUSDT5B September   2019  – October 2023 BQ75614-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Description (continued)
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Power Supplies
        1. 8.3.1.1 AVAO_REF and AVDD_REF
        2. 8.3.1.2 LDOIN
        3. 8.3.1.3 AVDD
        4. 8.3.1.4 DVDD
        5. 8.3.1.5 CVDD and NEG5V
        6. 8.3.1.6 TSREF
      2. 8.3.2 Measurement System
        1. 8.3.2.1 Main ADC
          1. 8.3.2.1.1 Cell Voltage Measurements
            1. 8.3.2.1.1.1 Analog Front End
            2. 8.3.2.1.1.2 VC Channel Measurements
            3. 8.3.2.1.1.3 Post-ADC Digital LPF
            4. 8.3.2.1.1.4 SRP and SRN Measurements
          2. 8.3.2.1.2 Temperature Measurements
            1. 8.3.2.1.2.1 DieTemp1 Measurement
            2. 8.3.2.1.2.2 GPIOs and TSREF Measurements
          3. 8.3.2.1.3 Main ADC Operation Control
            1. 8.3.2.1.3.1 Operation Modes and Status
        2. 8.3.2.2 AUX ADC
          1. 8.3.2.2.1 AUX Cell Voltage Measurements
            1. 8.3.2.2.1.1 AUX Analog Front End
            2. 8.3.2.2.1.2 CB and Current Sense Channel Measurements
          2. 8.3.2.2.2 AUX Temperature Measurements
            1. 8.3.2.2.2.1 DieTemp2 Measurement
            2. 8.3.2.2.2.2 AUX GPIO Measurements
          3. 8.3.2.2.3 MISC Measurements
          4. 8.3.2.2.4 AUX ADC Operation Control
        3. 8.3.2.3 Synchronization between MAIN and AUX ADC Measurements
        4. 8.3.2.4 CS ADC
      3. 8.3.3 Cell Balancing
        1. 8.3.3.1 Set Up Cell Balancing
          1. 8.3.3.1.1 Step 1: Determine Balancing Channels
          2. 8.3.3.1.2 Step 2: Select Balancing Control Methods
          3. 8.3.3.1.3 Step 3a: Balancing Thermal Management
          4. 8.3.3.1.4 Step 3b: Option to Stop On Cell Voltage Threshold
          5. 8.3.3.1.5 Step 3c: Option to Stop at Fault
        2. 8.3.3.2 Cell Balancing in SLEEP Mode
        3. 8.3.3.3 Pause and Stop Cell Balancing
          1. 8.3.3.3.1 Cell Balancing Pause
          2. 8.3.3.3.2 Cell Balancing Stop
          3. 8.3.3.3.3 Remaining CB Time
      4. 8.3.4 Integrated Hardware Protectors
        1. 8.3.4.1 OVUV Protectors
          1. 8.3.4.1.1 OVUV Operation Modes
          2. 8.3.4.1.2 OVUV Control and Status
            1. 8.3.4.1.2.1 OVUV Control
            2. 8.3.4.1.2.2 OVUV Status
        2. 8.3.4.2 OTUT Protector
          1. 8.3.4.2.1 OTUT Operation Modes
          2. 8.3.4.2.2 OTUT Control and Status
            1. 8.3.4.2.2.1 OTUT Control
            2. 8.3.4.2.2.2 OTUT Status
      5. 8.3.5 GPIO Configuration
      6. 8.3.6 Communication, OTP, Diagnostic Control
        1. 8.3.6.1 Communication
          1. 8.3.6.1.1 Serial Interface
            1. 8.3.6.1.1.1 UART Physical Layer
              1. 8.3.6.1.1.1.1 UART Transmitter
              2. 8.3.6.1.1.1.2 UART Receiver
              3. 8.3.6.1.1.1.3 COMM CLEAR
            2. 8.3.6.1.1.2 Command and Response Protocol
              1. 8.3.6.1.1.2.1 Transaction Frame Structure
                1. 8.3.6.1.1.2.1.1 Frame Initialization Byte
                2. 8.3.6.1.1.2.1.2 Device Address Byte
                3. 8.3.6.1.1.2.1.3 Register Address Bytes
                4. 8.3.6.1.1.2.1.4 Data Bytes
                5. 8.3.6.1.1.2.1.5 CRC Bytes
                6. 8.3.6.1.1.2.1.6 Calculating Frame CRC Value
                7. 8.3.6.1.1.2.1.7 Verifying Frame CRC
              2. 8.3.6.1.1.2.2 Transaction Frame Examples
                1. 8.3.6.1.1.2.2.1 Single Device Read/Write
          2. 8.3.6.1.2 Communication Timeout
            1. 8.3.6.1.2.1 Short Communication Timeout
            2. 8.3.6.1.2.2 Long Communication Timeout
          3. 8.3.6.1.3 SPI Master
          4. 8.3.6.1.4 SPI Loopback
        2. 8.3.6.2 Fault Handling
          1. 8.3.6.2.1 Fault Status Hierarchy
            1. 8.3.6.2.1.1 Debug Registers
          2. 8.3.6.2.2 Fault Masking and Reset
            1. 8.3.6.2.2.1 Fault Masking
            2. 8.3.6.2.2.2 Fault Reset
          3. 8.3.6.2.3 Fault Signaling
        3. 8.3.6.3 Nonvolatile Memory
          1. 8.3.6.3.1 OTP Page Status
          2. 8.3.6.3.2 OTP Programming
        4. 8.3.6.4 Diagnostic Control/Status
          1. 8.3.6.4.1 Power Supplies Check
            1. 8.3.6.4.1.1 Power Supply Diagnostic Check
            2. 8.3.6.4.1.2 Power Supply BIST
          2. 8.3.6.4.2 Thermal Shutdown and Warning Check
            1. 8.3.6.4.2.1 Thermal Shutdown
            2. 8.3.6.4.2.2 Thermal Warning
          3. 8.3.6.4.3 Oscillators Watchdog
          4. 8.3.6.4.4 OTP Error Check
            1. 8.3.6.4.4.1 OTP CRC Test and Faults
            2. 8.3.6.4.4.2 OTP Margin Read
            3. 8.3.6.4.4.3 Error Check and Correct (ECC) OTP
          5. 8.3.6.4.5 Integrated Hardware Protector Check
            1. 8.3.6.4.5.1 Parity Check
            2. 8.3.6.4.5.2 OVUV and OTUT DAC Check
            3. 8.3.6.4.5.3 OVUV Protector BIST
            4. 8.3.6.4.5.4 OTUT Protector BIST
          6. 8.3.6.4.6 Diagnostic Through ADC Comparison
            1. 8.3.6.4.6.1 Cell Voltage Measurement Check
            2. 8.3.6.4.6.2 Temperature Measurement Check
            3. 8.3.6.4.6.3 Cell Balancing FETs Check
            4. 8.3.6.4.6.4 VC and CB Open Wire Check
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power Modes
        1. 8.4.1.1 SHUTDOWN Mode
          1. 8.4.1.1.1 Exit SHUTDOWN Mode
          2. 8.4.1.1.2 Enter SHUTDOWN Mode
        2. 8.4.1.2 SLEEP Mode
          1. 8.4.1.2.1 Exit SLEEP Mode
          2. 8.4.1.2.2 Enter SLEEP Mode
        3. 8.4.1.3 ACTIVE Mode
          1. 8.4.1.3.1 Exit ACTIVE Mode
          2. 8.4.1.3.2 Enter ACTIVE Mode From SHUTDOWN Mode
          3. 8.4.1.3.3 Enter ACTIVE Mode From SLEEP Mode
      2. 8.4.2 Device Reset
      3. 8.4.3 Ping
        1. 8.4.3.1 Ping
    5. 8.5 Register Maps
      1. 8.5.1 OTP Shadow Register Summary
      2. 8.5.2 Read/Write Register Summary
      3. 8.5.3 Read-Only Register Summary
      4. 8.5.4 Register Field Descriptions
        1. 8.5.4.1  Device Addressing Setup
          1. 8.5.4.1.1 DIR0_ADDR_OTP
          2. 8.5.4.1.2 DIR1_ADDR_OTP
          3. 8.5.4.1.3 CUST_MISC1 through CUST_MISC8
          4. 8.5.4.1.4 DIR0_ADDR
          5. 8.5.4.1.5 DIR1_ADDR
        2. 8.5.4.2  Device ID and Scratch Pad
          1. 8.5.4.2.1 PARTID
          2. 8.5.4.2.2 DEV_REVID
          3. 8.5.4.2.3 DIE_ID1 through DIE_ID9
        3. 8.5.4.3  General Configuration and Control
          1. 8.5.4.3.1  DEV_CONF
          2. 8.5.4.3.2  ACTIVE_CELL
          3. 8.5.4.3.3  PWR_TRANSIT_CONF
          4. 8.5.4.3.4  COMM_TIMEOUT_CONF
          5. 8.5.4.3.5  TX_HOLD_OFF
          6. 8.5.4.3.6  COMM_CTRL
          7. 8.5.4.3.7  CONTROL1
          8. 8.5.4.3.8  CONTROL2
          9. 8.5.4.3.9  CUST_CRC_HI
          10. 8.5.4.3.10 CUST_CRC_LO
          11. 8.5.4.3.11 CUST_CRC_RSLT_HI
          12. 8.5.4.3.12 CUST_CRC_RSLT_LO
        4. 8.5.4.4  Operation Status
          1. 8.5.4.4.1 DIAG_STAT
          2. 8.5.4.4.2 ADC_STAT1
          3. 8.5.4.4.3 ADC_STAT2
          4. 8.5.4.4.4 GPIO_STAT
          5. 8.5.4.4.5 BAL_STAT
          6. 8.5.4.4.6 DEV_STAT
        5. 8.5.4.5  ADC Configuration and Control
          1. 8.5.4.5.1  ADC_CONF1
          2. 8.5.4.5.2  ADC_CONF2
          3. 8.5.4.5.3  MAIN_ADC_CAL1
          4. 8.5.4.5.4  MAIN_ADC_CAL2
          5. 8.5.4.5.5  AUX_ADC_CAL1
          6. 8.5.4.5.6  AUX_ADC_CAL2
          7. 8.5.4.5.7  CS_ADC_CAL1
          8. 8.5.4.5.8  CS_ADC_CAL2
          9. 8.5.4.5.9  ADC_CTRL1
          10. 8.5.4.5.10 ADC_CTRL2
          11. 8.5.4.5.11 ADC_CTRL3
        6. 8.5.4.6  ADC Measurement Results
          1. 8.5.4.6.1  VCELL16_HI/LO
          2. 8.5.4.6.2  VCELL15_HI/LO
          3. 8.5.4.6.3  VCELL14_HI/LO
          4. 8.5.4.6.4  VCELL13_HI/LO
          5. 8.5.4.6.5  VCELL12_HI/LO
          6. 8.5.4.6.6  VCELL11_HI/LO
          7. 8.5.4.6.7  VCELL10_HI/LO
          8. 8.5.4.6.8  VCELL9_HI/LO
          9. 8.5.4.6.9  VCELL8_HI/LO
          10. 8.5.4.6.10 VCELL7_HI/LO
          11. 8.5.4.6.11 VCELL6_HI/LO
          12. 8.5.4.6.12 VCELL5_HI/LO
          13. 8.5.4.6.13 VCELL4_HI/LO
          14. 8.5.4.6.14 VCELL3_HI/LO
          15. 8.5.4.6.15 VCELL2_HI/LO
          16. 8.5.4.6.16 VCELL1_HI/LO
          17. 8.5.4.6.17 MAIN_CURRENT_HI/LO
          18. 8.5.4.6.18 CURRENT_HI/MID/LO
          19. 8.5.4.6.19 TSREF_HI/LO
          20. 8.5.4.6.20 GPIO1_HI/LO
          21. 8.5.4.6.21 GPIO2_HI/LO
          22. 8.5.4.6.22 GPIO3_HI/LO
          23. 8.5.4.6.23 GPIO4_HI/LO
          24. 8.5.4.6.24 GPIO5_HI/LO
          25. 8.5.4.6.25 GPIO6_HI/LO
          26. 8.5.4.6.26 GPIO7_HI/LO
          27. 8.5.4.6.27 GPIO8_HI/LO
          28. 8.5.4.6.28 DIETEMP1_HI/LO
          29. 8.5.4.6.29 DIETEMP2_HI/LO
          30. 8.5.4.6.30 AUX_CELL_HI/LO
          31. 8.5.4.6.31 AUX_GPIO_HI/LO
          32. 8.5.4.6.32 AUX_BAT_HI/LO
          33. 8.5.4.6.33 AUX_REFL_HI/LO
          34. 8.5.4.6.34 AUX_VBG2_HI/LO
          35. 8.5.4.6.35 AUX_AVAO_REF_HI/LO
          36. 8.5.4.6.36 AUX_AVDD_REF_HI/LO
          37. 8.5.4.6.37 AUX_OV_DAC_HI/LO
          38. 8.5.4.6.38 AUX_UV_DAC_HI/LO
          39. 8.5.4.6.39 AUX_OT_OTCB_DAC_HI/LO
          40. 8.5.4.6.40 AUX_UT_DAC_HI/LO
          41. 8.5.4.6.41 AUX_VCBDONE_DAC_HI/LO
          42. 8.5.4.6.42 AUX_VCM_HI/LO
          43. 8.5.4.6.43 REFOVDAC_HI/LO
          44. 8.5.4.6.44 DIAG_MAIN_HI/LO
          45. 8.5.4.6.45 DIAG_AUX_HI/LO
        7. 8.5.4.7  Balancing Configuration, Control and Status
          1. 8.5.4.7.1 CB_CELL16_CTRL through CB_CELL1_CTRL
          2. 8.5.4.7.2 VCB_DONE_THRESH
          3. 8.5.4.7.3 OTCB_THRESH
          4. 8.5.4.7.4 BAL_CTRL1
          5. 8.5.4.7.5 BAL_CTRL2
          6. 8.5.4.7.6 BAL_CTRL3
          7. 8.5.4.7.7 CB_COMPLETE1
          8. 8.5.4.7.8 CB_COMPLETE2
          9. 8.5.4.7.9 BAL_TIME
        8. 8.5.4.8  Protector Configuration and Control
          1. 8.5.4.8.1 OV_THRESH
          2. 8.5.4.8.2 UV_THRESH
          3. 8.5.4.8.3 UV_DISABLE1
          4. 8.5.4.8.4 UV_DISABLE2
          5. 8.5.4.8.5 OTUT_THRESH
          6. 8.5.4.8.6 OVUV_CTRL
          7. 8.5.4.8.7 OTUT_CTRL
        9. 8.5.4.9  GPIO Configuration
          1. 8.5.4.9.1 GPIO_CONF1
          2. 8.5.4.9.2 GPIO_CONF2
          3. 8.5.4.9.3 GPIO_CONF3
          4. 8.5.4.9.4 GPIO_CONF4
        10. 8.5.4.10 SPI Master
          1. 8.5.4.10.1 SPI_CONF
          2. 8.5.4.10.2 SPI_EXE
          3. 8.5.4.10.3 SPI_TX3, SPI_TX2, and SPI_TX1
          4. 8.5.4.10.4 SPI_RX3, SPI_RX2, and SPI_RX1
        11. 8.5.4.11 Diagnostic Control
          1. 8.5.4.11.1  DIAG_OTP_CTRL
          2. 8.5.4.11.2  DIAG_COMM_CTRL
          3. 8.5.4.11.3  DIAG_PWR_CTRL
          4. 8.5.4.11.4  DIAG_CBFET_CTRL1
          5. 8.5.4.11.5  DIAG_CBFET_CTRL2
          6. 8.5.4.11.6  DIAG_COMP_CTRL1
          7. 8.5.4.11.7  DIAG_COMP_CTRL2
          8. 8.5.4.11.8  DIAG_COMP_CTRL3
          9. 8.5.4.11.9  DIAG_COMP_CTRL4
          10. 8.5.4.11.10 DIAG_PROT_CTRL
        12. 8.5.4.12 Fault Configuration and Reset
          1. 8.5.4.12.1 FAULT_MSK1
          2. 8.5.4.12.2 FAULT_MSK2
          3. 8.5.4.12.3 FAULT_RST1
          4. 8.5.4.12.4 FAULT_RST2
        13. 8.5.4.13 Fault Status
          1. 8.5.4.13.1  FAULT_SUMMARY
          2. 8.5.4.13.2  FAULT_COMM1
          3. 8.5.4.13.3  FAULT_OTP
          4. 8.5.4.13.4  FAULT_SYS
          5. 8.5.4.13.5  FAULT_PROT1
          6. 8.5.4.13.6  FAULT_PROT2
          7. 8.5.4.13.7  FAULT_OV1
          8. 8.5.4.13.8  FAULT_OV2
          9. 8.5.4.13.9  FAULT_UV1
          10. 8.5.4.13.10 FAULT_UV2
          11. 8.5.4.13.11 FAULT_OT
          12. 8.5.4.13.12 FAULT_UT
          13. 8.5.4.13.13 FAULT_COMP_GPIO
          14. 8.5.4.13.14 FAULT_COMP_VCCB1
          15. 8.5.4.13.15 FAULT_COMP_VCCB2
          16. 8.5.4.13.16 FAULT_COMP_VCOW1
          17. 8.5.4.13.17 FAULT_COMP_VCOW2
          18. 8.5.4.13.18 FAULT_COMP_CBOW1
          19. 8.5.4.13.19 FAULT_COMP_CBOW2
          20. 8.5.4.13.20 FAULT_COMP_CBFET1
          21. 8.5.4.13.21 FAULT_COMP_CBFET2
          22. 8.5.4.13.22 FAULT_COMP_MISC
          23. 8.5.4.13.23 FAULT_PWR1
          24. 8.5.4.13.24 FAULT_PWR2
          25. 8.5.4.13.25 FAULT_PWR3
        14. 8.5.4.14 Debug Control and Status
          1. 8.5.4.14.1 DEBUG_UART_RC
          2. 8.5.4.14.2 DEBUG_UART_RR_TR
          3. 8.5.4.14.3 DEBUG_UART_DISCARD
          4. 8.5.4.14.4 DEBUG_UART_VALID_HI/LO
          5. 8.5.4.14.5 DEBUG_OTP_SEC_BLK
          6. 8.5.4.14.6 DEBUG_OTP_DED_BLK
        15. 8.5.4.15 OTP Programming Control and Status
          1. 8.5.4.15.1 OTP_PROG_UNLOCK1A through OTP_PROG_UNLOCK1D
          2. 8.5.4.15.2 OTP_PROG_UNLOCK2A through OTP_PROG_UNLOCK2D
          3. 8.5.4.15.3 OTP_PROG_CTRL
          4. 8.5.4.15.4 OTP_ECC_TEST
          5. 8.5.4.15.5 OTP_ECC_DATAIN1 through OTP_ECC_DATAIN9
          6. 8.5.4.15.6 OTP_ECC_DATAOUT1 through OTP_ECC_DATAOUT9
          7. 8.5.4.15.7 OTP_PROG_STAT
          8. 8.5.4.15.8 OTP_CUST1_STAT
          9. 8.5.4.15.9 OTP_CUST2_STAT
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Application Circuit
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Cell Sensing and Balancing Inputs
          2. 9.2.1.2.2 Synchronize Voltage and Current Measurements
          3. 9.2.1.2.3 BAT and External NPN
          4. 9.2.1.2.4 Power Supplies, Reference Input
          5. 9.2.1.2.5 GPIO For Thermistor Inputs
          6. 9.2.1.2.6 Internal Balancing Current
          7. 9.2.1.2.7 UART, NFAULT
          8. 9.2.1.2.8 Current Sense Input
        3. 9.2.1.3 Application Curve
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Ground Planes
      2. 11.1.2 Bypass Capacitors for Power Supplies and Reference
      3. 11.1.3 Cell Voltage Sensing
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Third-Party Products Disclaimer
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Support Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  14. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information
8.3.6.4.4.3 Error Check and Correct (ECC) OTP

ECC:

Register values for selected registers (0x0000 to 0x002F) are permanently stored in OTP. All registers also exist as volatile storage locations at the same addresses, referred to as shadow registers. The volatile registers are for reading, writing, and device control. For a list of registers included in the OTP, see Section 8.5.1.

During wakeup, the device first loads all shadow registers with hardware default values listed in Section 8.5.1. Then the device loads the registers conditionally with OTP contents from the results of the Error Check and Correct (ECC) evaluation of the OTP. The OTP is loaded to shadow registers in 64-bit blocks; each block has its own Error Check and Correct (ECC) value stored. The ECC detects a single-bit (Single-Error-Correction) or double-bit (Double-Error-Detection) changes in OTP stored data. The ECC is calculated for each block, individually.

Single-bit errors are corrected, double-bit errors are only detected, not corrected. A block with good ECC is loaded. A block with a single-bit error is corrected, and the FAULT_OTP[SEC_DET] bit is set to flag the corrected error event. Additionally, the DEBUG_OTP_SEC_BLK register is updated with the location of the error corrected block. This enables the host to keep track of potentially damaged memory. The block is loaded to shadow registers after the single-bit error correction. Because the evaluation is on a block-by-block basis, it is possible for multiple blocks to have a single-correctable error and still be loaded correctly. Multiple-bit errors can exist with full correction, as long as they are limited to a single error per block.

A block with a bad ECC comparison (two-bit errors in one block) is not loaded and the FAULT_OTP[DED_DET] bit is set to flag the failed bit-error event. Additionally, the DEBUG_OTP_DED_BLK register is updated with the block where the double error occurred. The hardware default value remains in the register. This allows some blocks to be loaded correctly (no fail or single-bit corrected value) and some blocks not to load. When the FAULT_OTP[SEC_DET] or FAULT_OTP[DED_DET] bit is set and the condition is not cleared by a device reset, the device is corrupted and must not be used.

The ECC engine uses the industry standard 72,64 SEC DEC ECC implementation. The OTP is protected by a (72, 64) Hamming code, providing single error correction, double error detection (SECDED). For each 64 bits of data stored in OTP, an additional 8 bits of parity information are stored. The parity bits are designated p0, p1, p2, p4, p8, p16, p32, and p64. Bit p0 covers the entire encoded 72-bit ECC block. The remaining seven parity bits are assigned according to the following rule:

  • Parity bit p1 covers odd bit positions, that is, bit positions which have the least significant bit of the bit position equal to 1 (1, 3, 5, and so on), including the p1 bit itself (bit 1).
  • Parity bit p2 covers bit positions which have the second least significant bit of the bit position equal to 1 (2, 3, 6, 7, 10, 11, and so on), including the p2 bit itself (bit 2).
  • The pattern continues for p4, p8, p16, p32, and p64. Table 8-22 specifies the complete encoding.

Table 8-22 (72, 64) Parity Encoding
Bit Position 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54
Encoded Bits d63 d62 d61 d60 d59 d58 d57 p64 d56 d55 d54 d53 d52 d51 d50 d49 d48 d47
Parity Bit Coverage p0 x x x x x x x x x x x x x x x x x x
p1 x x x x x x x x x
p2 x x x x x x x x x x
p4 x x x x x x x x x x
p8 x x x x x x x x
p16 x x x x x x x x x x
p32 x x x x x x x x x x
p64 x x x x x x x x
Bit Position 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36
Encoded Bits d46 d45 d44 d43 d42 d41 d40 d39 d38 d37 d36 d35 d34 d33 d32 d31 d30 d29
Parity Bit Coverage p0 x x x x x x x x x x x x x x x x x x
p1 x x x x x x x x x
p2 x x x x x x x x
p4 x x x x x x x x x x
p8 x x x x x x x x
p16 x x x x x x
p32 x x x x x x x x x x x x x x x x x x
p64
Bit Position 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18
Encoded Bits d28 d27 d26 p32 d25 d24 d23 d22 d21 d20 d19 d18 d17 d16 d15 d14 d13 d12
Parity Bit Coverage p0 x x x x x x x x x x x x x x x x x x
p1 x x x x x x x x x
p2 x x x x x x x x x x
p4 x x x x x x x x
p8 x x x x x x x x
p16 x x x x x x x x x x x x x x
p32 x x x x
p64
Bit Position 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Encoded Bits d11 p16 d10 d9 d8 d7 d6 d5 d4 p8 d36 d2 d1 p4 d0 p2 p1 p0
Parity Bit Coverage p0 x x x x x x x x x x x x x x x x x x
p1 x x x x x x x x x
p2 x x x x x x x x
p4 x x x x x x x x
p8 x x x x x x x x
p16 x x
p32
p64
Table 8-23 Encoder and Decoder Data IN and OUT Positioning
ENCODER
DATA IN Encoded Bits DATA OUT Bit Positions
OTP_ECC_DATAIN 1 d0 to d7 OTP_ECC_DATAOUT 1 0 to 7
OTP_ECC_DATAIN 2 d8 to d15 OTP_ECC_ DATAOUT 2 8 to 15
OTP_ECC_DATAIN 3 d16 to d23 OTP_ECC_ DATAOUT 3 16 to 23
OTP_ECC_DATAIN 4 d24 to d31 OTP_ECC_ DATAOUT 4 24 to 31
OTP_ECC_DATAIN 5 d32 to d39 OTP_ECC_ DATAOUT 5 32 to 39
OTP_ECC_DATAIN 6 d40 to d47 OTP_ECC_ DATAOUT 6 40 to 47
OTP_ECC_DATAIN 7 d48 to d55 OTP_ECC_ DATAOUT 7 48 to 55
OTP_ECC_DATAIN 8 d56 to d63 OTP_ECC_ DATAOUT 8 56 to 63
OTP_ECC_ DATAOUT 9 64 to 71
DECODER
DATA IN Bit Positions DATA IN Encoded Bits
OTP_ECC_DATAIN 1 0 to 7 OTP_ECC_DATAOUT 1 d0 to d7
OTP_ECC_DATAIN 2 8 to 15 OTP_ECC_ DATAOUT 2 d8 to d15
OTP_ECC_DATAIN 3 16 to 23 OTP_ECC_ DATAOUT 3 d16 to d23
OTP_ECC_DATAIN 4 24 to 31 OTP_ECC_ DATAOUT 4 d24 to d31
OTP_ECC_DATAIN 5 32 to 39 OTP_ECC_ DATAOUT 5 d32 to d39
OTP_ECC_DATAIN 6 40 to 47 OTP_ECC_ DATAOUT 6 d40 to d47
OTP_ECC_DATAIN 7 48 to 55 OTP_ECC_ DATAOUT 7 d48 to d55
OTP_ECC_DATAIN 8 56 to 63 OTP_ECC_ DATAOUT 8 d56 to d63
OTP_ECC_DATAIN 9 64 to 71

ECC Diagnostic Test: The device provides a diagnostic tool to test the ECC function. There are two modes that are available to run the diagnostic. The first, auto mode (OTP_ECC_TEST[MANUAL_AUTO] = 0), uses internal data to run the tests. In auto mode, the OTP_ECC_TEST[DED_SEC] bit selects the type of test that is to be performed and the OTP_ECC_TEST[ENC_DEC] bit determines if the encoder or decoder function is to be tested. The result of the ECC test is provided in the OTP_ECC_DATAOUT* registers within 1μs delay. The test steps and expected results from each test are shown below.

Automatic Decoding steps:

  1. Set ECC Test to automatic OTP_ECC_TEST[MANUAL_AUTO] = 0
  2. Set decoder setting OTP_ECC_TEST[ENC_DEC] = 0
  3. Set decoder to single or double encoding setting with OTP_ECC_TEST[DED_SEC] (1 for DED or 0 for SEC)
  4. Clear all SEC/DED faults by FAULT_RST2[RST_OTP_DATA] = 1
  5. Enable ECC test OTP_ECC_TEST[ENABLE] = 1
  6. Read FAULT_OTP[SEC_DET] flag for SEC or FAULT_OTP[DED_DET] flag for DED
  7. Block read OTP_ECC_DATAOUT1 to OTP_ECC_DATAOUT8 to verify the decoder test results as in Table 8-24
  8. Disable ECC test OTP_ECC_TEST[ENABLE] = 0

Automatic Encoding steps:

  1. Set ECC TEST to automatic OTP_ECC_TEST[MANUAL_AUTO] = 0
  2. Set the encoder setting using OTP_ECC_TEST[ENC_DEC] = 1
  3. Enable the ECC test with OTP_ECC_TEST[ENABLE] = 1
  4. Block read OTP_ECC_DATAOUT1 to OTP_ECC_DATAOUT9 to verify the encoder test results as in Table 8-24
  5. Disable ECC test OTP_ECC_TEST[ENABLE] = 0

Table 8-24 Decoder and Encoder Test Verification
[DED_SEC][ENC_DEC][SEC_DET][DED_DET]OTP_DATAOUT*
0 (SEC test)0 (Decoder test)100x18C3 FF8A 68A9 8069
0 (SEC test)1 (Encoder test)N/AN/A0xCD 3968 C140 2EA5 ED6D
1 (DED test)0 (Decoder test)010x0000 0000 0000 0000
1 (DED test)1 (Encoder test)N/AN/A0xCD 3968 C140 2EA5 ED6D