SWRS227C March   2020  – December 2024 CC3130

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Functional Block Diagram
  6. 5 Device Comparison
    1. 5.1 Related Products
  7. 6 Pin Configuration and Functions
    1. 6.1 Pin Diagram
    2. 6.2 Pin Attributes
    3. 6.3 Signal Descriptions
      1.      12
    4. 6.4 Connections for Unused Pins
  8. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Power-On Hours (POH)
    4. 7.4  Recommended Operating Conditions
    5. 7.5  Current Consumption Summary
    6. 7.6  TX Power Control
    7. 7.7  Brownout and Blackout Conditions
      1. 7.7.1 Brownout and Blackout Voltage Levels
    8. 7.8  Electrical Characteristics for DIO Pins
      1. 7.8.1 Electrical Characteristics: DIO Pins Except 52 and 53
      2. 7.8.2 Electrical Characteristics: DIO Pins 52 and 53
    9. 7.9  Electrical Characteristics for Pin Internal Pullup and Pulldown
    10. 7.10 WLAN Receiver Characteristics
      1.      28
    11. 7.11 WLAN Transmitter Characteristics
      1.      30
    12. 7.12 WLAN Transmitter Out-of-Band Emissions
      1. 7.12.1 WLAN 2.4GHz Filter Requirements
    13. 7.13 BLE/2.4GHz Radio Coexistence and WLAN Coexistence Requirements
    14. 7.14 Thermal Resistance Characteristics for RGK Package
    15. 7.15 Timing and Switching Characteristics
      1. 7.15.1 Power Supply Sequencing
      2. 7.15.2 Device Reset
      3. 7.15.3 Reset Timing
        1. 7.15.3.1 nRESET (32-kHz Crystal)
        2. 7.15.3.2 First-Time Power-Up and Reset Removal Timing Requirements (32kHz Crystal)
        3. 7.15.3.3 nRESET (External 32kHz Crystal)
          1. 7.15.3.3.1 First-Time Power-Up and Reset Removal Timing Requirements (External 32kHz Crystal)
      4. 7.15.4 Wakeup from HIBERNATE Mode
        1. 7.15.4.1 nHIB Timing Requirements
      5. 7.15.5 Clock Specifications
        1. 7.15.5.1 Slow Clock Using Internal Oscillator
          1. 7.15.5.1.1 RTC Crystal Requirements
        2. 7.15.5.2 Slow Clock Using an External Clock
          1. 7.15.5.2.1 External RTC Digital Clock Requirements
        3. 7.15.5.3 Fast Clock (Fref) Using an External Crystal
          1. 7.15.5.3.1 WLAN Fast-Clock Crystal Requirements
        4. 7.15.5.4 Fast Clock (Fref) Using an External Oscillator
          1. 7.15.5.4.1 External Fref Clock Requirements (–40°C to +85°C)
      6. 7.15.6 Interfaces
        1. 7.15.6.1 Host SPI Interface Timing
          1. 7.15.6.1.1 Host SPI Interface Timing Parameters
        2. 7.15.6.2 Flash SPI Interface Timing
          1. 7.15.6.2.1 Flash SPI Interface Timing Parameters
        3. 7.15.6.3 DIO Interface Timing
          1. 7.15.6.3.1 DIO Output Transition Time Parameters (Vsupply = 3.3V)
            1. 7.15.6.3.1.1 DIO Output Transition Times (Vsupply = 3.3V) #GUID-01C4FDBB-69B0-4F3E-AD14-CDACB1CFA3A4/SWAS03298470_
          2. 7.15.6.3.2 DIO Input Transition Time Parameters
            1. 7.15.6.3.2.1 DIO Input Transition Time Parameters
    16. 7.16 External Interfaces
      1. 7.16.1 SPI Flash Interface
      2. 7.16.2 SPI Host Interface
      3. 7.16.3 Host UART Interface
        1. 7.16.3.1 5-Wire UART Topology
        2. 7.16.3.2 4-Wire UART Topology
        3. 7.16.3.3 3-Wire UART Topology
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Device Features
      1. 8.2.1 WLAN
      2. 8.2.2 Network Stack
      3. 8.2.3 Security
      4. 8.2.4 Host Interface and Driver
      5. 8.2.5 System
    3. 8.3 Power-Management Subsystem
      1. 8.3.1 VBAT Wide-Voltage Connection
    4. 8.4 Low-Power Operating Modes
      1. 8.4.1 Low-Power Deep Sleep
      2. 8.4.2 Hibernate
      3. 8.4.3 Shutdown
    5. 8.5 Memory
      1. 8.5.1 External Memory Requirements
    6. 8.6 Restoring Factory Default Configuration
    7. 8.7 Hostless Mode
  10. 9 Applications, Implementation, and Layout
    1. 9.1 Application Information
      1. 9.1.1 BLE/2.4GHz Radio Coexistence
      2. 9.1.2 Antenna Selection
      3. 9.1.3 Typical Application
    2. 9.2 PCB Layout Guidelines
      1. 9.2.1 General PCB Guidelines
      2. 9.2.2 Power Layout and Routing
        1. 9.2.2.1 Design Considerations
      3. 9.2.3 Clock Interface Guidelines
      4. 9.2.4 Digital Input and Output Guidelines
      5. 9.2.5 RF Interface Guidelines
  11. 10Device and Documentation Support
    1. 10.1 Tools and Software
    2. 10.2 Firmware Updates
    3. 10.3 Device Nomenclature
    4. 10.4 Documentation Support
    5. 10.5 Trademarks
    6. 10.6 Electrostatic Discharge Caution
    7. 10.7 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Package Option Addendum
      1. 12.1.1 Packaging Information
      2. 12.1.2 Tape and Reel Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.1.2 Antenna Selection

The CC3130 device is designed to also support antenna selection and is controlled by Image Creator. When enabled, there are three options possible options:

  • ANT 1: When selected, the GPIOs that are defined for antenna selection with set the RF path for antenna 1.
  • ANT 2: When selected, the GPIOs that are defined for antenna selection will set the RF path for antenna 2.
  • Autoselect: When selected, during a scan and prior to connecting to an AP, the CC3130 device will determine the best RF path and select the appropriate antenna (5)(6). The result is saved as part of the profile.

Figure 9-3 shows the implementation of a complete Bluetooth® low energy and WLAN coexistence network with WLAN and antenna selection. The Coex switch is controlled by a GPIO signal from the BLE device and a GPIO signal from the CC3130 device. The antenna switch is controlled by two GPIO lines from the CC3130 device.

CC3130 Antenna Selection Solution With CoexistenceFigure 9-3 Antenna Selection Solution With Coexistence

Figure 9-4 shows the antenna selection implementation for Wi-Fi, with BLE operating on its own antenna. Note in this implementation no Coex switch is required and only a single GPIO from the BLE device to the CC3130 device is required. The antenna switch is controlled by two GPIO lines from the CC3130 device.

CC3130 Coexistence Solution With Wi-Fi Antenna Selection and Dedicated BLE AntennaFigure 9-4 Coexistence Solution With Wi-Fi Antenna Selection and Dedicated BLE Antenna
5. When selecting Autoselect via the API, a reset is required in order for the CC3230x device to determine the best antenna for use.