SNAS852 june   2023 CDCE6214Q1TM

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Description (cont.)
  7. 6 Device Comparison
  8. 7 Pin Configuration and Functions
  9. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Recommended Operating Conditions
    4. 8.4  Thermal Information
    5. 8.5  EEPROM Characteristics
    6. 8.6  Reference Input, Single-Ended Characteristics
    7. 8.7  Reference Input, Differential Characteristics
    8. 8.8  Reference Input, Crystal Mode Characteristics
    9. 8.9  General-Purpose Input Characteristics
    10. 8.10 Triple Level Input Characteristics
    11. 8.11 Logic Output Characteristics
    12. 8.12 Phase Locked Loop Characteristics
    13. 8.13 Closed-Loop Output Jitter Characteristics
    14. 8.14 Input and Output Isolation
    15. 8.15 Buffer Mode Characteristics
    16. 8.16 PCIe Spread Spectrum Generator
    17. 8.17 LVCMOS Output Characteristics
    18. 8.18 LP-HCSL Output Characteristics
    19. 8.19 LVDS Output Characteristics
    20. 8.20 Output Synchronization Characteristics
    21. 8.21 Power-On Reset Characteristics
    22. 8.22 I2C-Compatible Serial Interface Characteristics
    23. 8.23 Timing Requirements, I2C-Compatible Serial Interface
    24. 8.24 Power Supply Characteristics
    25. 8.25 Typical Characteristics
  10. 9 Parameter Measurement Information
    1. 9.1 Reference Inputs
    2. 9.2 Outputs
    3. 9.3 Serial Interface
    4. 9.4 PSNR Test
    5. 9.5 Clock Interfacing and Termination
      1. 9.5.1 Reference Input
      2. 9.5.2 Outputs
  11. 10Detailed Description
    1. 10.1 Overview
    2. 10.2 Functional Block Diagram
    3. 10.3 Feature Description
      1. 10.3.1 Reference Block
        1. 10.3.1.1 Zero Delay Mode, Internal and External Path
      2. 10.3.2 Phase-Locked Loop (PLL)
        1. 10.3.2.1 PLL Configuration and Divider Settings
        2. 10.3.2.2 Spread Spectrum Clocking
        3. 10.3.2.3 Digitally-Controlled Oscillator and Frequency Increment or Decrement - Serial Interface Mode and GPIO Mode
      3. 10.3.3 Clock Distribution
        1. 10.3.3.1 Glitchless Operation
        2. 10.3.3.2 Divider Synchronization
        3. 10.3.3.3 Global and Individual Output Enable
      4. 10.3.4 Power Supplies and Power Management
      5. 10.3.5 Control Pins
    4. 10.4 Device Functional Modes
      1. 10.4.1 Operation Modes
        1. 10.4.1.1 Fall-Back Mode
        2. 10.4.1.2 Pin Mode
        3. 10.4.1.3 Serial Interface Mode
    5. 10.5 Programming
      1. 10.5.1 I2C Serial Interface
      2. 10.5.2 EEPROM
        1. 10.5.2.1 EEPROM - Cyclic Redundancy Check
        2. 10.5.2.2 Recommended Programming Procedure
        3. 10.5.2.3 EEPROM Access
          1. 10.5.2.3.1 Register Commit Flow
          2. 10.5.2.3.2 Direct Access Flow
        4. 10.5.2.4 Register Bits to EEPROM Mapping
  12. 11Application and Implementation
    1. 11.1 Application Information
    2. 11.2 Typical Application
      1. 11.2.1 Design Requirements
      2. 11.2.2 Detailed Design Procedure
      3. 11.2.3 Application Curves
    3. 11.3 Power Supply Recommendations
      1. 11.3.1 Power-Up Sequence
      2. 11.3.2 Decoupling
    4. 11.4 Layout
      1. 11.4.1 Layout Guidelines
      2. 11.4.2 Layout Examples
  13. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Development Support
      2. 12.1.2 Device Nomenclature
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Support Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  14. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

10.5.2.2 Recommended Programming Procedure

TI recommends programming the registers of the device in the following way:

  1. Read-back factory default EEPROM page configuration. Each device will have different EEPROM base page configuration.
  2. Modify register bits.
  3. Ensure that ee_lock is set to 5h (unlock) when overwriting the EEPROM.
  4. Program register addresses in descending order from 0x53 to 0x00 including all register addresses with reserved values.