DLPS138 Data sheet

DLPS138D july 2018 – july 2023 DLP230KP

PRODUCTION DATA

Package Options

Mechanical Data (Package|Pins)

FQP|54
- MGCC003A

Thermal pad, mechanical data (Package|Pins)

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted⁽¹⁾

			MIN	MAX	UNIT
Supply voltage	V_DD	Supply voltage for LVCMOS core logic⁽²⁾ Supply voltage for LPSDR low speed interface	–0.5	2.3	V
	V_DDI	Supply voltage for SubLVDS receivers⁽²⁾	–0.5	2.3	V
	V_OFFSET	Supply voltage for HVCMOS and micromirror electrode⁽²⁾ ⁽³⁾	–0.5	11	V
	V_BIAS	Supply voltage for micromirror electrode⁽²⁾	–0.5	19	V
	V_RESET	Supply voltage for micromirror electrode⁽²⁾	–15	0.5	V
	\|V_DDI–V_DD\|	Supply voltage delta (absolute value)⁽⁴⁾		0.3	V
	\|V_BIAS–V_OFFSET\|	Supply voltage delta (absolute value)⁽⁵⁾		11	V
	\|V_BIAS–V_RESET\|	Supply voltage delta (absolute value)⁽⁶⁾		34	V
Input voltage	Input voltage for other inputs LPSDR⁽²⁾		–0.5	V_DD + 0.5	V
Input voltage	Input voltage for other inputs SubLVDS⁽²⁾ ⁽⁷⁾		–0.5	V_DDI + 0.5	V
Input pins	\|V_ID\|	SubLVDS input differential voltage (absolute value)⁽⁷⁾		810	mV
Input pins	I_ID	SubLVDS input differential current		10	mA
Clock frequency	ƒ_clock	Clock frequency for low speed interface LS_CLK		130	MHz
Clock frequency	ƒ_clock	Clock frequency for high speed interface DCLK		620	MHz
Environmental	T_ARRAY and T_WINDOW	Temperature – operational ⁽⁸⁾	–20	90	°C
	T_ARRAY and T_WINDOW	Temperature – non-operational⁽⁸⁾	–40	90	°C
	\|T_DELTA\|	Absolute temperature delta between any point on the window edge and the ceramic test point TP1⁽⁹⁾		30	°C
	T_DP	Dew Point - operating and non-operating		81	°C

(1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute Maximum Ratings do not imply functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions. If outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not be fully functional, and this may affect device reliability, functionality, performance, and shorten the device lifetime.

(2) All voltage values are with respect to the ground terminals (V_SS). The following power supplies are all required to operate the DMD: V_DD, V_DDI, V_OFFSET, V_BIAS, and V_RESET. All V_SS connections are also required.

(3) V_OFFSET supply transients must fall within specified voltages.

(4) Exceeding the recommended allowable absolute voltage difference between V_DDI and V_DD may result in excessive current draw.

(5) Exceeding the recommended allowable absolute voltage difference between V_BIAS and V_OFFSET may result in excessive current draw.

(6) Exceeding the recommended allowable absolute voltage difference between V_BIAS and V_RESET may result in excessive current draw.

(7) This maximum input voltage rating applies when each input of a differential pair is at the same voltage potential. SubLVDS differential inputs must not exceed the specified limit or damage may result to the internal termination resistors.

(8) The highest temperature of the active array (as calculated in Section 7.6) or of any point along the window edge is defined in Figure 7-1. The location of thermal test point TP2 in Figure 7-1 is intended to measure the highest window edge temperature. If a particular application causes another point on the window edge to be at a higher temperature, that point should be used.

(9) Temperature delta is the highest difference between the ceramic test point 1 (TP1) and anywhere on the window edge as shown in Figure 7-1. The window test point TP2 shown in Figure 7-1 is intended to result in the worst case delta. If a particular application causes another point on the window edge to result in a larger delta temperature, that point should be used.