DLPS227A october   2021  – june 2023 DLPA300

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics Control Logic
    6. 6.6  5-V Linear Regulator
    7. 6.7  Bias Voltage Boost Converter
    8. 6.8  Reset Voltage Buck-Boost Converter
    9. 6.9  VOFFSET Regulator
    10. 6.10 Switching Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 5-V Linear Regulator
      2. 7.3.2 Bias Voltage Boost Converter
      3. 7.3.3 Reset Voltage Buck-Boost Converter
      4. 7.3.4 VOFFSET Regulator
      5. 7.3.5 Serial Communications Port (SCP)
    4. 7.4 Device Functional Modes
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Component Selection Guidelines
      3. 8.2.3 Application Curves
  10. 9 Power Supply Recommendations
    1. 9.1 Power Supply Rail Guidelines
  11. 10Layout
    1. 10.1 Layout Guidelines
      1. 10.1.1 Grounding Guidelines
    2. 10.2 Thermal Considerations
  12. 11Device and Documentation Support
    1. 11.1 Third-Party Products Disclaimer
    2. 11.2 Device Support
      1. 11.2.1 Device Nomenclature
    3. 11.3 Documentation Support
      1. 11.3.1 Related Documentation
    4. 11.4 Receiving Notification of Documentation Updates
    5. 11.5 Support Resources
    6. 11.6 Trademarks
    7. 11.7 Electrostatic Discharge Caution
    8. 11.8 Glossary
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • PFP|80
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.3.4 VOFFSET Regulator

The VOFFSET regulator supplies the internal VOFFSET voltage for the high voltage FET switches. The VOFFSET voltage level for the 9-μm pixel family of DMDs is 10-V during normal operation and 4.5-V during power down. The VOFFSET voltage level is configured by the DLP controller chip over the serial communication port. Four control bits select the voltage level while a fifth bit is the on/off control. The module provides two status bits to indicate latched and unlatched status bits for undervoltage (VUV) and current-limit (CL) conditions.

Figure 7-3 shows the block diagram of this module. The input decoupling capacitors are shared with other DLPA300 modules. See Section 8.2.2.1 for recommended component values.

GUID-E5D03652-C700-459D-9DAE-65FD6563149B-low.gif Figure 7-3 Offset Voltage Boost Convertor Block Diagram