DLPS030 Data sheet

DLPS030E December 2013 – March 2019 DLPC2607

PRODUCTION DATA.

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)

ZVB|176

Thermal pad, mechanical data (Package|Pins)

5 Pin Configuration and Functions

ZVB Package

176-Pin NFBGA

Bottom View

Pin Functions ⁽¹⁾

PIN		I/O		CLOCK SYSTEM	DESCRIPTION
NAME	NO.	POWER	TYPE	CLOCK SYSTEM	DESCRIPTION
DEVICE INITIALIZATION AND REFERENCE CLOCK⁽¹⁾
RESETZ	J14	VCC18	I1	Async	DLPC2607 power-on reset. Self-configuration starts when a low-to-high transition is detected on this pin. All ASIC power and clocks must be stable before this reset is de-asserted (hysteresis buffer). Note that the following seven signals tri-state while RESET is asserted: DMD_PWR_EN, LEDDVR_ON, LED_SEL_0,LED_SEL_1, SPICLK, SPIDOUT, SPICSZ0 Add external pullup or pulldown resistors as needed to these signals to avoid floating inputs.
PLL_REFCLK_I	K15	VCC18 (filter)	I4	N/A	Reference clock crystal input. If an external oscillator is used in place of a crystal, then use this pin as the oscillator Input.
PLL_REFCLK_O	J15	VCC18 (filter)	O14	N/A	Reference clock crystal return. If an external oscillator is used in place of a crystal, then leave this pin unconnected (floating).
FLASH INTERFACE⁽²⁾
SPICLK	A4	VCC_ FLSH	O24	N/A	Clock for the external SPI device or devices
SPIDIN	B4		I2	SPICLK	Serial data input from the external SPI device or devices
SPICSZ0	A5		O24	SPICLK	Chip select 0 output for the external SPI flash device. Active low
SPICSZ1	C6		O24	SPICLK	Chip select 1 output for the external SPI DLPA1000 device. Active low
SPIDOUT	C5		O24	SPICLK	Serial data output to the external SPI device or devices. This pin sends address and control information as well as data when programming
MAIN VIDEO DATA AND CONTROL
PARK	B8	VCC_ INTF	I3	Async	DMD park control (active low) is set high to enable typical operation. Establish this setting prior to releasing RESET, or within 500 µs after releasing RESET. It should be set low to a minimum of 500 µs before any power is to be removed from the DLPC2607 (hysteresis buffer).
LED_ENABLE	A11	VCC_ INTF	I3	Async	LED enable (active high input). A logic low on this signal forces LEDDRV_ON low and LED_SEL(1:0) = b00. These signals are enabled 100 ms after LED_ENABLE transitions from low to high (hysteresis buffer).
DBIC_CSZ	B10	VCC_ INTF	I3	SCL	Unused/reserved: Pull up to VCC_INTF.
SCL	A10	VCC_ INTF	B38	N/A	I²C clock (hysteresis buffer) bidirectional, open-drain signal. An external pullup is required. No I²C activity is permitted for a minimum of 100 ms after PARK and RESET are set high.
SDA	C10	VCC_ INTF	B38	SCL	I²C data (hysteresis buffer) bidirectional, open-drain signal. An external pullup is required.
GPIO4_INTF	C9	VCC_ INTF	B34	Async	General purpose I/O 4 (hysteresis buffer). Primary usage is to indicate when auto-initialization is complete (also referred to as INIT-DONE, which is when GPIO4 transitions high then low following release of RESET) and to flag a detected error condition in the form of a logic high, pulsed Interrupt flag subsequent to INIT-DONE.
GPIO5_INTF	B9	VCC_ INTF	B34	Async	General purpose I/O 5 (hysteresis buffer). For applications that use focus motor control with a sensor, this pin is an input that is connected to the motor position sensor. For applications that use non-focus motor control with a sensor, configure this pin with an output at logic 0 and left unconnected.
MAIN VIDEO DATA AND CONTROL					PARALLEL RGB MODE	BT.656 I/F MODE
PCLK (Hysteresis)	D13	VCC_ INTF	I3	N/A	Pixel clock ⁽⁷⁾	Pixel clock ⁽⁷⁾
PDM_CVS_TE	H15	VCC_ INTF	B34	ASYNC	Parallel data mask ⁽⁵⁾	Unused ⁽⁴⁾
VSYNC_WE	H14	VCC_ INTF	I3	ASYNC	Vsync ⁽⁶⁾	Unused⁽⁴⁾
HSYNC_CS	H13	VCC_ INTF	I3	PCLK	Hsync ⁽⁶⁾	Unused ⁽⁴⁾
DATEN_CMD	G15	VCC_ INTF	I3	PCLK	Data valid ⁽⁶⁾	Unused ⁽⁴⁾
PDATA[0]	G14	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Data0 ⁽³⁾
PDATA[1]	G13	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Data1 ⁽³⁾
PDATA[2]	F15	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Data2 ⁽³⁾
PDATA[3]	F14	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Data3 ⁽³⁾
PDATA[4]	F13	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Data4 ⁽³⁾
PDATA[5]	E15	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Data5 ⁽³⁾
PDATA[6]	E14	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Data6 ⁽³⁾
PDATA[7]	E13	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Data7 ⁽³⁾
PDATA[8]	D15	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[9]	D14	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[10]	C15	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[11]	C14	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[12]	C13	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[13]	B15	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[14]	B14	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[15]	A15	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[16]	A14	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[17]	B13	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[18]	A13	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[19]	C12	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[20]	B12	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[21]	A12	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
PDATA[22]	C11	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused⁽⁴⁾
PDATA[23]	B11	VCC_ INTF	I3	PCLK	Data ⁽³⁾	Unused ⁽⁴⁾
DMD INTERFACE
DMD_D0	M15	VCC18	O58	DMD_DCLK	DMD Data Pins. DMD Data pins are double data rate (DDR) signals that are clocked on both edges of DMD_DCLK. All 15 DMD data signals are use to interface to the WVGA and VGA DMDs; however, only 12 of the 15 are used to interface to an nHD DMD. The standard nHD interconnect is to utilize pins DMD_D(11:0). However, DMD_D(14:3) must be used to interface to the nHD DMD when the I²C programmable option to reverse the bit-order of the DMD interface pins is selected (DMD Bus Swap Control, I²C: 0xA7).
DMD_D1	N14
DMD_D2	M14
DMD_D3	N15
DMD_D4	P13
DMD_D5	P14
DMD_D6	P15
DMD_D7	R15
DMD_D8	R12
DMD_D9	N11
DMD_D10	P11
DMD_D11	R11
DMD_D12	N10
DMD_D13	P10
DMD_D14	R10
DMD_DCLK	N13			N/A	DMD Data Clock (DDR)
DMD_LOADB	R13			DMD_DCLK	DMD Data Load Signal (active low). This signal requires an external pullup to VCC18.
DMD_SCTRL	R14			DMD_DCLK	DMD Data Serial Control Signal
DMD_TRC	P12			DMD_DCLK	DMD Data Toggle Rate Control
DMD_DAD_BUS	L13			DMD_SAC_CLK	DMD DAD Bus Data
DMD_DAD_STRB	K13			DMD_SAC_CLK	DMD DAD Bus Strobe
DMD_DAD_OEZ	M13			Async	DMD Reset Driver Output Enable (active low). To properly park the DMD, this signal requires a 30-kΩ to 100-kΩ external pullup resistor connected to VCC18.
DMD_SAC_BUS	L15			DMD_SAC_CLK	DMD SAC Bus Data
DMD_SAC_CLK	L14			N/A	DMD SAC Bus Clock
SDRAM INTERFACE
MEM0_CLK_P	D1	VCC18	O74	N/A	mDDR memory, Differential Memory Clock
MEM0_CLK_N	E1		O74		mDDR memory, Differential Memory Clock
MEM0_A0	P1		O64	MEM_CLK	mDDR memory, Multiplexed Row, and Column Address
MEM0_A1	R3
MEM0_A2	R1
MEM0_A3	R2
MEM0_A4	A1
MEM0_A5	B1
MEM0_A6	A2
MEM0_A7	B2
MEM0_A8	D2
MEM0_A9	A3
MEM0_A10	P2
MEM0_A11	B3
MEM0_A12	D3
MEM0_BA0	M3				mDDR memory, Bank Select
MEM0_BA1	P3				mDDR memory, Bank Select
MEM0_RASZ	P4				mDDR memory, Row Address Strobe (active low)
MEM0_CASZ	R4				mDDR memory, Column Address Strobe (active low)
MEM0_WEZ	R5				mDDR memory, Write Enable (active low)
MEM0_CSZ	J3				mDDR memory, Chip Select (active low)
MEM0_CKE	C1				mDDR memory, Clock Enable (active high)
MEM0_LDQS	J2		B64	N/A	mDDR memory, Lower Byte, R/W Data Strobe
MEM0_LDM	J1		O64	MEM0_LDQS	mDDR memory, Lower Byte, Write Data Mask
MEM0_DQ0	N1		B64	MEM0_LDQS	mDDR memory, Lower Byte, Bidirectional R/W Data
MEM0_DQ1	M2
MEM0_DQ2	M1
MEM0_DQ3	L3
MEM0_DQ4	L2
MEM0_DQ5	K2
MEM0_DQ6	L1
MEM0_DQ7	K1
MEM0_UDQS	G1		B64	N/A	mDDR memory, Upper Byte, R/W Data Strobe
MEM0_UDM	H1		O64	MEM0_UDQS	mDDR memory, Upper Byte, Write Data Mask
MEM0_DQ8	H2		B64	MEM0_UDQS	mDDR memory, Upper Byte, Bidirectional R/W Data
MEM0_DQ9	G2
MEM0_DQ10	H3
MEM0_DQ11	F3
MEM0_DQ12	F1
MEM0_DQ13	E2
MEM0_DQ14	F2
MEM0_DQ15	E3
LED DRIVER INTERFACE
GPIO1_RPWM	N8	VCC18	O14	Async	General-purpose I/O 1 (output only). If the DLPA1000 is not used, then this output must be used as the red LED PWM signal used to control the LED current.⁽⁸⁾ If the DLPA1000 is used, then this output can be used as a general purpose output controlled by the WPC processor.
GPIO2_GPWM	P9		O14	Async	General-purpose I/O 2 (output only). If the DLPA1000 is not used, then this output must be used as the green LED PWM signal used to control the LED current.⁽⁸⁾ If the DLPA1000 is used, then this output can be used as a general purpose output controlled by the WPC processor.
GPIO3_BPWM	R8		O14	Async	General-purpose I/O 3 (output only). If the DLPA1000 is not used, then this output must be used as the blue LED PWM signal used to control the LED current.⁽⁸⁾ If the DLPA1000 is used, then this output can be used as a general-purpose output controlled by the WPC processor.
LED_SEL_0	R6		O14	Async	LED enable SELECT. Controlled by programmable DMD sequence timing (hysteresis buffer).
LED_SEL_1	N6		O14	Async	LED_SEL(1:0)	Selected LED
					00	None
					01	Red
					10	Green
					11	Blue
					These outputs should be input directly to the DLPA1000 if used. If the DLPA1000 is not used, then a decode circuit is required to decode the selected LED enable.
LEDDRV_ON	P7		O14	Async	LED driver enable. Active-high output control to external LED driver logic (master enable). It is driven high 100 ms after LED_ENABLE is driven high and driven low immediately when either LED_ENABLE or PARK is driven low.
DMD_PWR_EN	K14		O14	Async	DMD power regulator enable (active high). This is an active-high output that should be used to control DMD V_OFFSET, V_BIAS, and V_RESET voltages. DMD_PWR_EN is driven high when the PARK input signal is set high. However, DMD_PWR_EN is held high for 500 µs after the PARK input signal is set low before it is driven low. TI recommends a weak external pulldown resistor to keep this signal at a known state during power-up reset.
WHITE POINT CORRECTION LIGHT SENSOR I/F
CMP_OUT	A6	VCC_ 18	I1	Async	Successive approximation ADC comparator output (DLPC2607 input). Assumes a successive approximation ADC is implemented with either a light sensor or thermocouple or both feeding one input of an external comparator and the other side of the comparator driven from the CMP_PWM pin of the ASIC. If this function is not used, pull it down to ground (hysteresis buffer).
CMP_PWM	B7		O14	Async	Successive approximation comparator pulse-width modulation input. Supplies a PWM signal to drive the successive approximation ADC Comparator used in light-to-voltage light sensor applications. If this function is not used, leave it unconnected.
GPIO0_CMPPWR	P5		B14	Async	Power control signal for the WPC light sensor and other analog support circuits using the DLPC2607 ADC. Alternately, it provides general purpose I/O to the WPC microprocessor internal to the DLPC2607 device. If not used, leave it unconnected (hysteresis buffer).
HWTEST_EN	A9	VCC _INTF	I3	N/A	Manufacturing test enable signal. Connect directly to ground on the PCB for typical operation. Includes weak internal pulldown.
JTAGTDI	P6	VCC _18	I1	JTAGTCK	JTAG, serial data in. Includes weak internal pullup. (When JTAGRSTZ is held low, this input can be used as ICP/ WPC debug port RXD.)
JTAGTCK	N5			N/A	JTAG, serial data clock. Includes weak internal pullup.
JTAGTMS	N7			JTAGTCK	JTAG, test mode select. Includes weak internal pullup.
JTAGTDO	R7		O14	JTAGTCK	JTAG, serial data out
JTAGRSTZ	P8		I1	ASYNC	JTAG, RESET (active low). Includes weak internal pullup. This signal must be tied to ground, through an external ≤15-kΩ resistor, for typical operation.
TEST AND DEBUG INTERFACES
TSTPT_0	B6	VCC18	B18	Async	Test pin 0 – Sampled as an input test mode selection control upon release of RESET, and then driven as an output. Includes weak internal pulldown.⁽⁹⁾ Normal use: Reserved for test output (ICP/ WPC debug port TXD). Leave open or unconnected for typical use. Alternative use: If focus motor control is used, use this pin as the motor driver chip enable. Do not apply an external pullup to this pin to avoid putting the DLPC2607 device in a test mode.
TSTPT_1	A8	VCC18	B18	Async	Test pin 1 – Sampled as an input test mode selection control upon release of RESET, and then driven as an output. Includes weak internal pulldown.⁽⁹⁾ Normal use: Reserved for test output. Leave open or unconnected for typical use. Alternative use: If focus motor control is used, use this pin as the motor driver data bit1 (LSB). Do not apply an external pullup to this pin to avoid putting the DLPC2607 device in a test mode.
TSTPT_2	C7	VCC18	B18	Async	Test pin 2 – Sampled as an input test mode selection control upon release of RESET, and then driven as an output. Includes weak internal pulldown.⁽⁹⁾ Normal use: Reserved for test output. Leave open or unconnected for typical use. Alternative use: If focus motor control is used, use this pin as the motor driver data bit2. Do not apply an external pullup to this pin to avoid putting the DLPC2607 device in a test mode.
TSTPT_3	B5	VCC18	B18	Async	Test Pin 3 – Sampled as an input test mode selection control upon release of RESET, and then driven as an output. Includes weak internal pulldown.⁽⁹⁾ Normal use: Reserved for test output. Leave open or unconnected for typical use. Alternative use: If focus motor control is used, use this pin as the motor driver motor driver data bit3. Do not apply an external pullup to this pin to avoid putting the DLPC2607 device in a test mode.
TSTPT_4	A7	VCC18	B18	Async	Test pin 4 – Sampled as an input test mode selection control upon release of RESET, and then driven as an output. Includes weak internal pulldown.⁽⁹⁾ Normal use: Reserved for test output. Leave open or unconnected for typical use. Alternative use: If focus motor control is used, use this pin as the motor driver data bit4 (MSB). Do not apply an external pullup to this pin to avoid putting the DLPC2607 device in a test mode.
					Without External Pullup⁽⁹⁾	With External Pullup⁽¹⁰⁾
					Enables auto-initialization from flash	Disables auto-initialization and facilitates flash programming via I²C of a blank flash
TSTPT_5	C8	VCC18	B18	Async	Test pin 5 – Sampled as an input test mode selection control upon release of RESET and then driven as an output. Includes weak internal pulldown.⁽⁹⁾ Normal use: Reserved for test output. Leave open or unconnected for typical use. Alternative use: Not yet defined. Do not apply an external pullup to this pin to avoid putting the DLPC2607 device in a test mode.
TSTPT_6	N9	VCC18	B18	Async	Test pin 6 and PLL REFCLK frequency selection – Sampled as an input test mode selection control upon release of RESET and then driven as an output. Includes a weak internal pulldown.⁽⁹⁾ Normal use: Reserved for test output. Leave open or unconnected for typical use. Alternative use: Not yet defined. This pin is sampled upon de-assertion of RESTZ to determine REFCLK frequency selection. DLPC2607 I²C address is set corresponding to the sampled input value as follows:
					Without External Pullup⁽⁹⁾	With External Pullup⁽¹⁰⁾
					PLL assumes REFCLK = 16.67 MHz	PLL assumes REFCLK = 8.33 MHz
TSTPT_7	R9	VCC18	B18	Async	Test pin 7 and I²C address selection – Sampled as an input test mode selection control upon release of RESET, and then driven as an output. Includes weak internal pulldown. Normal use: Reserved for test output. Leave open or unconnected for typical use. Alternative use: Not yet defined. This pin is sampled upon deassertion of RESET to determine I²C address selection. DLPC2607 I²C address is set corresponding to the sampled input value as follows:
					Without External Pullup⁽⁹⁾	With External Pullup⁽¹⁰⁾
					I²C slave Write Address = x36 I²C slave Read Address = x37	I²C slave Write Address = x3A I²C slave Read Address = x3B
POWER AND GROUND⁽¹¹⁾
VDD10	D5, D9, F4, F12, J4, J12, M6, M8, M11				1-V core logic power supply
VDD_PLL	H12				1-V power supply for the internal PLL
VCC18	C4, D8, E4, G3, K3, K12, L4, M5, M9, M12, N4, N12				1.8-V power supply for all I/O other than the host, video interface, and SPI flash buses
VCC_FLSH	D6				1.8-V, 2.5-V, or 3.3-V power supply for SPI flash bus I/O
VCC_INTF	D11, E12				1.8-V, 2.5-V, or 3.3-V power supply for all I/Os on the host or video interface (includes I²C, PDATA, video syncs, PARK, and LED_ENABLE pins)
GND	D4, D7, D10, D12, G4, G12, H4, K4, L12, M4, M7, M10				Common ground
RTN_PLL	J13				Analog ground return for the PLL (This must be connected to the common ground GND through a ferrite.)
Reserved	C2, C3, N2, N3				No connects. Other signals can be routed through the ball on these pins (versus going around them) to ease routing if desired

(1) Each device connected to the serial peripheral interface (SPI) bus must be operated off VCC_FLSH

(2) Each device connected to the SPI bus must be operated off VCC_FLSH

(3) PDATA(23:0) bus mapping is pixel format and source mode dependent.

(4) Pull unused inputs to ground through an external resistor.

(5) Data mask is optional for parallel bus operation. If unused, pull to ground through a resistor.

(6) VSYNC, HSYNC, and data valid polarity is software programmable.

(7) Pixel clock capture edge is software programmable.

(8) The DLPA1000 is not available for initial DLPC2607 design applications. When the DLPA1000 is not used, all LED PWM signals are forced high when LEDDRV_ON = 0, software LED control is disabled, or the sequence stops.

(9) If operation does not call for an external pullup and there is no external logic that might overcome the weak internal pulldown resistor, then this I/O can be left open or unconnected for typical operation. If operation does not call for an external pullup, but there is external logic that might overcome the weak internal pulldown resistor, then TI recommends an external pulldown resistor to ensure a logic low.

(10) External pullup resistor must be 15 kΩ or less.

(11) 134 total signal I/O pins, 38 total power or ground pins, and 4 total reserved pins

Mechanical Data (Package|Pins)

Thermal pad, mechanical data (Package|Pins)

5 Pin Configuration and Functions

Pin Functions (1)

Pin Functions ⁽¹⁾