DLPS271 April   2024 DLPC7530

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Power Electrical Characteristics
    6. 5.6  Pin Electrical Characteristics
    7. 5.7  DMD HSSI Electrical Characteristics
    8. 5.8  DMD Low-Speed LVDS Electrical Characteristics
    9. 5.9  V-by-One Interface Electrical Characteristics
    10. 5.10 FPD-Link LVDS Electrical Characteristics
    11. 5.11 USB Electrical Characteristics
    12. 5.12 System Oscillator Timing Requirements
    13. 5.13 Power Supply and Reset Timing Requirements
    14. 5.14 DMD HSSI Timing Requirements
    15. 5.15 DMD Low-Speed LVDS Timing Requirements
    16. 5.16 V-by-One Interface General Timing Requirements
    17. 5.17 FPD-Link Interface General Timing Requirements
    18. 5.18 Parallel Interface General Timing Requirements
    19. 5.19 Source Frame Timing Requirements
    20. 5.20 Synchronous Serial Port Interface Timing Requirements
    21. 5.21 Controller and Target I2C Interface Timing Requirements
    22. 5.22 Programmable Output Clock Timing Requirements
    23. 5.23 JTAG Boundary Scan Interface Timing Requirements (Debug Only)
    24. 5.24 JTAG ARM Multi-Ice Interface Timing Requirements (Debug Only)
    25. 5.25 Multi-Trace ETM Interface Timing Requirements
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Input Sources
      2. 6.3.2 Processing Delays
      3. 6.3.3 Parallel Interface
      4. 6.3.4 FPD-Link Interface
      5. 6.3.5 V-by-One Interface
      6. 6.3.6 DMD (HSSI) Interface
      7. 6.3.7 Program Memory Flash Interface
      8. 6.3.8 GPIO Supported Functionality
      9. 6.3.9 Debug Support
    4. 6.4 Device Operational Modes
      1. 6.4.1 Standby Mode
      2. 6.4.2 Active Mode
        1. 6.4.2.1 Normal Configuration
        2. 6.4.2.2 Low Latency Configuration
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
  9. 8 Power Supply Recommendations
    1. 8.1 Power Supply Management
    2. 8.2 Hot Plug Usage
    3. 8.3 Power Supplies for Unused Input Source Interfaces
    4. 8.4 Power Supplies
      1. 8.4.1 1.15-V Power Supplies
      2. 8.4.2 1.21V Power Supply
      3. 8.4.3 1.8-V Power Supplies
      4. 8.4.4 3.3-V Power Supplies
  10. 9 Layout
    1. 9.1 Layout Guidelines
      1. 9.1.1  General Layout Guidelines
      2. 9.1.2  Power Supply Layout Guidelines
      3. 9.1.3  Layout Guidelines for Internal Controller PLL Power
      4. 9.1.4  Layout Guideline for DLPC7530 Reference Clock
        1. 9.1.4.1 Recommended Crystal Oscillator Configuration
      5. 9.1.5  V-by-One Interface Layout Considerations
      6. 9.1.6  FPD-Link Interface Layout Considerations
      7. 9.1.7  USB Interface Layout Considerations
      8. 9.1.8  DMD Interface Layout Considerations
      9. 9.1.9  General Handling Guidelines for Unused CMOS-Type Pins
      10. 9.1.10 Maximum Pin-to-Pin, PCB Interconnects Etch Lengths
    2. 9.2 Thermal Considerations
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Third-Party Products Disclaimer
      2. 10.1.2 Device Nomenclature
        1. 10.1.2.1 Device Markings
        2. 10.1.2.2 Package Data
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
      1. 10.6.1 Video Timing Parameter Definitions
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1.     92

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.2 Thermal Considerations

The underlying thermal requirement for the DLPC7530 is that the maximum operating junction temperature (TJ) not be exceeded (defined in the Section 5.3). This temperature is dependent on the operating ambient temperature, heatsink, airflow, PCB design (including the component layout density and the amount of copper used), power dissipation of the DLPC7530, and power dissipation of surrounding components. The DLPC7530’s package is designed to extract heat via the package heat slug to the heatsink, through the thermal balls, and the power and ground planes of the PCB. Thus, heatsink, copper content, and airflow over the PCB are important factors.

The recommended maximum operating ambient temperature (TA) is provided primarily as a design target and is based on the maximum DLPC7530 power dissipation and RθJA at 0m/s,1m/s, and 2m/s of forced airflow, where RθJA is the thermal resistance of the package as measured using the test board described in Section 9.1.1. This test PCB is not necessarily representative of the customer PCB and thus the reported thermal resistance can differ from the actual product application. Although the actual thermal resistance can be different, it is the best information available during the design phase to estimate thermal performance. TI highly recommends that once the host PCB is designed and built, the thermal performance be measured and validated.

To do this, measure the top center case temperature under the worst-case product scenario (max power dissipation, max voltage, max ambient temperature) and validate that the maximum recommended case temperature (TC) is not exceeded. This specification is based on the measured φJT for the DLPC7530 package provides a relatively accurate correlation to junction temperature. Take care when measuring this case temperature to prevent accidental cooling of the package surface. TI recommends a small (approximately 40 gauge) thermocouple. Ensure that the bead and thermocouple wire contact the top of the package. Cover the bead and thermocouple wire with a minimal amount of thermally conductive epoxy. Route the wires closely along the package and the board surface to avoid cooling the bead through the wires.