DLPS271 April   2024 DLPC7530

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Power Electrical Characteristics
    6. 5.6  Pin Electrical Characteristics
    7. 5.7  DMD HSSI Electrical Characteristics
    8. 5.8  DMD Low-Speed LVDS Electrical Characteristics
    9. 5.9  V-by-One Interface Electrical Characteristics
    10. 5.10 FPD-Link LVDS Electrical Characteristics
    11. 5.11 USB Electrical Characteristics
    12. 5.12 System Oscillator Timing Requirements
    13. 5.13 Power Supply and Reset Timing Requirements
    14. 5.14 DMD HSSI Timing Requirements
    15. 5.15 DMD Low-Speed LVDS Timing Requirements
    16. 5.16 V-by-One Interface General Timing Requirements
    17. 5.17 FPD-Link Interface General Timing Requirements
    18. 5.18 Parallel Interface General Timing Requirements
    19. 5.19 Source Frame Timing Requirements
    20. 5.20 Synchronous Serial Port Interface Timing Requirements
    21. 5.21 Controller and Target I2C Interface Timing Requirements
    22. 5.22 Programmable Output Clock Timing Requirements
    23. 5.23 JTAG Boundary Scan Interface Timing Requirements (Debug Only)
    24. 5.24 JTAG ARM Multi-Ice Interface Timing Requirements (Debug Only)
    25. 5.25 Multi-Trace ETM Interface Timing Requirements
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Input Sources
      2. 6.3.2 Processing Delays
      3. 6.3.3 Parallel Interface
      4. 6.3.4 FPD-Link Interface
      5. 6.3.5 V-by-One Interface
      6. 6.3.6 DMD (HSSI) Interface
      7. 6.3.7 Program Memory Flash Interface
      8. 6.3.8 GPIO Supported Functionality
      9. 6.3.9 Debug Support
    4. 6.4 Device Operational Modes
      1. 6.4.1 Standby Mode
      2. 6.4.2 Active Mode
        1. 6.4.2.1 Normal Configuration
        2. 6.4.2.2 Low Latency Configuration
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
  9. 8 Power Supply Recommendations
    1. 8.1 Power Supply Management
    2. 8.2 Hot Plug Usage
    3. 8.3 Power Supplies for Unused Input Source Interfaces
    4. 8.4 Power Supplies
      1. 8.4.1 1.15-V Power Supplies
      2. 8.4.2 1.21V Power Supply
      3. 8.4.3 1.8-V Power Supplies
      4. 8.4.4 3.3-V Power Supplies
  10. 9 Layout
    1. 9.1 Layout Guidelines
      1. 9.1.1  General Layout Guidelines
      2. 9.1.2  Power Supply Layout Guidelines
      3. 9.1.3  Layout Guidelines for Internal Controller PLL Power
      4. 9.1.4  Layout Guideline for DLPC7530 Reference Clock
        1. 9.1.4.1 Recommended Crystal Oscillator Configuration
      5. 9.1.5  V-by-One Interface Layout Considerations
      6. 9.1.6  FPD-Link Interface Layout Considerations
      7. 9.1.7  USB Interface Layout Considerations
      8. 9.1.8  DMD Interface Layout Considerations
      9. 9.1.9  General Handling Guidelines for Unused CMOS-Type Pins
      10. 9.1.10 Maximum Pin-to-Pin, PCB Interconnects Etch Lengths
    2. 9.2 Thermal Considerations
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Third-Party Products Disclaimer
      2. 10.1.2 Device Nomenclature
        1. 10.1.2.1 Device Markings
        2. 10.1.2.2 Package Data
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
      1. 10.6.1 Video Timing Parameter Definitions
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1.     92

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.1.5 V-by-One Interface Layout Considerations

The DLPC7530 V-by-One SERDES differential interface waveform quality and timing is dependent on the total length of the interconnect system, the spacing between traces, the characteristic impedance, etch losses, and how well matched the lengths are across the interface. Thus, ensuring positive timing margin requires attention to many factors.

DLPC7530 I/O timing parameters, V-by-One transmitter timing parameters, as well as Thine specific timing requirements can be found in their corresponding data sheets. PCB routing mismatch can be budgeted and met through controlled PCB routing. PCB related requirements for V-by-One are provided in Table 9-5 as a starting point for the customer.

Table 9-5 V-by-One Interface PBC Related Requirements (1)
PARAMETERMINTYPMAXUNIT
Intra-lane cross-talk
(between VX1_DATAx_P and VX1_DATAx_N)		< 1.5mVpp
Inter-lane cross-talk
(between data lane pairs)		< 1.5mVpp
Cross-talk between data lanes and other signals< 1.5mVpp
Intra-lane skew< 40ps
Inter-lane skew< 5UI
Differential Impedance90100110Ω
(1) If using the minimum trace width and spacing to escape the Controller ball field, widening these out after escape is desirable if practical to achieve the target 100 Ω impedance (e.g. to reduce transmission line losses).

Additional V-by-One layout guidelines:

  • Route the differential signal pairs on the top layer of the PBC to minimize the number of vias. Limit the number of necessary vias to two.
  • Route differential signal pairs over a single ground or power plane using a Micro-strip line configuration. Ground guard traces are also recommended.
  • Do not route the differential signal pairs over the slit of power or ground planes.
  • Minimize the trace length mismatch for each pair, and between each pair, in order to meet the skew requirements.
  • Ensure that the bend angles associated with the differential signal pairs are between 135o and 225o(See Figure 9-12).

DLPC7530 V-by-One Routing ExampleFigure 9-12 V-by-One Routing Example