SLOS919D June   2016  – November 2023 DRV2510-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Analog Input and Configurable Pre-amplifier
      2. 7.3.2 Pulse-Width Modulator (PWM)
      3. 7.3.3 Designed for low EMI
      4. 7.3.4 Device Protection Systems
        1. 7.3.4.1 Diagnostics
          1. 7.3.4.1.1 Load Diagnostics
        2. 7.3.4.2 Faults During Load Diagnostics
        3. 7.3.4.3 Protection and Monitoring
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation in Shutdown Mode
      2. 7.4.2 Operation in Standby Mode
      3. 7.4.3 Operation in Active Mode
    5. 7.5 Programming
      1. 7.5.1 General I2C Operation
      2. 7.5.2 Single-Byte and Multiple-Byte Transfers
      3. 7.5.3 Single-Byte Write
      4. 7.5.4 Multiple-Byte Write and Incremental Multiple-Byte Write
      5. 7.5.5 Single-Byte Read
      6. 7.5.6 Multiple-Byte Read
    6. 7.6 Register Map
      1. 7.6.1 Address: 0x01
      2. 7.6.2 Address: 0x02
      3. 7.6.3 Address: 0x03
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Single-Ended Source
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1 Optional Components
          2. 8.2.1.2.2 Capacitor Selection
          3. 8.2.1.2.3 Solenoid Selection
          4. 8.2.1.2.4 Output Filter Considerations
        3. 8.2.1.3 Application Curves
        4. 8.2.1.4 Differential Input Diagram
  10. 9 Power Supply Recommendations
  11. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.6.1 Address: 0x01

Figure 7-9 0x01
76543210
OVER_TEMP[0]DC_OFFSET[0]OVER_VOLT[0]UNDER_VOLT[0]OVER_CURR[0]LOAD_DIAG[0]Reserved
RO-0RO-0RO-0RO-0RO-0RO-0
Table 7-4 Address: 0x01
BIT FIELD TYPE DEFAULT DESCRIPTION
7 OVER_TEMP RO 0 Shows the current statuts of the thermal protection
0 Temperature is below the over-temperature threshold.
1 Temperature is above the over-temperature threshold.
6 DC_OFFSET RO 0 Shows the status of DC offset protection
0 DC offset protection has not occurred.
1 DC offset protection has occurred.
5 OVER_VOLT RO 0 Shows the status of the over-voltage protection.
0 VDD voltage is below the over-voltage threshold.
1 VDD voltage is above the over-voltage threshold.
4 UNDER_VOLT RO 0 Shows the status of the under-voltage protection.
0 VDD voltage is above the under-voltage threshold.
1 VDD voltage is below the under-voltage threshold.
3 OVER_CURR RO 0 Shows the status of the over-current protection.
0 An over-current event has not occurred.
1 Device shutdown due to over-current.
2 LOAD_DIAG RO 0 Shows the status of the load diagnostics.
0 An open or short has not been detected.
1 An open or short was detected.
1:0 Reserved