SNLS680 December   2020 DS160UP822

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 DC Electrical Characteristics
    6. 6.6 High Speed Electrical Characteristics
    7. 6.7 SMBUS/I2C Timing Characteristics
    8. 6.8 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Linear Equalization
      2. 7.3.2 Flat Gain
      3. 7.3.3 Cross Point
    4. 7.4 Device Functional Modes
      1. 7.4.1 Active Mode
      2. 7.4.2 Standby Mode
    5. 7.5 Programming
      1. 7.5.1 Control and Configuration Interface
        1. 7.5.1.1 Pin Mode
          1. 7.5.1.1.1 Four-Level Control Inputs
        2. 7.5.1.2 SMBUS/I2C Register Control Interface
        3. 7.5.1.3 SMBus/I 2 C Master Mode Configuration (EEPROM Self Load)
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 UPI 2x2 Cross Point Mux for x24 Lane Configuration
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Receiving Notification of Documentation Updates
    2. 11.2 Community Resources
    3. 11.3 Trademarks
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN NOM MAX UNIT
VCC Supply voltage, VCC to GND DC plus AC power should not exceed these limits 3.0 3.3 3.6 V
NVCC Supply noise tolerance1 DC to <50 Hz, sinusoidal 250 mVpp
50 Hz to 500 kHz, sinusoidal 100 mVpp
500 kHz to 2.5 MHz, sinusoidal 33 mVpp
>2.5 MHz, sinusoidal 10 mVpp
TRampVCC VCC supply ramp time From 0 V to 3.0 V 0.150 100 ms
TJ Operating junction temperature –40 115 °C
TA Operating ambient temperature –40 85 °C
PWLVCMOS Minimum pulse width required for the device to detect a valid signal on LVCMOS inputs PD1/0, and READ_EN_N 200 uS
VCCSMBUS SMBus/I2C SDA and SCL open drain termination voltage Supply voltage for open drain pull-up resistor 3.6 V
FSMBus SMBus/I2C clock (SCL) frequency in SMBus slave mode 10 400 kHz
VIDLAUNCH Source differential launch amplitude 800 1200 mVpp
DR Data rate 1 16 Gbps