SWRS289 october   2021 IWR2243

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Functional Block Diagram
  6. 5 Revision History
  7. 6 Device Comparison
    1. 6.1 Related Products
  8. 7 Terminal Configuration and Functions
    1. 7.1 Pin Diagram
    2. 7.2 Signal Descriptions
  9. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Power-On Hours (POH)
    4. 8.4 Recommended Operating Conditions
    5. 8.5 Power Supply Specifications
    6. 8.6 Power Consumption Summary
    7. 8.7 RF Specification
    8. 8.8 Thermal Resistance Characteristics for FCBGA Package [ABL0161]
    9. 8.9 Timing and Switching Characteristics
      1. 8.9.1 Power Supply Sequencing and Reset Timing
      2. 8.9.2 Synchronized Frame Triggering
      3. 8.9.3 Input Clocks and Oscillators
        1. 8.9.3.1 Clock Specifications
      4. 8.9.4 Multibuffered / Standard Serial Peripheral Interface (MibSPI)
        1. 8.9.4.1 Peripheral Description
          1. 8.9.4.1.1 SPI Timing Conditions
          2. 8.9.4.1.2 SPI Peripheral Mode Switching Parameters (SPICLK = input, SPISIMO = input, and SPISOMI = output)
          3. 8.9.4.1.3 SPI Peripheral Mode Timing Requirements (SPICLK = input, SPISIMO = input, and SPISOMI = output)
        2. 8.9.4.2 Typical Interface Protocol Diagram (Peripheral Mode)
      5. 8.9.5 Inter-Integrated Circuit Interface (I2C)
        1. 8.9.5.1 I2C Timing Requirements
      6. 8.9.6 Quad Serial Peripheral Interface (QSPI)
        1. 8.9.6.1 QSPI Timing Conditions
        2. 8.9.6.2 Timing Requirements for QSPI Input (Read) Timings
        3. 8.9.6.3 QSPI Switching Characteristics
      7. 8.9.7 LVDS Interface Configuration
        1. 8.9.7.1 LVDS Interface Timings
      8. 8.9.8 General-Purpose Input/Output
        1. 8.9.8.1 Switching Characteristics for Output Timing versus Load Capacitance (CL)
      9. 8.9.9 Camera Serial Interface (CSI)
        1. 8.9.9.1 CSI Switching Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Subsystems
      1. 9.3.1 RF and Analog Subsystem
        1. 9.3.1.1 Clock Subsystem
        2. 9.3.1.2 Transmit Subsystem
        3. 9.3.1.3 Receive Subsystem
      2. 9.3.2 Host Interface
    4. 9.4 Other Subsystems
      1. 9.4.1 ADC Data Format Over CSI2 Interface
      2. 9.4.2 ADC Channels (Service) for User Application
        1. 9.4.2.1 GPADC Parameters
  11. 10Monitoring and Diagnostic Mechanisms
  12. 11Applications, Implementation, and Layout
    1. 11.1 Application Information
    2. 11.2 Imaging Radar using Cascade Configuration
    3. 11.3 Reference Schematic
    4. 11.4 Layout
      1. 11.4.1 Layout Guidelines
      2. 11.4.2 Stackup Details
  13. 12Device and Documentation Support
    1. 12.1 Device Nomenclature
    2. 12.2 Tools and Software
    3. 12.3 Documentation Support
    4. 12.4 Support Resources
    5. 12.5 Trademarks
    6. 12.6 Electrostatic Discharge Caution
    7. 12.7 Export Control Notice
    8. 12.8 Glossary
  14. 13Mechanical, Packaging, and Orderable Information
    1. 13.1 Packaging Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.9.2 Synchronized Frame Triggering

The IWR2243 device supports a hardware based mechanism to trigger radar frames. An external host can pulse the SYNC_IN signal to start radar frames. The typical time difference between the rising edge of the external pulse and the frame transmission on air (Tlag) is about 160 ns. There is also an additional programmable delay that the user can set to control the frame start time.

The periodicity of the external SYNC_IN pulse should be always greater than the programmed frame periodic in the frame configurations in all instances.

GUID-E6424D31-ACFE-42C9-A347-629B3A173558-low.gifFigure 8-3 Sync In Hardware Trigger
Table 8-5 Frame Trigger Timing
PARAMETERDESCRIPTIONMINMAXUNIT
Tactive_frameActive frame durationUser definedns
Tpulse254000