SNAS598B July   2012  – July 2015 LM4549B

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  ADC Inputs and Outputs
      2. 8.3.2  Analog Mixing: MIX1
      3. 8.3.3  DAC Mixing and 3D Processing
      4. 8.3.4  Analog Mixing: MIX2
      5. 8.3.5  Stereo Mix
      6. 8.3.6  Stereo Outputs
      7. 8.3.7  Mono Output
      8. 8.3.8  Analog Loopthrough and Digital Loopback
      9. 8.3.9  Resets
      10. 8.3.10 Backwards Compatibility
    4. 8.4 Device Functional Modes
      1. 8.4.1 Low Power Modes
      2. 8.4.2 Test Modes
    5. 8.5 Programming
      1. 8.5.1 AC Link Serial Interface Protocol
        1. 8.5.1.1 AC Link Output Frame: SDATA_OUT, Controller Output to LM4549B Input
          1. 8.5.1.1.1 SDATA_OUT: Slot 0 - Tag Phase
          2. 8.5.1.1.2 SDATA_OUT: Slot 1 - Read/Write, Control Address
          3. 8.5.1.1.3 SDATA_OUT: Slot 2 - Control Data
          4. 8.5.1.1.4 SDATA_OUT: Slots 3 & 4 - PCM Playback Left/Right Channels
          5. 8.5.1.1.5 SDATA_OUT: Slots 5 to 12 - Reserved
        2. 8.5.1.2 AC Link Input Frame: SDATA_IN, Controller Input from LM4549B Output
          1. 8.5.1.2.1 SDATA_IN: Slot 0 - Codec/Slot Status Bits
          2. 8.5.1.2.2 SDATA_IN: Slot 1 - Status Address / Slot Request Bits
          3. 8.5.1.2.3 SDATA_IN: Slot 2 - Status Data
          4. 8.5.1.2.4 SDATA_IN: Slot 3 - PCM Record Left Channel
          5. 8.5.1.2.5 SDATA_IN: Slot 4 - PCM Record Right Channel
          6. 8.5.1.2.6 SDATA_IN: Slots 5 to 12 - Reserved
      2. 8.5.2 Multiple Codecs
        1. 8.5.2.1 Extended AC Link
        2. 8.5.2.2 Secondary Codec Register Access
          1. 8.5.2.2.1 Slot 0: TAG bits in Output Frames (Controller to Codec)
          2. 8.5.2.2.2 Extended Audio ID register (28h): Support for Multiple Codecs
    6. 8.6 Register Maps
      1. 8.6.1  Reset Register (00h)
      2. 8.6.2  Master Volume Register (02h)
      3. 8.6.3  Line Level Volume Register (04h)
      4. 8.6.4  Mono Volume Register (06h)
      5. 8.6.5  PC Beep Volume Register (0Ah)
      6. 8.6.6  Mixer Input Volume Registers (Index 0Ch - 18h)
      7. 8.6.7  Record Select Register (1Ah)
      8. 8.6.8  Record Gain Register (1Ch)
      9. 8.6.9  General Purpose Register (20h)
      10. 8.6.10 3D Control Register (22h)
      11. 8.6.11 Power-Down Control / Status Register (26h)
      12. 8.6.12 Extended Audio ID Register (28h)
      13. 8.6.13 Extended Audio Status/Control register (2Ah)
      14. 8.6.14 Sample Rate Control Registers (2Ch, 32h)
      15. 8.6.15 Vendor ID Registers (7Ch, 7Eh)
      16. 8.6.16 Reserved Registers
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
    3. 9.3 System Example
      1. 9.3.1 Improving System Performance
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
  12. 12Device and Documentation Support
    1. 12.1 Community Resources
    2. 12.2 Trademarks
    3. 12.3 Electrostatic Discharge Caution
    4. 12.4 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

11 Layout

11.1 Layout Guidelines

  • The LM4549B must be initialized by using RESET# to perform a Power-On Reset.
  • Don't leave unused Analog inputs floating. Tie all unused inputs together and connect to Analog Ground through a capacitor (that is, 0.1-µF).
  • Do not leave CD_GND floating when using the CD stereo input. CD_GND is the AC signal reference for the CD channels and should be connected to the CD source ground (Analog Ground may also be acceptable) through a 1-µF capacitor.
  • If using a non-standard AC Link controller take care to keep the SYNC and SDATA_IN signals low during Cold Reset to avoid entering the ATE or Vendor test modes by mistake.
  • The PC_Beep input should be muted if not used since it defaults to 0-dB gain on reset, unlike the mute default of the other analog inputs.