SNVS783K January   2012  – August 2021 LM5017

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Control Overview
      2. 7.3.2  VCC Regulator
      3. 7.3.3  Regulation Comparator
      4. 7.3.4  Overvoltage Comparator
      5. 7.3.5  On-Time Generator
      6. 7.3.6  Current Limit
      7. 7.3.7  N-Channel Buck Switch and Driver
      8. 7.3.8  Synchronous Rectifier
      9. 7.3.9  Undervoltage Detector
      10. 7.3.10 Thermal Protection
      11. 7.3.11 Ripple Configuration
      12. 7.3.12 Soft-Start
    4. 7.4 Device Functional Modes
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application Circuit: 12.5-V to 95-V Input and 10-V, 600-mA Output Buck Converter
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1 Custom Design with WEBENCH Tools
          2. 8.2.1.2.2 RFB1, RFB2
          3. 8.2.1.2.3 Frequency Selection
          4. 8.2.1.2.4 Inductor Selection
          5. 8.2.1.2.5 Output Capacitor
          6. 8.2.1.2.6 Type III Ripple Circuit
          7. 8.2.1.2.7 VCC and Bootstrap Capacitors
          8. 8.2.1.2.8 Input Capacitor
          9. 8.2.1.2.9 UVLO Resistors
        3. 8.2.1.3 Application Curves
      2. 8.2.2 Isolated DC/DC Converter Using LM5017
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
          1. 8.2.2.2.1  Transformer Turns Ratio
          2. 8.2.2.2.2  Total IOUT
          3. 8.2.2.2.3  RFB1, RFB2
          4. 8.2.2.2.4  Frequency Selection
          5. 8.2.2.2.5  Transformer Selection
          6. 8.2.2.2.6  Primary Output Capacitor
          7. 8.2.2.2.7  Secondary Output Capacitor
          8. 8.2.2.2.8  Type III Feedback Ripple Circuit
          9. 8.2.2.2.9  Secondary Diode
          10. 8.2.2.2.10 VCC and Boostrap Capacitor
          11. 8.2.2.2.11 Input Capacitor
          12. 8.2.2.2.12 UVLO Resistors
          13. 8.2.2.2.13 VCC Diode
        3. 8.2.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
      2. 11.1.2 Development Support
        1. 11.1.2.1 Custom Design With WEBENCH® Tools
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 Support Resources
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information
8.2.1.2.5 Output Capacitor

The output capacitor is selected to minimize the capacitive ripple across it. The maximum ripple is observed at maximum input voltage and is given by:

Equation 15. GUID-30FBA831-0CE9-4037-B9FB-C3DF4498F254-low.gif

where

  • ΔVripple is the voltage ripple across the capacitor.

Assuming VIN = 95 V and substituting ΔVripple = 10 mV gives COUT = 10.1 μF. A 22-μF standard value is selected for COUT = C9. An X5R or X7R type capacitor with a voltage rating 16 V or higher should be selected.