SNVSB14C April   2018  – October 2021 LM5036

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  High-Voltage Start-Up Regulator
      2. 7.3.2  Undervoltage Lockout (UVLO)
      3. 7.3.3  Reference Regulator
      4. 7.3.4  Oscillator, Synchronized Input
      5. 7.3.5  Voltage-Mode Control
      6. 7.3.6  Primary-Side Gate Driver Outputs (LSG and HSG)
      7. 7.3.7  Half-Bridge PWM Scheme
      8. 7.3.8  Maximum Duty Cycle Operation
      9. 7.3.9  Pre-Biased Start-Up Process
        1. 7.3.9.1 Primary FETs Soft-Start Process
        2. 7.3.9.2 Synchronous Rectifier (SR) Soft-Start Process
      10. 7.3.10 Zero Duty Cycle Operation
      11. 7.3.11 Enhanced Cycle-by-Cycle Current Limiting with Pulse Matching
      12. 7.3.12 Reverse Current Protection
      13. 7.3.13 CBC Threshold Accuracy
      14. 7.3.14 Hiccup Mode Protection
      15. 7.3.15 Hiccup Mode Blanking
      16. 7.3.16 Over-Temperature Protection (OTP)
      17. 7.3.17 Over-Voltage / Latch (ON_OFF Pin)
      18. 7.3.18 Auxiliary Constant On-Time Control
      19. 7.3.19 Auxiliary On-Time Generator
      20. 7.3.20 Auxiliary Supply Current Limiting
      21. 7.3.21 Auxiliary Primary Output Capacitor Ripple
      22. 7.3.22 Auxiliary Ripple Configuration and Control
      23. 7.3.23 Asynchronous Mode Operation of Auxiliary Supply
    4. 7.4 Device Functional Modes
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1  Custom Design With WEBENCH® Tools
        2. 8.2.2.2  Input Transient Protection
        3. 8.2.2.3  Level-Shift Detection Circuit
        4. 8.2.2.4  Applications with VIN > 100-V
        5. 8.2.2.5  Applications without Pre-Biased Start-Up Requirement
        6. 8.2.2.6  UVLO Voltage Divider Selection
        7. 8.2.2.7  Over Voltage, Latch (ON_OFF Pin) Voltage Divider Selection
        8. 8.2.2.8  SS Capacitor
        9. 8.2.2.9  SSSR Capacitor
        10. 8.2.2.10 Half-Bridge Power Stage Design
        11. 8.2.2.11 Current Limit
        12. 8.2.2.12 Auxiliary Transformer
        13. 8.2.2.13 Auxiliary Feedback Resistors
        14. 8.2.2.14 RON Resistor
        15. 8.2.2.15 VIN Pin Capacitor
        16. 8.2.2.16 Auxiliary Primary Output Capacitor
        17. 8.2.2.17 Auxiliary Secondary Output Capacitor
        18. 8.2.2.18 Auxiliary Feedback Ripple Circuit
        19. 8.2.2.19 Auxiliary Secondary Diode
        20. 8.2.2.20 VCC Diode
        21. 8.2.2.21 Opto-Coupler Interface
        22. 8.2.2.22 Full-Bridge Converter Applications
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Custom Design With WEBENCH® Tools
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
        1. 11.2.1.1 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.3.4 Oscillator, Synchronized Input

The oscillator frequency of LM5036 device is set by a resistor connected between the RT pin and AGND. The RT resistor should be located close to the device. To set a desired oscillator frequency (fOSC), the value of RT resistor can be calculated from Equation 1.

Equation 1. GUID-77441367-1DEE-4884-AD47-3CAD5474FA32-low.gif

For example, if the desired oscillator frequency is 400-kHz, that is, each phase (LSG and HSG) switches at 200-kHz, the value of RT is calculated to be 25-kΩ. If the LM5036 device is to be synchronized to an external clock, that signal must be coupled into the RT pin through a 100-pF capacitor. The RT pin voltage is nominally regulated at VRTReg (2-V typical) and the external pulse amplitude should lift the pin to between 3.5-V and 5.0-V on the low-to-high transition. The synchronization pulse width should be between 15-ns and 200-ns. The RT resistor is always required, whether the oscillator is free running or externally synchronized and SYNC frequency must be equal to or greater than the frequency set by the RT resistor.