SNVSCM3
June
2024
LM5171
PRODUCTION DATA
-
1
-
1 Features
-
2 Applications
-
3 Description
-
4 Pin Configuration and Functions
-
5 Specifications
- 5.1
Absolute Maximum Ratings
- 5.2
ESD Ratings
- 5.3
Recommended Operating Conditions
- 5.4
Thermal Information
- 5.5
Electrical Characteristics
- 5.6
Timing Requirements
- 5.7
Typical Characteristics
-
6 Detailed Description
- 6.1
Overview
- 6.1.1
Device Configurations (CFG) and I2C Address
- 6.1.2
Definition of IC Operation Modes
- 6.2
Functional Block Diagram
- 6.3
Feature Description
- 6.3.1
Bias Supplies and Voltage Reference (VCC, VDD, and VREF)
- 6.3.2
Undervoltage Lockout (UVLO) and Controller Enable or
Disable
- 6.3.3
High Voltage Inputs (HV1, HV2)
- 6.3.4
Current Sense Amplifier
- 6.3.5
Control Commands
- 6.3.5.1
Channel Enable Commands (EN1, EN2)
- 6.3.5.2
Direction Command (DIR1 and DIR2)
- 6.3.5.3
Channel Current Setting Commands (ISET1 and ISET2)
- 6.3.6
Channel Current Monitor (IMON1, IMON2)
- 6.3.6.1
Individual Channel Current Monitor
- 6.3.6.2
Multiphase Total Current Monitoring
- 6.3.7
Cycle-by-Cycle Peak Current Limit (IPK)
- 6.3.8
Inner Current Loop Error Amplifier
- 6.3.9
Outer Voltage Loop Error Amplifier
- 6.3.10
Soft Start, Diode Emulation, and Forced PWM Control (SS/DEM1
and SS/DEM2)
- 6.3.10.1
Soft-Start Control by the SS/DEM Pins
- 6.3.10.2
DEM Programming
- 6.3.10.3
FPWM Programming and Dynamic FPWM and DEM Change
- 6.3.10.4
SS Pin as the Restart Timer
- 6.3.10.4.1
Restart Timer in OVP
- 6.3.10.4.2
Restart Timer after a DIR Change
- 6.3.11
Gate Drive Outputs, Dead Time Programming and Adaptive Dead
Time (HO1, HO2, LO1, LO2, DT/SD)
- 6.3.12
Emergency Latched Shutdown (DT/SD)
- 6.3.13
PWM Comparator
- 6.3.14
Oscillator (OSC)
- 6.3.15
Synchronization to an External Clock (SYNCI, SYNCO)
- 6.3.16
Overvoltage Protection (OVP)
- 6.3.17
Multiphase Configurations (SYNCO, OPT)
- 6.3.17.1
Multiphase in Star Configuration
- 6.3.17.2
Daisy-Chain Configurations for 2, 3, or 4 Phases parallel operations
- 6.3.17.3
Daisy-Chain configuration for 6 or 8 phases parallel
operation
- 6.3.18
Thermal Shutdown
- 6.4
Programming
- 6.4.1
Dynamic Dead Time Adjustment
- 6.4.2
UVLO Programming
- 6.5
Registers
- 6.5.1
I2C Serial Interface
- 6.5.2
I2C Bus Operation
- 6.5.3
Clock Stretching
- 6.5.4
Data Transfer Formats
- 6.5.5
Single READ From a Defined Register
Address
- 6.5.6
Sequential READ Starting From a Defined
Register Address
- 6.5.7
Single WRITE to a Defined Register
Address
- 6.5.8
Sequential WRITE Starting From A Defined
Register Address
- 6.5.9
REGFIELD Registers
-
7 Application and Implementation
- 7.1
Application Information
- 7.1.1
Small Signal Model
- 7.1.1.1
Current Loop Small Signal Model
- 7.1.1.2
Current Loop Compensation
- 7.1.1.3
Voltage Loop Small Signal Model
- 7.1.1.4
Voltage Loop Compensation
- 7.2
Typical Application
- 7.2.1
60A, Dual-Phase, 48V to 12V Bidirectional Converter
- 7.2.1.1
Design Requirements
- 7.2.1.2
Detailed Design Procedure
- 7.2.1.2.1
Determining the Duty Cycle
- 7.2.1.2.2
Oscillator Programming
- 7.2.1.2.3
Power Inductor, RMS and Peak Currents
- 7.2.1.2.4
Current Sense (RCS)
- 7.2.1.2.5
Current Setting Limits (ISETx)
- 7.2.1.2.6
Peak Current Limit
- 7.2.1.2.7
Power MOSFETS
- 7.2.1.2.8
Bias Supply
- 7.2.1.2.9
Boot Strap
- 7.2.1.2.10
OVP
- 7.2.1.2.11
Dead Time
- 7.2.1.2.12
Channel Current Monitor (IMONx)
- 7.2.1.2.13
UVLO Pin Usage
- 7.2.1.2.14
HVx Pin Configuration
- 7.2.1.2.15
Loop Compensation
- 7.2.1.2.16
Soft Start
- 7.2.1.2.17
PWM to ISET Pins
- 7.2.1.2.18
Proper Termination of Unused Pins
- 7.2.1.3
Application Curves
- 7.2.1.3.1
Efficiency
- 7.2.1.3.2
Step Load Response
- 7.2.1.3.3
Dual-Channel Interleaving Operation
- 7.2.1.3.4
Typical Start Up and Shutdown
- 7.2.1.3.5
DEM and FPWM
- 7.2.1.3.6
Mode transition between DEM and FPWM
- 7.2.1.3.7
ISET Tracking and PreCharge
- 7.2.1.3.8
Protections
- 7.3
Power Supply Recommendations
- 7.4
Layout
- 7.4.1
Layout Guidelines
- 7.4.2
Layout Examples
-
8 Device and Documentation Support
- 8.1
Device Support
- 8.1.1
Development Support
- 8.2
Receiving Notification of Documentation Updates
- 8.3
Support Resources
- 8.4
Trademarks
- 8.5
Electrostatic Discharge Caution
- 8.6
Glossary
-
9 Revision History
-
10Mechanical, Packaging, and Orderable Information
Package Options
Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information
6.5 Registers