SNVSBT5 Data sheet

SNVSBT5 November 2023 LM5185

PRODUCTION DATA

Package Options

Mechanical Data (Package|Pins)

PWP|14
- MPDS370A

Thermal pad, mechanical data (Package|Pins)

PWP|14
- PPTD022AA

Orderable Information

7.3.2 PSR Flyback Modes of Operation

The LM5185 uses a variable-frequency, peak current-mode (VFPCM) control architecture with three possible modes of operation as illustrated in Figure 7-2.

Figure 7-2 Three Modes of Operation Illustrated by Variation of Switching Frequency With Load

The LM5185 operates in boundary conduction mode (BCM) at heavy loads. The power MOSFET turns on when the current in the secondary winding reaches zero, and the MOSFET turns off when the peak primary current reaches the level dictated by the output of the internal error amplifier. As the load is decreased, the frequency increases to maintain BCM operation. Equation 1 gives the duty cycle of the flyback converter in BCM.

Equation 1.

D = \frac{(V_{O U T} + V_{D}) \times N_{P S}}{V_{I N} + (V_{O U T} + V_{D}) \times N_{P S}}

where

V_D is the forward voltage drop of the flyback diode as the current approaches zero

Equation 2 gives the output power in BCM, where the applicable switching frequency and peak primary current are specified by Equation 3 and Equation 4, respectively.

Equation 2.

P_{O U T (B C M)} = \frac{L_{M A G} \times I_{P R I - P K (B C M)}^{2}}{2} \times F_{S W (B C M)}

Equation 3.

F_{S W (B C M)} = \frac{1}{I_{P R I - P K (B C M)} \times (\frac{L_{M A G}}{V_{I N}} + \frac{L_{M A G}}{N_{P S} \times (V_{O U T} + V_{D})})}

Equation 4.

I_{P R I - P K (B C M)} = \frac{2 \times (V_{O U T} + V_{D}) \times I_{O U T}}{V_{I N} \times D}

As the load decreases, the LM5185 clamps the maximum switching frequency to 350 kHz, and the converter enters discontinuous conduction mode (DCM). The power delivered to the output in DCM is proportional to the peak primary current squared as given by Equation 5 and Equation 6. Thus, as the load decreases, the peak current reduces to maintain regulation at 350-kHz switching frequency.

Equation 5.

P_{O U T (D C M)} = \frac{L_{M A G} \times I_{P R I - P K (D C M)}^{2}}{2} \times F_{S W (D C M)}

Equation 6.

I_{P R I - P K (D C M)} = \sqrt{\frac{2 \times I_{O U T} \times (V_{O U T} + V_{D})}{L_{M A G} \times F_{S W (D C M)}}}

Equation 7.

D_{D C M} = \frac{L_{M A G} \times I_{P R I - P K (D C M)} \times F_{S W (D C M)}}{V_{I N}}

At even lighter loads, the primary-side peak current set by the internal error amplifier decreases to a minimum level of 20 mV on V_CS, or 20% of the 100-mV peak value, and the MOSFET gate off-time extends to maintain the output load requirement. The system operates in frequency foldback mode (FFM), and the switching frequency decreases as the load current is reduced. Other than a fault condition, the lowest frequency of operation of the LM5185 is 11 kHz, which sets a minimum load requirement of approximately 0.5% full load.