SNAS207B May   2004  – January 2024 LM64

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 Operating Ratings
    3. 5.3 DC Electrical Characteristics
    4. 5.4 Operating Electrical Characteristics
    5. 5.5 AC Electrical Characteristics
    6. 5.6 Digital Electrical Characteristics
    7. 5.7 SMBus Logical Electrical Characteristics
    8. 5.8 SMBus Digital Switching Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Conversion Sequence
      2. 6.3.2  The ALERT Output
        1. 6.3.2.1 ALERT Output as a Temperature Comparator
        2. 6.3.2.2 ALERT Output as an Interrupt
        3. 6.3.2.3 ALERT Output as an SMBus ALERT
      3. 6.3.3  SMBus Interface
      4. 6.3.4  Power-On Reset (POR) Default States
      5. 6.3.5  Temperature Data Format
      6. 6.3.6  Open-Drain Outputs, Inputs, and Pull-Up Resistors
      7. 6.3.7  Diode Fault Detection
      8. 6.3.8  Communicating with the LM64
      9. 6.3.9  Digital Filter
      10. 6.3.10 Fault Queue
      11. 6.3.11 One-Shot Register
      12. 6.3.12 Serial Interface Reset
  8. 7 Registers
    1. 7.1 LM64 Registers
      1. 7.1.1 LM64 Register Map in Hexadecimal Order
      2. 7.1.2 LM64 Register Map in Functional Order
      3. 7.1.3 LM64 Initial Register Sequence and Register Descriptions in Functional Order
        1. 7.1.3.1 LM64 Required Initial Fan Control Register Sequence
      4. 7.1.4 LM64 Register Descriptions in Functional Order
        1. 7.1.4.1 Fan Control Registers
        2. 7.1.4.2 Configuration Register
        3. 7.1.4.3 Tachometer Count And Limit Registers
        4. 7.1.4.4 Local Temperature And Local High Setpoint Registers
        5. 7.1.4.5 Remote Diode Temperature, Offset And Setpoint Registers
        6. 7.1.4.6 ALERT Status And Mask Registers
        7. 7.1.4.7 Conversion Rate And One-Shot Registers
        8. 7.1.4.8 ID Registers
    2. 7.2 General Purpose Registers
  9. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Fan Control Duty Cycle VS. Register Settings and Frequency
        1. 8.1.1.1 Computing Duty Cycles for a Given Frequency
      2. 8.1.2 Use of the Lookup Table for Non-Linear PWM Values VS Temperature
      3. 8.1.3 NON-Ideality Factor and Temperature Accuracy
        1. 8.1.3.1 Diode Non_Ideality
        2. 8.1.3.2 Compensating for Diode Non-Ideality
      4. 8.1.4 Computing RPM of the Fan from the TACH Count
    2. 8.2 Typical Application
  10. 9 Layout
    1. 9.1 PCB Layout for Minimizing Noise
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.1.3.1 LM64 Required Initial Fan Control Register Sequence

Important! The BIOS must follow the sequence below to configure the following Fan Registers for the LM64 before using any of the Fan or Tachometer or PWM registers:

Step[Register]HEX and Setup Instructions(1)
1[4A] Write bits 0 and 1; 3 and 4. This includes tach settings if used, PWM internal clock select (1.4 kHz or 360 kHz) and PWM Output Polarity.
2[4B] Write bits 0 through 5 to program the spin-up settings.
3[4D] Write bits 0 through 4 to set the frequency settings. This works with the PWM internal clock select.
4Choose, then write, only one of the following:
A. [4F–5F] the Lookup Table, or
B. [4C] the PWM value bits 0 through 5.
5If Step 4A, Lookup Table, was chosen and written then write [4A] bit 5 = 0.
(1) All other registers can be written at any time after the above sequence.