SNVSCC9B November   2023  – December 2024 LP5812

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Time-Cross-Multiplexing (TCM) Scheme
        1. 7.3.1.1 Direct drive mode
        2. 7.3.1.2 TCM Drive Mode
        3. 7.3.1.3 Mix drive mode
        4. 7.3.1.4 Ghosting Elimination
      2. 7.3.2 Analog Dimming
      3. 7.3.3 PWM Dimming
      4. 7.3.4 Autonomous Animation Engine Control
        1. 7.3.4.1 Animation Engine Pattern
        2. 7.3.4.2 Sloper
        3. 7.3.4.3 Animation Engine Unit (AEU)
        4. 7.3.4.4 Animation Pause Unit (APU)
      5. 7.3.5 Protections and Diagnostics
        1. 7.3.5.1 LED Open Detections
        2. 7.3.5.2 LED Short Detections
        3. 7.3.5.3 Thermal Shutdown
    4. 7.4 Device Functional Modes
    5. 7.5 Programming
    6. 7.6 Register Maps
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Parameters
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1 Input Capacitor Selection
        2. 8.2.3.2 Program Procedure
        3. 8.2.3.3 Programming Example
      4. 8.2.4 Application Performance Plots
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • YBH|9
  • DSD|8
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.2.3.1 Input Capacitor Selection

Input capacitors must be located as close as possible to the device. While a 10μF input capacitor is sufficient for most applications, large capacitance is used to reduce input current ripple. When the input power is supplied through long wire and only ceramic capacitor is put, the load step at the output induces ringing at the VCC pin. This ringing couples back to the output and influence loop stability or even damage the device. In this circumstance, placing additional bulk capacitance (tantalum or aluminum electrolytic capacitor) between ceramic input capacitor and the power supply can reduce the ringing