SNVSCE2B May   2023  – November 2023 LP5868T

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7.     14
    8. 6.7 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Time-Multiplexing Matrix
      2. 7.3.2 Analog Dimming (Current Gain Control)
        1. 7.3.2.1 Global 3-Bits Maximum Current (MC) Setting
        2. 7.3.2.2 3 Groups of 7-Bits Color Current (CC) Setting
        3. 7.3.2.3 Individual 8-bit Dot Current (DC) Setting
      3. 7.3.3 PWM Dimming
        1. 7.3.3.1 Individual 8-Bit / 16-Bit PWM for Each LED Dot
        2. 7.3.3.2 Programmable Groups of 8-Bit PWM Dimming
        3. 7.3.3.3 8-Bit PWM for Global Dimming
      4. 7.3.4 ON and OFF Control
      5. 7.3.5 Data Refresh Mode
      6. 7.3.6 Full Addressable SRAM
      7. 7.3.7 Protections and Diagnostics
        1. 7.3.7.1 LED Open Detection
        2. 7.3.7.2 LED Short Detection
        3. 7.3.7.3 Thermal Shutdown
        4. 7.3.7.4 UVLO (Under Voltage Lock Out)
    4. 7.4 Device Functional Modes
    5. 7.5 Programming
      1. 7.5.1 Interface Selection
      2. 7.5.2 I2C Interface
        1. 7.5.2.1 I2C Data Transactions
        2. 7.5.2.2 I2C Data Format
        3. 7.5.2.3 Multiple Devices Connection
      3. 7.5.3 Programming
        1. 7.5.3.1 SPI Data Transactions
        2. 7.5.3.2 SPI Data Format
        3. 7.5.3.3 Multiple Devices Connection
    6. 7.6 Register Maps
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1 Program Procedure
      4. 8.2.4 Application Performance Plots
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 VDD Input Supply Recommendations
      2. 8.3.2 VLED Input Supply Recommendations
      3. 8.3.3 VIO Input Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.4.1 Layout Guidelines

Below guidelines for layout design can help to get a better on-board performance.

  • The decoupling capacitors CVCC and CVLED for power supply must be close to the chip to have minimized the impact of high-frequency noise and ripple from power. CVCAP for internal LDO must be put as close to chip as possible. GND plane connections to CVLED and GND pins must be on TOP layer copper with multiple vias connecting to system ground plane. CVIO for internal enable block also must be put as close to chip as possible.
  • The exposed thermal pad must be well soldered to the board, which can have better mechanical reliability. This action can optimize heat transfer so that increasing thermal performance. The AGND pin must be connected to thermal pad and system ground.
  • The major heat flow path from the package to the ambient is through copper on the PCB. Several methods can help thermal performance. Below exposed thermal pad of the device, putting much vias through the PCB to other ground layer can dissipate more heat. Maximizing the copper coverage on the PCB can increase the thermal conductivity of the board.
  • Low inductive and resistive path of switch load loop can help to provide a high slew rate. Therefore, path of VLED – SWx must be short and wide and avoid parallel wiring and narrow trace. Transient current in SWx pins is much larger than CSy pins, so that trace for SWx must be wider than CSy.