SLAS982 Data sheet

SLAS982A May 2014 – September 2018 MSP430F6745A , MSP430F6746A , MSP430F6747A , MSP430F6748A , MSP430F6749A , MSP430F6765A , MSP430F6766A , MSP430F6767A , MSP430F6768A , MSP430F6769A , MSP430F6775A , MSP430F6776A , MSP430F6777A , MSP430F6778A , MSP430F6779A

PRODUCTION DATA.

Package Options

Mechanical Data (Package|Pins)

PEU|128
- MPQF058B
PZ|100
- MTQF013A

Thermal pad, mechanical data (Package|Pins)

Orderable Information

Table 5-30 eUSCI (SPI Master Mode) Switching Characteristics

over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)⁽¹⁾

PARAMETER		TEST CONDITIONS	V_CC	MIN	MAX	UNIT
t_STE,LEAD	STE lead time, STE low to clock	UCSTEM = 0, UCMODEx = 01 or 10	2 V, 3 V	150		ns
t_STE,LEAD	STE lead time, STE low to clock	UCSTEM = 1, UCMODEx = 01 or 10	2 V, 3 V	150		ns
t_STE,LAG	STE lag time, Last clock to STE high	UCSTEM = 0, UCMODEx = 01 or 10	2 V, 3 V	200		ns
t_STE,LAG	STE lag time, Last clock to STE high	UCSTEM = 1, UCMODEx = 01 or 10	2 V, 3 V	200		ns
t_STE,ACC	STE access time, STE low to SIMO data out	UCSTEM = 0, UCMODEx = 01 or 10	2 V		50	ns
		UCSTEM = 0, UCMODEx = 01 or 10	3 V		30
		UCSTEM = 1, UCMODEx = 01 or 10	2 V		50
		UCSTEM = 1, UCMODEx = 01 or 10	3 V		30
t_STE,DIS	STE disable time, STE high to SIMO high impedance	UCSTEM = 0, UCMODEx = 01 or 10	2 V		40	ns
		UCSTEM = 0, UCMODEx = 01 or 10	3 V		25
		UCSTEM = 1, UCMODEx = 01 or 10	2 V		40
		UCSTEM = 1, UCMODEx = 01 or 10	3 V		25
t_SU,MI	SOMI input data setup time		2 V	50		ns
t_SU,MI	SOMI input data setup time		3 V	30		ns
t_HD,MI	SOMI input data hold time		2 V	0		ns
t_HD,MI	SOMI input data hold time		3 V	0		ns
t_VALID,MO	SIMO output data valid time⁽²⁾	UCLK edge to SIMO valid, C_L = 20 pF	2 V		9	ns
t_VALID,MO	SIMO output data valid time⁽²⁾	UCLK edge to SIMO valid, C_L = 20 pF	3 V		5	ns
t_HD,MO	SIMO output data hold time⁽³⁾	C_L = 20 pF	2 V	0		ns
t_HD,MO	SIMO output data hold time⁽³⁾	C_L = 20 pF	3 V	0		ns

(1) f_UCxCLK = 1/2t_LO/HI with t_LO/HI = max(t_{VALID,MO(eUSCI)} + t_SU,SI(Slave), t_SU,MI(eUSCI) + t_{VALID,SO(Slave)})
For the slave parameters t_SU,SI(Slave) and t_{VALID,SO(Slave)}, see the SPI parameters of the attached slave.

(2) Specifies the time to drive the next valid data to the SIMO output after the output changing UCLK clock edge. See the timing diagrams in Figure 5-11 and Figure 5-12.

(3) Specifies how long data on the SIMO output is valid after the output changing UCLK clock edge. Negative values indicate that the data on the SIMO output can become invalid before the output changing clock edge observed on UCLK. See the timing diagrams in Figure 5-11 and Figure 5-12.

MSP430F6779A MSP430F6778A MSP430F6777A MSP430F6776A MSP430F6775A MSP430F6769A MSP430F6768A MSP430F6767A MSP430F6766A MSP430F6765A MSP430F6749A MSP430F6748A MSP430F6747A MSP430F6746A MSP430F6745A slas639-eUSCI_master_CKPH0.gif

Figure 5-11 SPI Master Mode, CKPH = 0

Figure 5-12 SPI Master Mode, CKPH = 1

Table 5-31 lists the characteristics of the eUSCI in SPI slave mode.