SBOS673D September   2017  – December 2018 OPA2837 , OPA837

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
    1.     Low-Power, Low-Noise, Precision, Single-Ended SAR ADC Driver With True Ground Input and Output Range
  3. 3 Description
    1.     Device Images
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information: OPA837
    5. 6.5  Thermal Information: OPA2837
    6. 6.6  Electrical Characteristics: VS = 5 V
    7. 6.7  Electrical Characteristics: VS = 3 V
    8. 6.8  Typical Characteristics: VS = 5.0 V
    9. 6.9  Typical Characteristics: VS = 3.0 V
    10. 6.10 Typical Characteristics: ±2.5-V to ±1.5-V Split Supply
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagrams
    3. 7.3 Feature Description
      1. 7.3.1 OPA837 Comparison
      2. 7.3.2 Input Common-Mode Voltage Range
      3. 7.3.3 Output Voltage Range
      4. 7.3.4 Power-Down Operation
      5. 7.3.5 Low-Power Applications and the Effects of Resistor Values on Bandwidth
      6. 7.3.6 Driving Capacitive Loads
    4. 7.4 Device Functional Modes
      1. 7.4.1 Split-Supply Operation (±1.35 V to ±2.7 V)
      2. 7.4.2 Single-Supply Operation (2.7 V to 5.4 V)
  8. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1  Noninverting Amplifier
      2. 8.1.2  Inverting Amplifier
      3. 8.1.3  Output DC Error Calculations
      4. 8.1.4  Output Noise Calculations
      5. 8.1.5  Instrumentation Amplifier
      6. 8.1.6  Attenuators
      7. 8.1.7  Differential to Single-Ended Amplifier
      8. 8.1.8  Differential-to-Differential Amplifier
      9. 8.1.9  Pulse Application With Single-Supply Circuit
      10. 8.1.10 ADC Driver Performance
    2. 8.2 Typical Applications
      1. 8.2.1 Active Filters
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curves
      2. 8.2.2 Implementing a 2:1 Active Multiplexer
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
      3. 8.2.3 1-Bit PGA Operation
        1. 8.2.3.1 Design Requirements
        2. 8.2.3.2 Detailed Design Procedure
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Related Links
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 Community Resources
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.8 Typical Characteristics: VS = 5.0 V

at VS+ = 5.0 V, VS– = 0 V, VOUT = 2 VPP, RF = 0 Ω, RL = 2 kΩ, G = 1 V/V, input and output referenced to mid-supply, and TA ≈ 25°C (unless otherwise noted)
OPA837 OPA2837 D001_SBOS673.gif
See Figure 74 and Table 2, VOUT = 20 mVPP, RLOAD = 2 kΩ
Figure 1. Noninverting Small-Signal Frequency Response
vs Gain
OPA837 OPA2837 D003_SBOS673.gif
Gain = 2 V/V, RLOAD = 2 kΩ
Figure 3. Noninverting Large-Signal Bandwidth vs VOPP
OPA837 OPA2837 D005_SBOS673.gif
See Figure 74 and Table 2, VOUT = 200 mVPP, RLOAD = 2 kΩ
Figure 5. Noninverting Response Flatness vs Gain
OPA837 OPA2837 D007_SBOS673.gif
See Figure 74, gain = 2 V/V,
input edge rate set to stay below slew limiting
Figure 7. Noninverting Step Response vs Time and VOPP
OPA837 OPA2837 D009_SBOS673.gif
See Figure 74 and Table 2
Figure 9. Simulated Noninverting Settling Time
OPA837 OPA2837 D011_SBOS673.gif
See Figure 74 and Table 2, gain = 2 V/V
Figure 11. Noninverting Overdrive Recovery
OPA837 OPA2837 D013_SBOS673.gif
See Figure 74, Figure 75, Table 2, and Table 3, VOUT = 2 VPP
Figure 13. Harmonic Distortion vs Frequency
OPA837 OPA2837 D015_SBOS673.gif
See Figure 74, Figure 75, Table 2, and Table 3, VOUT = 2 VPP,
f = 100 kHz
Figure 15. Harmonic Distortion vs Output Voltage
OPA837 OPA2837 D017_SBOS673.gif
See Figure 87, VOUT = 2 VPP, f = 100 kHz
Figure 17. Harmonic Distortion as Active Mux
OPA837 OPA2837 D002_SBOS673.gif
See Figure 75 and Table 3, VOUT = 20 mVPP, RLOAD = 2 kΩ
Figure 2. Inverting Small-Signal Frequency Response
vs Gain
OPA837 OPA2837 D004_SBOS673.gif
Gain = –1 V/V, RLOAD = 2 kΩ
Figure 4. Inverting Large-Signal Bandwidth vs VOPP
OPA837 OPA2837 D006_SBOS673.gif
See Figure 75 and Table 3, VOUT = 200 mVPP, RLOAD = 2 kΩ
Figure 6. Inverting Response Flatness vs Gain
OPA837 OPA2837 D008_SBOS673.gif
See Figure 75, gain = –1 V/V,
input edge rate set to stay below slew limiting
Figure 8. Inverting Step Response vs Time and VOPP
OPA837 OPA2837 D010_SBOS673.gif
See Figure 75 and Table 3
Figure 10. Simulated Inverting Settling Time
OPA837 OPA2837 D012_SBOS673.gif
See Figure 75 and Table 3, gain –2 V/V
Figure 12. Inverting Overdrive Recovery
OPA837 OPA2837 D014_SBOS673.gif
See Figure 74, Figure 75, Table 2, and Table 3, VOUT = 2 VPP,
f = 100 kHz
Figure 14. Harmonic Distortion vs RLOAD
OPA837 OPA2837 D016_SBOS673.gif
See Figure 74, Figure 75, Table 2, and Table 3, VOUT = 2 VPP,
f = 100 kHz
Figure 16. Harmonic Distortion vs Gain Magnitude
OPA837 OPA2837 D018_SBOS673.gif
See Figure 87, gain of 1 V/V or 2 V/V, VOUT = 2 VPP,
f = 100 kHz
Figure 18. Harmonic Distortion as 1-Bit PGA