SBOS940A May   2019  – March 2020 OPA818

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
    1.     High-Speed Optical Front-End
  3. 3 Description
    1.     Photodiode Capacitance vs 3-dB Bandwidth
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics: VS = ±5 V
    6. 7.6 Typical Characteristics: VS = ±5 V
    7. 7.7 Typical Characteristics: VS = 6 V
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Input and ESD Protection
      2. 8.3.2 Feedback Pin
      3. 8.3.3 Decompensated Architecture With Wide Gain-Bandwidth Product
      4. 8.3.4 Low Input Capacitance
    4. 8.4 Device Functional Modes
      1. 8.4.1 Split-Supply Operation (+4/–2 V to ±6.5 V)
      2. 8.4.2 Single-Supply Operation (6 V to 13 V)
  9. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Wideband, Non-Inverting Operation
      2. 9.1.2 Wideband, Transimpedance Design Using OPA818
    2. 9.2 Typical Applications
      1. 9.2.1 High Bandwidth, 100-kΩ Gain Transimpedance Design
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
        3. 9.2.1.3 Application Curves
      2. 9.2.2 Non-Inverting Gain of 2 V/V
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Thermal Considerations
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Development Support
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 Receiving Notification of Documentation Updates
    4. 12.4 Community Resources
    5. 12.5 Trademarks
    6. 12.6 Electrostatic Discharge Caution
    7. 12.7 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

10 Power Supply Recommendations

The OPA818 is intended for operation on supplies from 6 V (+4/–2 V) to 12 V (±6 V). OPA818 supports single-supply, split and balanced bipolar supplies and unbalanced bipolar supplies. When operating at supplies below 8 V, the mid-supply will be outside the input common-mode range of the amplifier. Under these supply conditions, the common-mode must be biased appropriately for linear operation. Thus the limit to lower supply voltage operation is the useable input voltage range for the JFET-input stage. Operating from a single supply of 12 V can have numerous advantages. With the negative supply at ground, the DC errors due to the –PSRR term can be minimized. Typically, AC performance improves slightly at 12-V operation with minimal increase in supply current.