SCPS129K August   2005  – March 2021 PCA9535

PRODUCTION DATA  

  1. 1 Features
  2. 2 Description
  3. 3 Revision History
  4. 4 Description Continued
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Resistance Characteristics
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Interface Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Typical Characteristics
  7. 7 Parameter Measurement Information
    1.     16
  8. 8 Detailed Description
    1. 8.1 Functional Block Diagram
    2. 8.2 Device Functional Modes
      1. 8.2.1 Power-On Reset
      2. 8.2.2 I/O Port
      3. 8.2.3 Interrupt ( INT) Output
        1. 8.2.3.1 Interrupt Errata
          1.        24
          2.        25
          3.        26
    3. 8.3 Programming
      1. 8.3.1 I2C Interface
      2. 8.3.2 Register Map
        1. 8.3.2.1 Device Address
        2. 8.3.2.2 Control Register And Command Byte
        3. 8.3.2.3 Register Descriptions
        4. 8.3.2.4 Bus Transactions
          1. 8.3.2.4.1 Writes
          2. 8.3.2.4.2 Reads
  9. 9 Application Information Disclaimer
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Minimizing ICC When I/O Is Used To Control Led
  10. 10Power Supply Recommendations
    1. 10.1 Power-On Reset Requirements
  11. 11Device and Documentation Support
    1. 11.1 Receiving Notification of Documentation Updates
    2. 11.2 Support Resources
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.5 Electrical Characteristics

over recommended operating free-air temperature range (unless otherwise noted)
PARAMETERTEST CONDITIONSVCCMINTYP(1)MAXUNIT
VIKInput diode clamp voltageII = –18 mA2.3 V to 5.5 V–1.2V
VPORRPower-on reset voltage, VCC risingVI = VCC or GND, IO = 01.21.65V
VPORFPower-on reset voltage, VCC fallingVI = VCC or GND, IO = 0

0.75

1

V

VOHP-port high-level output voltage(2)IOH = –8 mA2.3 V1.8V
3 V2.6
4.75 V4.1
IOH = –10 mA2.3 V1.7
3 V2.5
4.75 V4
IOLSDAVOL = 0.4 V2.3 V to 5.5 V3mA
P port(3)VOL = 0.5 V820
VOL = 0.7 V1024
INTVOL = 0.4 V3
IISCL, SDAVI = VCC or GND2.3 V to 5.5 V±1μA
A2–A0±1
IIHP portVI = VCC2.3 V to 5.5 V1μA
IILP portVI = GND2.3 V to 5.5 V–1μA
ICCOperating modeVI = VCC or GND, IO = 0,
I/O = inputs, fSCL = 400 kHz		5.5 V100200μA
3.6 V3075
2.7 V2050
Standby modeVI = GND, IO = 0, I/O = inputs,
fSCL = 0 kHz		5.5 V1.5

8.7

3.6 V0.9

4

2.7 V0.6

3

ΔICCAdditional current in standby modeOne input at VCC – 0.6 V,
Other inputs at VCC or GND		2.3 V to 5.5 V200μA
CISCLVI = VCC or GND2.3 V to 5.5 V38pF
CioSDAVIO = VCC or GND2.3 V to 5.5 V3

9.5

pF
P port3.79.5
(1) All typical values are at nominal supply voltage (2.5-V, 3.3-V, or 5-V VCC) and TA = 25°C.
(2) Each I/O must be limited externally to a maximum of 25 mA, and each octal (P07–P00 and P17–P10) must be limited to a maximum current of 100 mA, for a device total of 200 mA.
(3) The total current sourced by all I/Os must be limited to 160 mA (80 mA for P07–P00 and 80 mA for P17–P10).