SLLSEO9D March   2016  – October 2024 SN65DPHY440SS , SN75DPHY440SS

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics, Power Supply
    6. 5.6 Electrical Characteristics
    7. 5.7 Timing Requirements
    8. 5.8 Switching Characteristics
    9. 5.9 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 HS Receive Equalization
      2. 6.3.2 HS TX Edge Rate Control
      3. 6.3.3 TX Voltage Swing and Pre-Emphasis Control
      4. 6.3.4 Dynamic De-skew
    4. 6.4 Device Functional Modes
      1. 6.4.1 Shutdown Mode
      2. 6.4.2 LP Mode
      3. 6.4.3 ULPS Mode
      4. 6.4.4 HS Mode
    5. 6.5 Register Maps
      1. 6.5.1  BIT Access Tag Conventions
      2. 6.5.2  Standard CSR Registers (address = 0x000 - 0x07)
      3. 6.5.3  Standard CSR Register (address = 0x08)
      4. 6.5.4  Standard CSR Register (address = 0x09)
      5. 6.5.5  Standard CSR Register (address = 0x0A)
      6. 6.5.6  Standard CSR Register (address = 0x0B)
      7. 6.5.7  Standard CSR Register (address = 0x0D)
      8. 6.5.8  Standard CSR Register (address = 0x0E)
      9. 6.5.9  Standard CSR Register (address = 0x10) [reset = 0xFF]
      10. 6.5.10 Standard CSR Register (address = 0x11) [reset = 0xFF]
  8. 7 Application and Implementation
    1. 7.1 Application Information,
    2. 7.2 Typical Application, CSI-2 Implementations
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Reset Implementation
      3. 7.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Receiving Notification of Documentation Updates
    2. 8.2 Support Resources
    3. 8.3 Trademarks
    4. 8.4 Electrostatic Discharge Caution
    5. 8.5 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.2.1 Design Requirements

Typically, in CSI-2 applications, the system trace length from the Camera (Source) to the DPHY440 device is different from that of the trace length from DPHY440 to the APU (Sink). Consequently, different pre-emphasis and equalization settings are required on the receiver and transmitter side of the device respectively.

For this design example, refer to Figure 7-1 and Figure 7-2. Shown is a CSI-2 system implementation in which the DPHY device is placed close to the Sink (APU). Here, the input trace length is about 12 inch while the output trace length is just 1 inch. The input signal characteristics assumed are shown in Table 7-1.

Table 7-1 Design Parameters
PARAMETERVALUE
Data Rate (200 Mbps to 1.5 Gbps)1 Gbps
Input trace length12 inch
Output trace length1 inch
Trace width10 mils