SLASF29A January   2022  – October 2024 TAA5242

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements: TDM, I2S or LJ Interface
    7. 5.7 Switching Characteristics: TDM, I2S or LJ Interface
    8. 5.8 Timing Diagrams
    9. 5.9 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Hardware Control
      2. 6.3.2 Audio Serial Interfaces
        1. 6.3.2.1 Time Division Multiplexed Audio (TDM) Interface
        2. 6.3.2.2 Inter IC Sound (I2S) Interface
        3. 6.3.2.3 Left-Justified (LJ) Interface
      3. 6.3.3 Phase-Locked Loop (PLL) and Clock Generation
      4. 6.3.4 Analog Input Configurations
      5. 6.3.5 Reference Voltage
      6. 6.3.6 Integrated Microphone Bias
      7. 6.3.7 Signal-Chain Processing
        1. 6.3.7.1 Configurable Digital Decimation Filters
          1. 6.3.7.1.1 Linear-phase filters
            1. 6.3.7.1.1.1 Sampling Rate: 8kHz or 7.35kHz
            2. 6.3.7.1.1.2 Sampling Rate: 16kHz or 14.7kHz
            3. 6.3.7.1.1.3 Sampling Rate: 24kHz or 22.05kHz
            4. 6.3.7.1.1.4 Sampling Rate: 32kHz or 29.4kHz
            5. 6.3.7.1.1.5 Sampling Rate: 48kHz or 44.1kHz
            6. 6.3.7.1.1.6 Sampling Rate: 96kHz or 88.2kHz
            7. 6.3.7.1.1.7 Sampling Rate: 192kHz or 176.4kHz
          2. 6.3.7.1.2 Low-latency Filters
            1. 6.3.7.1.2.1 Sampling Rate: 24kHz or 22.05kHz
            2. 6.3.7.1.2.2 Sampling Rate: 32kHz or 29.4kHz
            3. 6.3.7.1.2.3 Sampling Rate: 48kHz or 44.1kHz
            4. 6.3.7.1.2.4 Sampling Rate: 96kHz or 88.2kHz
            5. 6.3.7.1.2.5 Sampling Rate: 192kHz or 176.4kHz
        2. 6.3.7.2 Programmable Digital High-Pass Filter
    4. 6.4 Device Functional Modes
      1. 6.4.1 Active Mode
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Application
      2. 7.2.2 Design Requirements
      3. 7.2.3 Detailed Design Procedure
      4. 7.2.4 Application Performance Plots
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Documentation Support
      1. 8.1.1 Related Documentation
    2. 8.2 Receiving Notification of Documentation Updates
    3. 8.3 Support Resources
    4. 8.4 Trademarks
    5. 8.5 Electrostatic Discharge Caution
    6. 8.6 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.3 Power Supply Recommendations

The power supply sequence between the IOVDD and AVDD rails can be applied in any order. MD0 pin should be provided along with the power supplies and should be stable as soon as the supplies are settled to the recommended operating voltage levels. Only initiate the clocks to initialize the device after all the other Mode pins (MD1 to MD6) are also stable.

For the supply power-up requirement, t1, t2 and t3 must be at least 2ms to allow the device to initialize the internal settings. See the Section 6.3.1 section for details on how the device operates in various modes after the device power supplies are settled to the recommended operating voltage levels. For the supply power-down requirement, t4, t5 and t6 must be at least 10ms. This timing (as shown in Figure 7-4) allows the device to ramp down the volume on the record data, power down the analog and digital blocks, and put the device into a low power mode.

TAA5242 Power-Supply Sequencing Requirement Timing Diagram Figure 7-4 Power-Supply Sequencing Requirement Timing Diagram

Make sure that the supply ramp rate is slower than 0.1V/µs and that the wait time between a power-down and a power-up event is at least 100 ms.

The TAA5242 supports a single AVDD supply operation by integrating an on-chip digital regulator, DREG and integrated internal analog regulator.