SLASF24A December   2023  – January 2025 TAC5112

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Timing Requirements: I2C Interface
    7. 6.7  Switching Characteristics: I2C Interface
    8. 6.8  Timing Requirements: SPI Interface
    9. 6.9  Switching Characteristics: SPI Interface
    10. 6.10 Timing Requirements: TDM, I2S or LJ Interface
    11. 6.11 Switching Characteristics: TDM, I2S or LJ Interface
    12. 6.12 Timing Requirements: PDM Digital Microphone Interface
    13. 6.13 Switching Characteristics: PDM Digital Microphone Interface
    14. 6.14 Timing Diagrams
    15. 6.15 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Serial Interfaces
        1. 7.3.1.1 Control Serial Interfaces
        2. 7.3.1.2 Audio Serial Interfaces
          1. 7.3.1.2.1 Time Division Multiplexed Audio (TDM) Interface
          2. 7.3.1.2.2 Inter IC Sound (I2S) Interface
          3. 7.3.1.2.3 Left-Justified (LJ) Interface
        3. 7.3.1.3 Using Multiple Devices With Shared Buses
      2. 7.3.2  Phase-Locked Loop (PLL) and Clock Generation
      3. 7.3.3  Input Channel Configurations
      4. 7.3.4  Output Channel Configurations
      5. 7.3.5  Reference Voltage
      6. 7.3.6  Programmable Microphone Bias
      7. 7.3.7  Digital PDM Microphone Record Channel
      8. 7.3.8  Incremental ADC (IADC) Mode
      9. 7.3.9  Signal-Chain Processing
        1. 7.3.9.1 ADC Signal-Chain
          1. 7.3.9.1.1  6 to 4 Input Select Multiplexer (6:4 MUX)
          2. 7.3.9.1.2  Programmable Channel Gain and Digital Volume Control
          3. 7.3.9.1.3  Programmable Channel Gain Calibration
          4. 7.3.9.1.4  Programmable Channel Phase Calibration
          5. 7.3.9.1.5  Programmable Digital High-Pass Filter
          6. 7.3.9.1.6  Programmable Digital Biquad Filters
          7. 7.3.9.1.7  Programmable Channel Summer and Digital Mixer
          8. 7.3.9.1.8  Configurable Digital Decimation Filters
            1. 7.3.9.1.8.1 Linear-phase filters
              1. 7.3.9.1.8.1.1 Sampling Rate: 8kHz or 7.35kHz
              2. 7.3.9.1.8.1.2 Sampling Rate: 16kHz or 14.7kHz
              3. 7.3.9.1.8.1.3 Sampling Rate: 24kHz or 22.05kHz
              4. 7.3.9.1.8.1.4 Sampling Rate: 32kHz or 29.4kHz
              5. 7.3.9.1.8.1.5 Sampling Rate: 48kHz or 44.1kHz
              6. 7.3.9.1.8.1.6 Sampling Rate: 96kHz or 88.2kHz
              7. 7.3.9.1.8.1.7 Sampling Rate: 192kHz or 176.4kHz
            2. 7.3.9.1.8.2 Low-latency Filters
              1. 7.3.9.1.8.2.1 Sampling Rate: 24kHz or 22.05kHz
              2. 7.3.9.1.8.2.2 Sampling Rate: 32kHz or 29.4kHz
              3. 7.3.9.1.8.2.3 Sampling Rate: 48kHz or 44.1kHz
              4. 7.3.9.1.8.2.4 Sampling Rate: 96kHz or 88.2kHz
              5. 7.3.9.1.8.2.5 Sampling Rate: 192kHz or 176.4kHz
            3. 7.3.9.1.8.3 Ultra Low-latency Filters
              1. 7.3.9.1.8.3.1 Sampling Rate: 24kHz or 22.05kHz
              2. 7.3.9.1.8.3.2 Sampling Rate: 32kHz or 29.4kHz
              3. 7.3.9.1.8.3.3 Sampling Rate: 48kHz or 44.1kHz
              4. 7.3.9.1.8.3.4 Sampling Rate: 96kHz or 88.2kHz
              5. 7.3.9.1.8.3.5 Sampling Rate: 192kHz or 176.4kHz
          9. 7.3.9.1.9  Automatic Gain Controller (AGC)
          10. 7.3.9.1.10 Voice Activity Detection (VAD)
          11. 7.3.9.1.11 Ultrasonic Activity Detection (UAD)
        2. 7.3.9.2 DAC Signal-Chain
          1. 7.3.9.2.1 Programmable Channel Gain and Digital Volume Control
          2. 7.3.9.2.2 Programmable Channel Gain Calibration
          3. 7.3.9.2.3 Programmable Digital High-Pass Filter
          4. 7.3.9.2.4 Programmable Digital Biquad Filters
          5. 7.3.9.2.5 Programmable Digital Mixer
          6. 7.3.9.2.6 Configurable Digital Interpolation Filters
            1. 7.3.9.2.6.1 Linear-phase filters
              1. 7.3.9.2.6.1.1 Sampling Rate: 8kHz or 7.35kHz
              2. 7.3.9.2.6.1.2 Sampling Rate: 16kHz or 14.7kHz
              3. 7.3.9.2.6.1.3 Sampling Rate: 24kHz or 22.05kHz
              4. 7.3.9.2.6.1.4 Sampling Rate: 32kHz or 29.4kHz
              5. 7.3.9.2.6.1.5 Sampling Rate: 48kHz or 44.1kHz
              6. 7.3.9.2.6.1.6 Sampling Rate: 96kHz or 88.2kHz
              7. 7.3.9.2.6.1.7 Sampling Rate: 192kHz or 176.4kHz
              8. 7.3.9.2.6.1.8 Sampling Rate: 384kHz or 352.8kHz
              9. 7.3.9.2.6.1.9 Sampling Rate 768kHz or 705.6kHz
            2. 7.3.9.2.6.2 Low-latency Filters
              1. 7.3.9.2.6.2.1 Sampling Rate: 24kHz or 22.05kHz
              2. 7.3.9.2.6.2.2 Sampling Rate: 32kHz or 29.4kHz
              3. 7.3.9.2.6.2.3 Sampling Rate: 48kHz or 44.1kHz
              4. 7.3.9.2.6.2.4 Sampling Rate: 96kHz or 88.2kHz
              5. 7.3.9.2.6.2.5 Sampling Rate: 192kHz or 176.4kHz
            3. 7.3.9.2.6.3 Ultra-Low-Latency Filters
              1. 7.3.9.2.6.3.1 Sampling Rate: 24 kHz or 22.05 kHz
              2. 7.3.9.2.6.3.2 Sampling Rate: 32 kHz or 29.4 kHz
              3. 7.3.9.2.6.3.3 Sampling Rate: 48 kHz or 44.1 kHz
              4. 7.3.9.2.6.3.4 Sampling Rate: 96 kHz or 88.2 kHz
              5. 7.3.9.2.6.3.5 Sampling Rate 192 kHz or 176.4 kHz
      10. 7.3.10 Interrupts, Status, and Digital I/O Pin Multiplexing
      11. 7.3.11 Power Tune Mode
    4. 7.4 Device Functional Modes
      1. 7.4.1 Sleep Mode or Software Shutdown
      2. 7.4.2 Active Mode
      3. 7.4.3 Software Reset
    5. 7.5 Programming
      1. 7.5.1 Control Serial Interfaces
        1. 7.5.1.1 I2C Control Interface
          1. 7.5.1.1.1 General I2C Operation
          2. 7.5.1.1.2 I2C Single-Byte and Multiple-Byte Transfers
            1. 7.5.1.1.2.1 I2C Single-Byte Write
            2. 7.5.1.1.2.2 I2C Multiple-Byte Write
            3. 7.5.1.1.2.3 I2C Single-Byte Read
            4. 7.5.1.1.2.4 I2C Multiple-Byte Read
        2. 7.5.1.2 SPI Control Interface
  9. 8 Register Maps
    1. 8.1 Device Configuration Registers
      1. 8.1.1 Book0_P0 Registers
      2. 8.1.2 B0_P1 Registers
      3. 8.1.3 Book0_Page3 Registers
    2. 8.2 Programmable Coefficient Registers
      1. 8.2.1  Programmable Coefficient Registers: Page 8
      2. 8.2.2  Programmable Coefficient Registers: Page 9
      3. 8.2.3  Programmable Coefficient Registers: Page 10
      4. 8.2.4  Programmable Coefficient Registers: Page 11
      5. 8.2.5  Programmable Coefficient Registers: Page 15
      6. 8.2.6  Programmable Coefficient Registers: Page 16
      7. 8.2.7  Programmable Coefficient Registers: Page 17
      8. 8.2.8  Programmable Coefficient Registers: Page 18
      9. 8.2.9  Programmable Coefficient Registers: Page 19
      10. 8.2.10 Programmable Coefficient Registers: Page 25
      11. 8.2.11 Programmable Coefficient Registers: Page 26
      12. 8.2.12 Programmable Coefficient Registers: Page 27
      13. 8.2.13 Programmable Coefficient Registers: Page 28
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Application
      2. 9.2.2 Design Requirements
      3. 9.2.3 Detailed Design Procedure
      4. 9.2.4 Application Performance Plots
      5. 9.2.5 Example Device Register Configuration Script for EVM Setup
    3. 9.3 Power Supply Recommendations
      1. 9.3.1 AVDD_MODE for 1.8V Operation
      2. 9.3.2 IOVDD_IO_MODE for 1.8V and 1.2V Operation
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information
7.3.9.2.1 Programmable Channel Gain and Digital Volume Control

The device has an independent programmable channel gain setting for each output channel that can be set to the appropriate value based on the maximum input signal expected in the system, This can be done by configuring OUT1x_LVL_CTRL and OUT2x_LVL_CTRL bits. Coarse gain configuration from -12dB to +12dB is available with these controls in steps of 6dB.

The device has a programmable digital volume control with a range from –100dB to 27dB in steps of 0.5dB with the option to mute the channel recording. The digital volume control value can be changed dynamically while the DAC channel is powered-up and playing. During volume control changes, the soft ramp-up or ramp-down volume feature is used internally to avoid any audible artifacts. Soft-stepping can be entirely disabled using the DAC_DSP_DISABLE_SOFT_STEP (P0_R115_D[1]) register bit.

The digital volume control setting is independently available for each of the 4 single-ended output channels. In the case of 2-Channel Differential DAC, only settings for DAC_CH1A and DAC_CH2A are applicable. The device also supports an option to gang up the volume control setting for all channels together using the channel 1A digital volume control setting, regardless if channel 1A is powered up or powered down. This gang-up can be enabled using the DAC_DSP_DVOL_GANG (P0_R115_D[0]) register bit.

Table 7-44 shows the programmable options available for the digital volume control.

Table 7-44 Digital Volume Control (DVC) Programmable Settings
P0_R103_D[7:0] : DAC_CH1A_DVOL[7:0]DVC SETTING FOR OUTPUT CHANNEL 1A
0000 0000 = 0dOutput channel 1 DVC is set to mute
0000 0001 = 1dOutput channel 1 DVC is set to –100dB
0000 0010 = 2dOutput channel 1 DVC is set to –99.5dB
0000 0011 = 3dOutput channel 1 DVC is set to –99dB
……
1100 1000 = 200dOutput channel 1 DVC is set to –0.5dB
1100 1001 = 201d (default)Output channel 1 DVC is set to 0dB
1100 1010 = 202dOutput channel 1 DVC is set to 0.5dB
……
1111 1101 = 253dOutput channel 1 DVC is set to 26dB
1111 1110 = 254dOutput channel 1 DVC is set to 26.5dB
1111 1111 = 255dOutput channel 1 DVC is set to 27dB

Similarly, the digital volume control setting for output channels 1B, 2A, and 2B can be configured using the CH1B_DVOL (P0_R103) to CH2B_DVOL (P0_R112) register bits, respectively.

The internal digital processing engine soft ramps up the volume from a muted level to the programmed volume level when the channel is powered up, and the internal digital processing engine soft ramps down the volume from a programmed volume to mute when the channel is powered down. This soft-stepping of volume is done to prevent abruptly powering up and powering down the playback channel which can cause audible artifacts. This feature can also be entirely disabled using the DAC_DSP_DISABLE_SOFT_STEP (P0_R115_D[1]) register bit.