SLASF32A December   2023  – October 2024 TAD5142

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements: TDM, I2S or LJ Interface
    7. 5.7 Switching Characteristics: TDM, I2S or LJ Interface
    8. 5.8 Timing Diagrams
    9. 5.9 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Hardware Control
      2. 6.3.2 Audio Serial Interfaces
        1. 6.3.2.1 Time Division Multiplexed Audio (TDM) Interface
        2. 6.3.2.2 Inter IC Sound (I2S) Interface
        3. 6.3.2.3 Left-Justified (LJ) Interface
      3. 6.3.3 Phase-Locked Loop (PLL) and Clock Generation
      4. 6.3.4 Analog Output Configurations
      5. 6.3.5 Reference Voltage
      6. 6.3.6 DAC Signal-Chain
        1. 6.3.6.1 Digital Interpolation Filters
          1. 6.3.6.1.1 Linear-phase filters
            1. 6.3.6.1.1.1 Sampling Rate: 8kHz or 7.35kHz
            2. 6.3.6.1.1.2 Sampling Rate: 16kHz or 14.7kHz
            3. 6.3.6.1.1.3 Sampling Rate: 24kHz or 22.05kHz
            4. 6.3.6.1.1.4 Sampling Rate: 32kHz or 29.4kHz
            5. 6.3.6.1.1.5 Sampling Rate: 48kHz or 44.1kHz
            6. 6.3.6.1.1.6 Sampling Rate: 96kHz or 88.2kHz
            7. 6.3.6.1.1.7 Sampling Rate: 192kHz or 176.4kHz
          2. 6.3.6.1.2 Low-latency Filters
            1. 6.3.6.1.2.1 Sampling Rate: 24kHz or 22.05kHz
            2. 6.3.6.1.2.2 Sampling Rate: 32kHz or 29.4kHz
            3. 6.3.6.1.2.3 Sampling Rate: 48kHz or 44.1kHz
            4. 6.3.6.1.2.4 Sampling Rate: 96kHz or 88.2kHz
            5. 6.3.6.1.2.5 Sampling Rate: 192kHz or 176.4kHz
    4. 6.4 Device Functional Modes
      1. 6.4.1 Active Mode
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Application
      2. 7.2.2 Design Requirements
      3. 7.2.3 Detailed Design Procedure
      4. 7.2.4 Application Performance Plots
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Documentation Support
      1. 8.1.1 Related Documentation
    2. 8.2 Receiving Notification of Documentation Updates
    3. 8.3 Support Resources
    4. 8.4 Trademarks
    5. 8.5 Electrostatic Discharge Caution
    6. 8.6 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.2.3 Detailed Design Procedure

This section describes the necessary steps to configure the TAD5142 for this specific application.

  1. Audio serial interface (ASI) Mode is configured based on the MD0 pin setting which needs to be provided along with the power-supplies. Configure MD0 to be either pulled up to AVDD or down to VSS with appropriate resistor value. MD0 is configured to be grounded for this use case.
  2. Apply power to the device:
    1. Power up the IOVDD and AVDD power supplies.
    2. Ensure that MD0 pin setting is stable as soon as power supplies are up and wait for at least 2ms to allow the device to initialize the internal registers for this mode of operation.
    3. The device now is in sleep mode (low-power mode <1mA).
  3. Configure the Mode pins MD1 to MD6 as per the system requirements:
    1. Pull up to IOVDD or pull down to VSS on MD1 to MD6 pins as per the required configuration. All the pins are grounded for this use case.
  4. Apply the ASI Clocks (BCLK and FSYNC) to wake up the device.
  5. To put the device back in sleep mode, stop the clocks:
    1. Wait at least 100ms to allow the device to complete the shutdown sequence.
    2. Change the device mode configurations by changing MD1 to MD6 as per requirement.
  6. To change the ASI mode, re-configure MD0 pin and power-cycle the device.
  7. Repeat steps 1-6 as required for mode transitions.