SLLSFE3 December   2021 TCAN1164-Q1

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Device Comparison Table
  7. 7 Pin Configurations and Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 ESD Ratings IEC Specification
    4. 8.4 Recomended Operating Conditions
    5. 8.5 Thermal Information
    6. 8.6 Power Supply Characteristics
    7. 8.7 Electrical Characteristics
    8. 8.8 Switching Characteristics
    9. 8.9 Typical Characteristics
  9. 9 Parameter Measurement Information
  10. 10Detailed Description
    1. 10.1 Overview
    2. 10.2 Functional Block Diagram
    3. 10.3 Feature Description
      1. 10.3.1  VSUP Pin
      2. 10.3.2  VCCOUT Pin
      3. 10.3.3  Digital Inputs and Outputs
        1. 10.3.3.1 TXD Pin
        2. 10.3.3.2 RXD Pin
      4. 10.3.4  GND
      5. 10.3.5  nRST Pin
      6. 10.3.6  SDO
      7. 10.3.7  nCS Pin
      8. 10.3.8  SCLK
      9. 10.3.9  SDI
      10. 10.3.10 CAN Bus Pins
      11. 10.3.11 Local Faults
        1. 10.3.11.1 TXD Dominant Timeout (TXD DTO)
        2. 10.3.11.2 Thermal Shutdown (TSD)
        3. 10.3.11.3 Under/Over Voltage Lockout
        4. 10.3.11.4 Unpowered Devices
        5. 10.3.11.5 Floating Terminals
        6. 10.3.11.6 CAN Bus Short Circuit Current Limiting
        7. 10.3.11.7 Sleep Wake Error Timer
      12. 10.3.12 Watchdog
        1. 10.3.12.1 Watchdog Error Counter
        2. 10.3.12.2 Watchdog SPI Control Programming
        3. 10.3.12.3 Watchdog Timing
        4. 10.3.12.4 Question and Answer Watchdog
          1. 10.3.12.4.1 WD Question and Answer Basic information
          2. 10.3.12.4.2 Question and Answer Register and Settings
          3. 10.3.12.4.3 WD Question and Answer Value Generation
        5. 10.3.12.5 Question and Answer WD Example
          1. 10.3.12.5.1 Example configuration for desired behavior
          2. 10.3.12.5.2 Example of performing a question and answer sequence
      13. 10.3.13 Bus Fault Detection and Communication
    4. 10.4 Device Functional Modes
      1. 10.4.1 Operating Mode Description
        1. 10.4.1.1 Normal Mode
        2. 10.4.1.2 Silent Mode
        3. 10.4.1.3 Standby Mode
          1. 10.4.1.3.1 Wake-Up Pattern (WUP) Detection in Standby Mode
        4. 10.4.1.4 Reset Mode
        5. 10.4.1.5 Fail-safe Mode
      2. 10.4.2 CAN Transceiver
        1. 10.4.2.1 CAN Transceiver Operation
        2. 10.4.2.2 CAN Transceiver Modes
          1. 10.4.2.2.1 CAN Off Mode
          2. 10.4.2.2.2 CAN Autonomous: Inactive and Active
          3. 10.4.2.2.3 CAN Active
        3. 10.4.2.3 Driver and Receiver Function Tables
        4. 10.4.2.4 CAN Bus States
    5. 10.5 Programming
      1. 10.5.1 Serial Peripheral Interface (SPI) Communication
      2. 10.5.2 Serial Clock Input (SCLK)
      3. 10.5.3 Serial Data Input (SDI)
      4. 10.5.4 Serial Data Output (SDO)
      5. 10.5.5 Chip Select Not (nCS)
      6. 10.5.6 Registers
        1. 10.5.6.1  DEVICE_ID_y Register (Address = 0h + formula) [reset = xxh]
        2. 10.5.6.2  REV_ID_MAJOR Register (Address = 8h) [reset = 00h]
        3. 10.5.6.3  REV_ID_MINOR Register (Address = 9h) [reset = 00h]
        4. 10.5.6.4  SPI_RSVD_x Register (Address = Ah + formula) [reset = 00h]
        5. 10.5.6.5  Scratch_Pad_SPI Register (Address = Fh) [reset = 00h]
        6. 10.5.6.6  MODE_CNTRL Register (Address = 10h) [reset = 04h]
        7. 10.5.6.7  WD_CONFIG_1 Register (Address = 13h) [reset = 54h]
        8. 10.5.6.8  WD_CONFIG_2 Register (Address = 14h) [reset = 02h]
        9. 10.5.6.9  WD_INPUT_TRIG Register (Address = 15h) [reset = 00h]
        10. 10.5.6.10 WD_QA_CONFIG Register (Address = 2Dh) [reset = 0h]
        11. 10.5.6.11 WD_QA_ANSWER Register (Address = 2Eh) [reset = 0h]
        12. 10.5.6.12 WD_QA_QUESTION Register (Address = 2Fh) [reset = 0h]
        13. 10.5.6.13 STATUS (address = 40h) [reset = 00h]
        14. 10.5.6.14 INT_GLOBAL Register (Address = 50h) [reset = 0h]
        15. 10.5.6.15 INT_1 Register (Address = 51h) [reset = 0h]
        16. 10.5.6.16 INT_2 Register (Address = 52h) [reset = 40h]
        17. 10.5.6.17 INT_3 Register (Address 53h) [reset = 0h]
        18. 10.5.6.18 INT_CANBUS Register (Address = 54h) [reset = 0h]
        19. 10.5.6.19 INT_ENABLE_1 Register (Address = 56h) [reset = F3h]
        20. 10.5.6.20 INT_ENABLE_2 Register (Address = 57h) [reset = 3Fh]
        21. 10.5.6.21 INT_ENABLE_3 Register (Address =58h) [reset = 80h]
        22. 10.5.6.22 INT_ENABLE_CANBUS Register (Address = 59h) [reset = 7Fh]
        23. 10.5.6.23 INT_RSVD_y Register (Address = 5Ah + formula) [reset = 00h]
  11. 11Application Information Disclaimer
    1. 11.1 Application Information
    2. 11.2 Typical Application
      1. 11.2.1 Design Requirements
        1. 11.2.1.1 Bus Loading, Length and Number of Nodes
      2. 11.2.2 Detailed Design Procedures
        1. 11.2.2.1 CAN Termination
    3. 11.3 Application Curves
  12. 12Power Supply Requirements
  13. 13Layout
    1. 13.1 Layout Guidelines
    2. 13.2 Layout Example
  14. 14Device and Documentation Support
    1. 14.1 Documentation Support
      1. 14.1.1 Related Documentation
    2. 14.2 Receiving Notification of Documentation Updates
    3. 14.3 Support Resources
    4. 14.4 Trademarks
    5. 14.5 Electrostatic Discharge Caution
    6. 14.6 Glossary
  15. 15Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.3 ESD Ratings IEC Specification

VALUE UNIT
VESD System level electro-static discharge (ESD)(1) CAN bus terminals (CANH & CANL) to GND IEC 61000-4-2 (150pF, 330Ω) unpowered contact discharge ±8000 V
VSUP ±8000
VTRAN ISO 7637 ISO pulse transients(2) CAN bus terminals (CANH & CANL) to GND, VSUP Pulse 1 –100
Pulse 2 75
Pulse 3a –150
Pulse 3b 100
ISO 7637-3 transient(3) DCC slow transient pulse ±30
(1) Tested according to IEC 62228-3 CAN Transceiver, Section 6.4; DIN EN 61000-4-2
(2) Tested according to IEC 62228-3 CAN Transceiver, Section 6.3; standard pulse parameters defined in ISO 7637-2
(3) Tested according to ISO 7637-3; electrical transient transmission by capacitive and inductive coupling via lines other than supply line