SBOSA41A May   2023  – September 2023 TMP4718

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 I2C Interface Timing
    7. 7.7 Timing Diagrams
    8. 7.8 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 1.2-V Logic Compatible Inputs
      2. 8.3.2 Series Resistance Cancellation
      3. 8.3.3 Device Initialization, Resistor Decoding, and Default Temperature Conversion
      4. 8.3.4 Adjustable Default T_CRIT High-Temperature Limit
      5. 8.3.5 ALERT and T_CRIT Output
      6. 8.3.6 Fault Queue
      7. 8.3.7 Filtering
      8. 8.3.8 One-Shot Conversions
    4. 8.4 Device Functional Modes
      1. 8.4.1 Interrupt and Comparator Mode
        1. 8.4.1.1 Interrupt Mode
        2. 8.4.1.2 Comparator Mode
        3. 8.4.1.3 T_CRIT Output
      2. 8.4.2 Shutdown Mode
      3. 8.4.3 Continuous Conversion Mode
    5. 8.5 Programming
      1. 8.5.1 Temperature Data Format
      2. 8.5.2 I2C and SMBus Interface
      3. 8.5.3 Device Address
      4. 8.5.4 Bus Transactions
        1. 8.5.4.1 Writes
        2. 8.5.4.2 Reads
      5. 8.5.5 SMBus Alert Mode
    6. 8.6 Register Map
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.3.5 ALERT and T_CRIT Output

The TMP4718 ALERT and T_CRIT pins are active-low open drain outputs. The ALERT pin is asserted at the end of a conversion cycle when the measured temperature exceeds a High Alert Limit or goes below a Low Alert Limit. The T_CRIT pin is asserted at the end of a conversion cycle when the measured temperature exceeds the T_CRIT limit defined in the limit register. The ALERT and T_CRIT pins can be used to notify the system of overtemperature or undertemperature conditions and protect from thermally induced system damages. Note the ALERT and T_CRIT outputs are activated only when the corresponding bits are configured in the Alert_Mask register.