SPRSP69B July   2023  – November 2023 TMS320F28P650DK , TMS320F28P659DK-Q1

PRODMIX  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
    1. 3.1 Functional Block Diagram
  5. 4 Device Comparison
    1. 4.1 Related Products
  6. 5 Pin Configuration and Functions
    1. 5.1 Pin Diagrams
    2. 5.2 Pin Attributes
    3. 5.3 Signal Descriptions
      1. 5.3.1 Analog Signals
      2. 5.3.2 Digital Signals
      3. 5.3.3 Power and Ground
      4. 5.3.4 Test, JTAG, and Reset
    4. 5.4 Pins With Internal Pullup and Pulldown
    5. 5.5 Pin Multiplexing
      1. 5.5.1 GPIO Muxed Pins
      2. 5.5.2 USB Pin Muxing
      3. 5.5.3 High-Speed SPI Pin Muxing
    6. 5.6 Connections for Unused Pins
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings – Commercial
    3. 6.3  ESD Ratings – Automotive
    4. 6.4  Recommended Operating Conditions
    5. 6.5  Power Consumption Summary
      1. 6.5.1 System Current Consumption VREG Enabled
      2. 6.5.2 System Current Consumption VREG Disable - External Supply
      3. 6.5.3 Operating Mode Test Description
      4. 6.5.4 Current Consumption Graphs
      5. 6.5.5 Reducing Current Consumption
        1. 6.5.5.1 Typical Current Reduction per Disabled Peripheral
    6. 6.6  Electrical Characteristics
    7. 6.7  Thermal Resistance Characteristics for ZEJ Package
    8. 6.8  Thermal Resistance Characteristics for PTP Package
    9. 6.9  Thermal Resistance Characteristics for NMR Package
    10. 6.10 Thermal Resistance Characteristics for PZP Package
    11. 6.11 Thermal Design Considerations
    12. 6.12 System
      1. 6.12.1  Power Management Module (PMM)
        1. 6.12.1.1 Introduction
        2. 6.12.1.2 Overview
          1. 6.12.1.2.1 Power Rail Monitors
            1. 6.12.1.2.1.1 I/O POR (Power-On Reset) Monitor
            2. 6.12.1.2.1.2 I/O BOR (Brown-Out Reset) Monitor
            3. 6.12.1.2.1.3 VDD POR (Power-On Reset) Monitor
          2. 6.12.1.2.2 External Supervisor Usage
          3. 6.12.1.2.3 Delay Blocks
          4. 6.12.1.2.4 Internal 1.2-V LDO Voltage Regulator (VREG)
          5. 6.12.1.2.5 VREGENZ
        3. 6.12.1.3 External Components
          1. 6.12.1.3.1 Decoupling Capacitors
            1. 6.12.1.3.1.1 VDDIO Decoupling
            2. 6.12.1.3.1.2 VDD Decoupling
        4. 6.12.1.4 Power Sequencing
          1. 6.12.1.4.1 Supply Pins Ganging
          2. 6.12.1.4.2 Signal Pins Power Sequence
          3. 6.12.1.4.3 Supply Pins Power Sequence
            1. 6.12.1.4.3.1 External VREG/VDD Mode Sequence
            2. 6.12.1.4.3.2 Internal VREG/VDD Mode Sequence
            3. 6.12.1.4.3.3 Supply Sequencing Summary and Effects of Violations
            4. 6.12.1.4.3.4 Supply Slew Rate
        5. 6.12.1.5 Power Management Module Electrical Data and Timing
          1. 6.12.1.5.1 Power Management Module Operating Conditions
          2. 6.12.1.5.2 Power Management Module Characteristics
      2. 6.12.2  Reset Timing
        1. 6.12.2.1 Reset Sources
        2. 6.12.2.2 Reset Electrical Data and Timing
          1. 6.12.2.2.1 Reset XRSn Timing Requirements
          2. 6.12.2.2.2 Reset XRSn Switching Characteristics
          3. 6.12.2.2.3 Reset Timing Diagrams
      3. 6.12.3  Clock Specifications
        1. 6.12.3.1 Clock Sources
        2. 6.12.3.2 Clock Frequencies, Requirements, and Characteristics
          1. 6.12.3.2.1 Input Clock Frequency and Timing Requirements, PLL Lock Times
            1. 6.12.3.2.1.1 Input Clock Frequency
            2. 6.12.3.2.1.2 XTAL Oscillator Characteristics
            3. 6.12.3.2.1.3 X1 Input Level Characteristics When Using an External Clock Source Not a Crystal
            4. 6.12.3.2.1.4 X1 Timing Requirements
            5. 6.12.3.2.1.5 AUXCLKIN Timing Requirements
            6. 6.12.3.2.1.6 APLL Characteristics
            7. 6.12.3.2.1.7 XCLKOUT Switching Characteristics PLL Bypassed or Enabled
            8. 6.12.3.2.1.8 Internal Clock Frequencies
        3. 6.12.3.3 Input Clocks
        4. 6.12.3.4 XTAL Oscillator
          1. 6.12.3.4.1 Introduction
          2. 6.12.3.4.2 Overview
            1. 6.12.3.4.2.1 Electrical Oscillator
              1. 6.12.3.4.2.1.1 Modes of Operation
                1. 6.12.3.4.2.1.1.1 Crystal Mode of Operation
                2. 6.12.3.4.2.1.1.2 Single-Ended Mode of Operation
              2. 6.12.3.4.2.1.2 XTAL Output on XCLKOUT
            2. 6.12.3.4.2.2 Quartz Crystal
            3. 6.12.3.4.2.3 GPIO Modes of Operation
          3. 6.12.3.4.3 Functional Operation
            1. 6.12.3.4.3.1 ESR – Effective Series Resistance
            2. 6.12.3.4.3.2 Rneg – Negative Resistance
            3. 6.12.3.4.3.3 Start-up Time
            4. 6.12.3.4.3.4 DL – Drive Level
          4. 6.12.3.4.4 How to Choose a Crystal
          5. 6.12.3.4.5 Testing
          6. 6.12.3.4.6 Common Problems and Debug Tips
          7. 6.12.3.4.7 Crystal Oscillator Specifications
            1. 6.12.3.4.7.1 Crystal Oscillator Electrical Characteristics
            2. 6.12.3.4.7.2 Crystal Equivalent Series Resistance (ESR) Requirements
            3. 6.12.3.4.7.3 Crystal Oscillator Parameters
            4. 6.12.3.4.7.4 Crystal Oscillator Electrical Characteristics
        5. 6.12.3.5 Internal Oscillators
          1. 6.12.3.5.1 INTOSC Characteristics
      4. 6.12.4  Flash Parameters
        1. 6.12.4.1 Flash Parameters 
      5. 6.12.5  RAM Specifications
      6. 6.12.6  ROM Specifications
      7. 6.12.7  Emulation/JTAG
        1. 6.12.7.1 JTAG Electrical Data and Timing
          1. 6.12.7.1.1 JTAG Timing Requirements
          2. 6.12.7.1.2 JTAG Switching Characteristics
          3. 6.12.7.1.3 JTAG Timing Diagram
        2. 6.12.7.2 cJTAG Electrical Data and Timing
          1. 6.12.7.2.1 cJTAG Timing Requirements
          2. 6.12.7.2.2 cJTAG Switching Characteristics
          3. 6.12.7.2.3 cJTAG Timing Diagram
      8. 6.12.8  GPIO Electrical Data and Timing
        1. 6.12.8.1 GPIO – Output Timing
          1. 6.12.8.1.1 General-Purpose Output Switching Characteristics
          2. 6.12.8.1.2 General-Purpose Output Timing Diagram
        2. 6.12.8.2 GPIO – Input Timing
          1. 6.12.8.2.1 General-Purpose Input Timing Requirements
          2. 6.12.8.2.2 Sampling Mode
        3. 6.12.8.3 Sampling Window Width for Input Signals
      9. 6.12.9  Interrupts
        1. 6.12.9.1 External Interrupt (XINT) Electrical Data and Timing
          1. 6.12.9.1.1 External Interrupt Timing Requirements
          2. 6.12.9.1.2 External Interrupt Switching Characteristics
          3. 6.12.9.1.3 External Interrupt Timing
      10. 6.12.10 Low-Power Modes
        1. 6.12.10.1 Clock-Gating Low-Power Modes
        2. 6.12.10.2 Low-Power Mode Wake-up Timing
          1. 6.12.10.2.1 IDLE Mode Timing Requirements
          2. 6.12.10.2.2 IDLE Mode Switching Characteristics
          3. 6.12.10.2.3 IDLE Entry and Exit Timing Diagram
          4. 6.12.10.2.4 STANDBY Mode Timing Requirements
          5. 6.12.10.2.5 STANDBY Mode Switching Characteristics
          6. 6.12.10.2.6 STANDBY Entry and Exit Timing Diagram
          7. 6.12.10.2.7 HALT Mode Timing Requirements
          8. 6.12.10.2.8 HALT Mode Switching Characteristics
          9. 6.12.10.2.9 HALT Entry and Exit Timing Diagram
      11. 6.12.11 External Memory Interface (EMIF)
        1. 6.12.11.1 Asynchronous Memory Support
        2. 6.12.11.2 Synchronous DRAM Support
        3. 6.12.11.3 EMIF Electrical Data and Timing
          1. 6.12.11.3.1 EMIF Synchronous Memory Timing Requirements
          2. 6.12.11.3.2 EMIF Synchronous Memory Switching Characteristics
          3. 6.12.11.3.3 EMIF Synchronous Memory Timing Diagrams
          4. 6.12.11.3.4 EMIF Asynchronous Memory Timing Requirements
          5. 6.12.11.3.5 EMIF Asynchronous Memory Switching Characteristics
          6. 6.12.11.3.6 EMIF Asynchronous Memory Timing Diagrams
    13. 6.13 C28x Analog Peripherals
      1. 6.13.1 Analog Subsystem
        1. 6.13.1.1 Features
        2. 6.13.1.2 Block Diagram
      2. 6.13.2 Analog-to-Digital Converter (ADC)
        1. 6.13.2.1 ADC Configurability
          1. 6.13.2.1.1 Signal Mode
        2. 6.13.2.2 ADC Electrical Data and Timing
          1. 6.13.2.2.1  ADC Operating Conditions 12-bit Single-Ended
          2. 6.13.2.2.2  ADC Operating Conditions 12-bit Differential
          3. 6.13.2.2.3  ADC Operating Conditions 16-bit Single-Ended
          4. 6.13.2.2.4  ADC Operating Conditions 16-bit Differential
          5. 6.13.2.2.5  ADC Characteristics 12-bit Single-Ended
          6. 6.13.2.2.6  ADC Characteristics 12-bit Differential
          7. 6.13.2.2.7  ADC Characteristics 16-bit Single-Ended
          8. 6.13.2.2.8  ADC Characteristics 16-bit Differential
          9. 6.13.2.2.9  ADC Performance Per Pin
          10. 6.13.2.2.10 ADC Input Models
          11. 6.13.2.2.11 ADC Timing Diagrams
      3. 6.13.3 Temperature Sensor
        1. 6.13.3.1 Temperature Sensor Electrical Data and Timing
          1. 6.13.3.1.1 Temperature Sensor Characteristics
      4. 6.13.4 Comparator Subsystem (CMPSS)
        1. 6.13.4.1 CMPSS Connectivity Diagram
        2. 6.13.4.2 Block Diagram
        3. 6.13.4.3 CMPSS Electrical Data and Timing
          1. 6.13.4.3.1 Comparator Electrical Characteristics
          2.        CMPSS Comparator Input Referred Offset and Hysteresis
          3. 6.13.4.3.2 CMPSS DAC Static Electrical Characteristics
          4. 6.13.4.3.3 CMPSS Illustrative Graphs
          5. 6.13.4.3.4 CMPSS DAC Dynamic Error
      5. 6.13.5 Buffered Digital-to-Analog Converter (DAC)
        1. 6.13.5.1 Buffered DAC Electrical Data and Timing
          1. 6.13.5.1.1 Buffered DAC Operating Conditions
          2. 6.13.5.1.2 Buffered DAC Electrical Characteristics
    14. 6.14 C28x Control Peripherals
      1. 6.14.1 Enhanced Capture (eCAP)
        1. 6.14.1.1 eCAP Block Diagram
        2. 6.14.1.2 eCAP Synchronization
        3. 6.14.1.3 eCAP Electrical Data and Timing
          1. 6.14.1.3.1 eCAP Timing Requirements
          2. 6.14.1.3.2 eCAP Switching Characteristics
      2. 6.14.2 High-Resolution Capture (HRCAP)
        1. 6.14.2.1 eCAP and HRCAP Block Diagram
        2. 6.14.2.2 HRCAP Electrical Data and Timing
          1. 6.14.2.2.1 HRCAP Switching Characteristics
          2. 6.14.2.2.2 HRCAP Figure and Graph
      3. 6.14.3 Enhanced Pulse Width Modulator (ePWM)
        1. 6.14.3.1 Control Peripherals Synchronization
        2. 6.14.3.2 ePWM Electrical Data and Timing
          1. 6.14.3.2.1 ePWM Timing Requirements
          2. 6.14.3.2.2 ePWM Switching Characteristics
          3. 6.14.3.2.3 Trip-Zone Input Timing
            1. 6.14.3.2.3.1 Trip-Zone Input Timing Requirements
            2. 6.14.3.2.3.2 PWM Hi-Z Characteristics Timing Diagram
      4. 6.14.4 External ADC Start-of-Conversion Electrical Data and Timing
        1. 6.14.4.1 External ADC Start-of-Conversion Switching Characteristics
        2. 6.14.4.2 ADCSOCAO or ADCSOCBO Timing Diagram
      5. 6.14.5 High-Resolution Pulse Width Modulator (HRPWM)
        1. 6.14.5.1 HRPWM Electrical Data and Timing
          1. 6.14.5.1.1 High-Resolution PWM Characteristics
      6. 6.14.6 Enhanced Quadrature Encoder Pulse (eQEP)
        1. 6.14.6.1 eQEP Electrical Data and Timing
          1. 6.14.6.1.1 eQEP Timing Requirements
          2. 6.14.6.1.2 eQEP Switching Characteristics
      7. 6.14.7 Sigma-Delta Filter Module (SDFM)
        1. 6.14.7.1 SDFM Electrical Data and Timing
          1. 6.14.7.1.1 SDFM Timing Requirements When Using Asynchronous GPIO ASYNC Option
    15. 6.15 C28x Communications Peripherals
      1. 6.15.1  Controller Area Network (CAN)
      2. 6.15.2  Modular Controller Area Network (MCAN)
      3. 6.15.3  Fast Serial Interface (FSI)
        1. 6.15.3.1 FSI Transmitter
          1. 6.15.3.1.1 FSITX Electrical Data and Timing
            1. 6.15.3.1.1.1 FSITX Switching Characteristics
            2. 6.15.3.1.1.2 FSITX Timings
        2. 6.15.3.2 FSI Receiver
          1. 6.15.3.2.1 FSIRX Electrical Data and Timing
            1. 6.15.3.2.1.1 FSIRX Timing Requirements
            2. 6.15.3.2.1.2 FSIRX Switching Characteristics
            3. 6.15.3.2.1.3 FSIRX Timings
        3. 6.15.3.3 FSI SPI Compatibility Mode
          1. 6.15.3.3.1 FSITX SPI Signaling Mode Electrical Data and Timing
            1. 6.15.3.3.1.1 FSITX SPI Signaling Mode Switching Characteristics
            2. 6.15.3.3.1.2 FSITX SPI Signaling Mode Timings
      4. 6.15.4  Inter-Integrated Circuit (I2C)
        1. 6.15.4.1 I2C Electrical Data and Timing
          1. 6.15.4.1.1 I2C Timing Requirements
          2. 6.15.4.1.2 I2C Switching Characteristics
          3. 6.15.4.1.3 I2C Timing Diagram
      5. 6.15.5  Power Management Bus (PMBus) Interface
        1. 6.15.5.1 PMBus Electrical Data and Timing
          1. 6.15.5.1.1 PMBus Electrical Characteristics
          2. 6.15.5.1.2 PMBus Fast Mode Switching Characteristics
          3. 6.15.5.1.3 PMBus Standard Mode Switching Characteristics
      6. 6.15.6  Serial Communications Interface (SCI)
      7. 6.15.7  Serial Peripheral Interface (SPI)
        1. 6.15.7.1 SPI Controller Mode Timings
          1. 6.15.7.1.1 SPI Controller Mode Switching Characteristics Clock Phase 0
          2. 6.15.7.1.2 SPI Controller Mode Switching Characteristics Clock Phase 1
          3. 6.15.7.1.3 SPI Controller Mode Timing Requirements
          4. 6.15.7.1.4 SPI Controller Mode Timing Diagrams
        2. 6.15.7.2 SPI Peripheral Mode Timings
          1. 6.15.7.2.1 SPI Peripheral Mode Switching Characteristics
          2. 6.15.7.2.2 SPI Peripheral Mode Timing Requirements
          3. 6.15.7.2.3 SPI Peripheral Mode Timing Diagrams
      8. 6.15.8  Local Interconnect Network (LIN)
      9. 6.15.9  EtherCAT SubordinateDevice Controller (ESC)
        1. 6.15.9.1 ESC Features
        2. 6.15.9.2 ESC Subsystem Integrated Features
        3. 6.15.9.3 EtherCAT IP Block Diagram
        4. 6.15.9.4 EtherCAT Electrical Data and Timing
          1. 6.15.9.4.1 EtherCAT Timing Requirements
          2. 6.15.9.4.2 EtherCAT Switching Characteristics
          3. 6.15.9.4.3 EtherCAT Timing Diagrams
      10. 6.15.10 Universal Serial Bus (USB)
        1. 6.15.10.1 USB Electrical Data and Timing
          1. 6.15.10.1.1 USB Input Ports DP and DM Timing Requirements
          2. 6.15.10.1.2 USB Output Ports DP and DM Switching Characteristics
      11. 6.15.11 Universal Asynchronous Receiver-Transmitter (UART)
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Memory
      1. 7.3.1 C28x Memory Map
      2. 7.3.2 Control Law Accelerator (CLA) Memory Map
      3. 7.3.3 Flash Memory Map
        1. 7.3.3.1 Addresses of Flash Sectors
      4. 7.3.4 EMIF Chip Select Memory Map
      5. 7.3.5 Peripheral Registers Memory Map
      6. 7.3.6 Memory Types
        1. 7.3.6.1 Dedicated RAM (Mx and Dx RAM)
        2. 7.3.6.2 Local Shared RAM (LSx RAM)
        3. 7.3.6.3 Global Shared RAM (GSx RAM)
        4. 7.3.6.4 CPU Message RAM (CPU MSGRAM)
        5. 7.3.6.5 CLA Message RAM (CLA MSGRAM)
        6. 7.3.6.6 CLA - DMA Message RAM (CLA-DMA MSGRAM)
    4. 7.4 Identification
    5. 7.5 Bus Architecture – Peripheral Connectivity
    6. 7.6 Boot ROM
      1. 7.6.1 Device Boot
      2. 7.6.2 Device Boot Modes
      3. 7.6.3 Device Boot Configurations
      4. 7.6.4 GPIO Assignments
    7. 7.7 Security
      1. 7.7.1 Securing the Boundary of the Chip
        1. 7.7.1.1 JTAGLOCK
        2. 7.7.1.2 Zero-pin Boot
      2. 7.7.2 Dual-Zone Security
      3. 7.7.3 Disclaimer
    8. 7.8 Advanced Encryption Standard (AES) Accelerator
    9. 7.9 C28x (CPU1/CPU2) Subsystem
      1. 7.9.1  C28x Processor
        1. 7.9.1.1 Floating-Point Unit (FPU)
        2. 7.9.1.2 Fast Integer Division Unit
        3. 7.9.1.3 Trigonometric Math Unit (TMU)
        4. 7.9.1.4 VCRC Unit
        5. 7.9.1.5 Lockstep Compare Module (LCM)
      2. 7.9.2  Control Law Accelerator (CLA)
      3. 7.9.3  Embedded Real-Time Analysis and Diagnostic (ERAD)
      4. 7.9.4  Background CRC-32 (BGCRC)
      5. 7.9.5  Direct Memory Access (DMA)
      6. 7.9.6  Interprocessor Communication (IPC) Module
      7. 7.9.7  C28x Timers
      8. 7.9.8  Dual-Clock Comparator (DCC)
        1. 7.9.8.1 Features
        2. 7.9.8.2 Mapping of DCCx Clock Source Inputs
      9. 7.9.9  Nonmaskable Interrupt With Watchdog Timer (NMIWD)
      10. 7.9.10 Watchdog
      11. 7.9.11 Configurable Logic Block (CLB)
  9. 8 Applications, Implementation, and Layout
    1. 8.1 Application and Implementation
    2. 8.2 Key Device Features
    3. 8.3 Application Information
      1. 8.3.1 Typical Application
        1. 8.3.1.1 Servo Drive Control Module
          1. 8.3.1.1.1 System Block Diagram
          2. 8.3.1.1.2 Servo Drive Control Module Resources
        2. 8.3.1.2 Solar Micro Inverter
          1. 8.3.1.2.1 System Block Diagram
          2. 8.3.1.2.2 Solar Micro Inverter Resources
        3. 8.3.1.3 EV Charging Station Power Module
          1. 8.3.1.3.1 System Block Diagram
          2. 8.3.1.3.2 EV Charging Station Power Module Resources
        4. 8.3.1.4 On-Board Charger (OBC)
          1. 8.3.1.4.1 System Block Diagram
          2. 8.3.1.4.2 OBC Resources
        5. 8.3.1.5 High-Voltage Traction Inverter
          1. 8.3.1.5.1 System Block Diagram
          2. 8.3.1.5.2 High-Voltage Traction Inverter Resources
  10. 9 Device and Documentation Support
    1. 9.1 Getting Started and Next Steps
    2. 9.2 Device Nomenclature
    3. 9.3 Markings
    4. 9.4 Tools and Software
    5. 9.5 Documentation Support
    6. 9.6 Support Resources
    7. 9.7 Trademarks
    8. 9.8 Electrostatic Discharge Caution
    9. 9.9 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • PZP|100
Thermal pad, mechanical data (Package|Pins)
Orderable Information

3 Description

The TMS320F28P65x (F28P65x) is a member of the C2000™ real-time microcontroller family of scalable, ultra-low latency devices designed for efficiency in power electronics, including but not limited to: high power density, high switching frequencies, and supporting the use of IGBT, GaN, and SiC technologies.

These include such applications as:

The real-time control subsystem is based on TI’s 32-bit C28x DSP core, which provides 200 MIPS of signal-processing performance in each core for floating- or fixed-point code running from either on-chip flash or SRAM. This is equivalent to the 400-MHz processing power on a Cortex®-M7 based device (C28x DSP core gives two times more performance than the Cortex®-M7 core).The C28x CPU is further boosted by the Trigonometric Math Unit (TMU) and VCRC (Cyclical Redundancy Check) extended instruction sets, speeding up common algorithms key to real-time control systems. Extended instruction sets enable IEEE double-precision 64-bit floating-point math. Finally, the Control Law Accelerator (CLA) enables an additional 200 MIPS per core of independent processing ability. This is equivalent to the 280-MHz processing power on a Cortex®-M7 based device (CLA CPU gives 40% more performance than the Cortex®-M7 core).

The lockstep dual-CPU comparator option has been added in the secondary C28x CPU along with ePIE and DMA for detection of permanent and transient faults. To allow fast context switching from existing to new firmware, hardware enhancements for Live Firmware Update (LFU) have been added to F28P65x.

High-performance analog blocks are tightly integrated with the processing and control units to provide optimal real-time signal chain performance. The Analog-to-Digital Converter (ADC) has been enhanced with up to 40 analog channels, 22 of which have general-purpose input/output (GPIO) capability. Implementation of oversampling is greatly simplified with hardware improvement. For safety-critical ADC conversions, a hardware redundancy checker has been added that provides the ability to compare ADC conversion results from multiple ADC modules for consistency without additional CPU cycles. Thirty-six frequency-independent PWMs, all with high-resolution capability, enable control of multiple power stages, from 3-phase inverters to advanced multilevel power topologies. The PWMs have been enhanced with Minimum Dead-Band Logic (MINDL) and Illegal Combo Logic (ICL) features.

The inclusion of the Configurable Logic Block (CLB) allows the user to add custom logic and potentially integrate FPGA-like functions into the C2000 real-time MCU.

An EtherCAT SubDevice Controller and other industry-standard protocols like CAN FD and USB 2.0 are available on this device. The Fast Serial Interface (FSI) enables up to 200 Mbps of robust communications across an isolation boundary.

As a highly connected device, the F28P65x also offers various security enablers to help designers implement their cyber security strategy and support features like hardware encryption, secure JTAG and secure Boot.

From a safety standpoint, F28P65x supports numerous safety enablers. For more details, see Industrial Functional Safety for C2000™ Real-Time Microcontrollers and Automotive Functional Safety for C2000™ Real-Time Microcontrollers.

Want to learn more about features that make C2000 MCUs the right choice for your real-time control system? Check out The Essential Guide for Developing With C2000™ Real-Time Microcontrollers and visit the C2000™ real-time control MCUs page.

The Getting Started With C2000™ Real-Time Control Microcontrollers (MCUs) Getting Started Guide covers all aspects of development with C2000 devices from hardware to support resources. In addition to key reference documents, each section provides relevant links and resources to further expand on the information covered.

Ready to get started? Check out the TMDSCNCD28P65X evaluation board and download C2000Ware.

Device Information
PART NUMBER(1) PACKAGE(2) PACKAGE SIZE(3) PROCESSORS EtherCAT® LOCKSTEP FLASH SIZE
TMS320F28P650DK9 ZEJ (nFBGA, 256) 13 mm x 13 mm CPU1+CLA, CPU2 Yes Yes 1.28MB
NMR (nFBGA, 169) 9 mm x 9 mm
PTP (HLQFP, 176) 26 mm x 26 mm
TMS320F28P650DK8(4) ZEJ (nFBGA, 256) 13 mm x 13 mm CPU1+CLA, CPU2 – Yes
NMR (nFBGA, 169) 9 mm x 9 mm
PTP (HLQFP, 176) 26 mm x 26 mm
TMS320F28P650DK7(4) ZEJ (nFBGA, 256) 13 mm x 13 mm CPU1+CLA, CPU2 Yes –
NMR (nFBGA, 169) 9 mm x 9 mm
PTP (HLQFP, 176) 26 mm x 26 mm
TMS320F28P650SK7(4) ZEJ (nFBGA, 256) 13 mm x 13 mm CPU1+CLA Yes –
NMR (nFBGA, 169) 9 mm x 9 mm
PTP (HLQFP, 176) 26 mm x 26 mm
TMS320F28P659DK8-Q1(4) ZEJ (nFBGA, 256) 13 mm x 13 mm CPU1+CLA, CPU2 – Yes
PTP (HLQFP, 176) 26 mm x 26 mm
PZP (HTQFP, 100) 16 mm x 16 mm
TMS320F28P650DK6 ZEJ (nFBGA, 256) 13 mm x 13 mm CPU1+CLA, CPU2 – –
NMR (nFBGA, 169) 9 mm x 9 mm
PTP (HLQFP, 176) 26 mm x 26 mm
PZP (HTQFP, 100) 16 mm x 16 mm
TMS320F28P650SK6(4) ZEJ (nFBGA, 256) 13 mm x 13 mm CPU1+CLA – –
NMR (nFBGA, 169) 9 mm x 9 mm
PTP (HLQFP, 176) 26 mm x 26 mm
PZP (HTQFP, 100) 16 mm x 16 mm
TMS320F28P659DH8-Q1(4) PZP (HTQFP, 100) 16 mm x 16 mm CPU1+CLA, CPU2 – Yes 768KB
TMS320F28P659SH6-Q1(4) PTP (HLQFP, 176) 26 mm x 26 mm CPU1+CLA – –
PZP (HTQFP, 100) 16 mm x 16 mm
TMS320F28P650DH6(4) PZP (HTQFP, 100) 16 mm x 16 mm CPU1+CLA, CPU2 – –
TMS320F28P650SH7(4) NMR (nFBGA, 169) 9 mm x 9 mm CPU1+CLA Yes –
PTP (HLQFP, 176) 26 mm x 26 mm
TMS320F28P650SH6(4) NMR (nFBGA, 169) 9 mm x 9 mm CPU1+CLA – –
PTP (HLQFP, 176) 26 mm x 26 mm
PZP (HTQFP, 100) 16 mm x 16 mm
(1) For more information on these devices, see the Device Comparison table.
(2) For more information, see the Mechanical, Packaging, and Orderable Information section.
(3) The package size (length x width) is a nominal value and includes pins, where applicable.
(4) Preview information (not Production Data).