SLOS810A October   2019  – August 2020 TPA3139D2

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics,
      1. 6.7.1 Bridge -Tied Load (BTL)
      2. 6.7.2 Paralleled Bridge -Tied Load (PBTL)
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Analog Gain
      2. 7.3.2  SD/ FAULT and MUTE Operation
      3. 7.3.3  PLIMIT
      4. 7.3.4  Spread Spectrum and De-Phase Control
      5. 7.3.5  GVDD Supply
      6. 7.3.6  DC Detect
      7. 7.3.7  PBTL Select
      8. 7.3.8  Short-Circuit Protection and Automatic Recovery Feature
      9. 7.3.9  Over-Temperature Protection (OTP)
      10. 7.3.10 Over-Voltage Protection (OVP)
      11. 7.3.11 Under-Voltage Protection (UVP)
    4. 7.4 Device Functional Modes
      1. 7.4.1 MODE_SEL = LOW: BD Modulation
      2. 7.4.2 MODE_SEL = HIGH: Low-Idle-Current 1SPW Modulation
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Design Requirements
        1. 8.2.1.1 PCB Material Recommendation
        2. 8.2.1.2 PVCC Capacitor Recommendation
        3. 8.2.1.3 Decoupling Capacitor Recommendations
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Ferrite Bead Filter Considerations
        2. 8.2.2.2 Efficiency: LC Filter Required with the Traditional Class-D Modulation Scheme
        3. 8.2.2.3 When to Use an Output Filter for EMI Suppression
        4. 8.2.2.4 Input Resistance
        5. 8.2.2.5 Input Capacitor, Ci
        6. 8.2.2.6 BSN and BSP Capacitors
        7. 8.2.2.7 Differential Inputs
        8. 8.2.2.8 Using Low-ESR Capacitors
      3. 8.2.3 Application Performance Curves
        1. 8.2.3.1 EN55013 Radiated Emissions Results
        2. 8.2.3.2 EN55022 Conducted Emissions Results
  9. 9 Power Supply Recommendations
    1. 9.1 Power Supply Decoupling, CS
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 Support Resources
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)
MINMAXUNIT
Supply voltageAVCC to GND, PVCC to GND–0.320V
Input currentTo any pin except supply pins10mA
Slew rate, maximum(2)SD/ FAULT to GND, GAIN_SEL, MODE_SEL, MUTE10V/ms
Interface pin voltageSD/ FAULT to GND, GAIN_SEL, MODE_SEL, MUTE–0.3AVCC + 0.3V
PLIMIT-0.3GVDD + 0.3V
RINN, RINP, LINN, LINP–0.35.5V
Minimum load resistance, RLBTL, (10 V ≤ PVCC ≤ 14.4 V)4.8Ω
BTL, (3.5 V < PVCC < 10 V)3.2
PBTL, (10 V ≤ PVCC < 14.4 V)2.4
PBTL, (3.5 V ≤ PVCC < 10 V)1.6
Continuous total power dissipationSee the Thermal Information Table
Operating Juncation Temperature range–25150°C
Storage temperature range, Tstg–40125°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The voltage slew rate of these pins must be restricted to no more than 10 V/ms. For higher slew rates, use a 100 kΩ resister in series with the pins.