SLIS117C August   2007  – May 2022 TPIC1021A-Q1

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Typical Characteristics
  9. 9 Parameter Measurement Information
    1. 9.1 Test Circuit
  10. 10Detailed Description
    1. 10.1 Overview
    2. 10.2 Functional Block Diagram
    3. 10.3 Feature Description
      1. 10.3.1 Local Interconnect Network (LIN) Bus
        1. 10.3.1.1 Transmitter Characteristics
        2. 10.3.1.2 Receiver Characteristics
      2. 10.3.2 Transmit Input (TXD)
        1. 10.3.2.1 TXD Dominant State Time-Out
      3. 10.3.3 Receive Output (RXD)
        1. 10.3.3.1 RXD Wake-up Request
      4. 10.3.4 Supply Voltage (VSUP)
      5. 10.3.5 Ground (GND)
      6. 10.3.6 Enable Input (EN)
      7. 10.3.7 NWake Input (NWake)
      8. 10.3.8 Inhibit Output (INH)
    4. 10.4 Device Functional Modes
      1. 10.4.1 Operating States
        1. 10.4.1.1 Normal Mode
        2. 10.4.1.2 Sleep Mode
          1. 10.4.1.2.1 Wake-Up Events
        3. 10.4.1.3 Standby Mode
  11. 11Application and Implementation
    1. 11.1 Application Information
    2. 11.2 Typical Application
      1. 11.2.1 Design Requirements
      2. 11.2.2 Detailed Design Procedure
      3. 11.2.3 Application Curves
    3. 11.3 Power Supply Recommendations
    4. 11.4 Layout
      1. 11.4.1 Layout Guidelines
      2. 11.4.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Receiving Notification of Documentation Updates
    2. 12.2 Support Resources
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

3 Description

The TPIC1021A is the Local Interconnect Network (LIN) physical interface, which integrates the serial transceiver with wake-up and protection features. The LIN bus is a single-wire bidirectional bus typically used for low-speed, in-vehicle networks using data rates between 2.4 kbps and 20 kbps. The LIN protocol output data stream on TXD is converted by the TPIC1021A into the LIN bus signal through a current-limited, wave-shaping driver as outlined by the LIN Physical Layer Specification Revision 2.0. The receiver converts the data stream from the LIN bus and outputs the data stream through RXD. The LIN bus has two states: dominant state (voltage near ground) and the recessive state (voltage near battery). In the recessive state, the LIN bus is pulled high by the TPIC1021A’s internal pullup resistor
(30 kΩ) and series diode, so no external pullup components are required for responder applications. Commander applications require an external pullup resistor (1 kΩ) plus a series diode per the LIN specification.

Device Information
PART NUMBERPACKAGE(1)BODY SIZE (NOM)
TPIC1021A-Q1SOIC (8)4.90 mm × 3.91 mm
(1) For all available packages, see the orderable addendum at the end of the data sheet.
GUID-837D5F85-CD83-4721-B26F-F736A41DA681-low.gifFunctional Block Diagram