SLVSET9F September   2018  – February 2023 TPS1663

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  8. 8 Parameter Measurement Information
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Hot Plug-In and In-Rush Current Control
        1. 9.3.1.1 Thermal Regulation Loop
      2. 9.3.2  Undervoltage Lockout (UVLO)
      3. 9.3.3  Overvoltage Protection (OVP)
      4. 9.3.4  Overload and Short Circuit Protection
        1. 9.3.4.1 Overload Protection
        2. 9.3.4.2 Short Circuit Protection
          1. 9.3.4.2.1 Start-Up With Short-Circuit On Output
      5. 9.3.5  Output Power Limiting, PLIM (TPS16632 Only)
      6. 9.3.6  Current Monitoring Output (IMON)
      7. 9.3.7  FAULT Response (FLT)
      8. 9.3.8  Power Good Output (PGOOD)
      9. 9.3.9  IN, P_IN, OUT and GND Pins
      10. 9.3.10 Thermal Shutdown
      11. 9.3.11 Low Current Shutdown Control (SHDN)
    4. 9.4 Device Functional Modes
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Programming the Current-Limit Threshold R(ILIM) Selection
        2. 10.2.2.2 Undervoltage Lockout and Overvoltage Set Point
        3. 10.2.2.3 Setting Output Voltage Ramp Time (tdVdT)
          1. 10.2.2.3.1 Support Component Selections RPGOOD and C(IN)
      3. 10.2.3 Application Curves
    3. 10.3 System Examples
      1. 10.3.1 Simple 24-V Power Supply Path Protection
    4. 10.4 Power Supply Recommendations
      1. 10.4.1 Transient Protection
    5. 10.5 Layout
      1. 10.5.1 Layout Guidelines
      2. 10.5.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • RGE|24
  • PWP|20
Thermal pad, mechanical data (Package|Pins)
Orderable Information

4 Revision History

Changes from Revision E (March 2020) to Revision F (February 2023)

  • Updated the numbering format for tables, figures and cross-references throughout the documentGo
  • Added Functional Safety-Capable bullet to the Section 1 sectionGo

Changes from Revision D (August 2019) to Revision E (March 2020)

  • Changed UL 2367 and UL 60950 recognition pending to UL 2367 Recognized Go
  • Added IEC 62368-1 Certified to the Section 1 sectionGo

Changes from Revision C (March 2019) to Revision D (August 2019)

  • Changed the absolute maximum voltage in Section 1 Go
  • Changed the adjustable output power limiting in Section 1 Go
  • Changed the Section 7.1 IN, P_IN, OUT, UVLO, FLT, PGOOD maximum input voltageGo
  • Added TA = 25℃ to the Section 7.1 IN, P_IN (10ms transient) input voltageGo
  • Changed the V(OVPF) maximum in Section 7.5 Go
  • Changed V(SEL_PLIM), I(PLIM), and I(dVdT) minimum and maximumGo
  • Changed the P(PLIM) minimum, typical, and maximumGo

Changes from Revision B (December 2018) to Revision C (March 2019)

  • Changed from Advance Information to Production Data Go

Changes from Revision A (October 2018) to Revision B (December 2018)

Changes from Revision * (September 2018) to Revision A (October 2018)

  • Changed Package InformationGo