SLVSF02E march   2019  – may 2023 TPS23881

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
    1. 6.1 Detailed Pin Description
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  9. 8 Parameter Measurement Information
    1. 8.1 Timing Diagrams
  10. 9 Detailed Description
    1. 9.1 Overview
      1. 9.1.1 Operating Modes
        1. 9.1.1.1 Auto
        2. 9.1.1.2 Semiauto
        3. 9.1.1.3 Manual and Diagnostic
        4. 9.1.1.4 Power Off
      2. 9.1.2 PoE Compliance Terminology
      3. 9.1.3 Channel versus Port Terminology
      4. 9.1.4 Requested Class versus Assigned Class
      5. 9.1.5 Power Allocation and Power Demotion
      6. 9.1.6 Programmable SRAM
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Port Remapping
      2. 9.3.2 Port Power Priority
      3. 9.3.3 Analog-to-Digital Converters (ADC)
      4. 9.3.4 I2C Watchdog
      5. 9.3.5 Current Foldback Protection
    4. 9.4 Device Functional Modes
      1. 9.4.1 Detection
      2. 9.4.2 Connection Check
      3. 9.4.3 Classification
      4. 9.4.4 DC Disconnect
    5. 9.5 I2C Programming
      1. 9.5.1 I2C Serial Interface
    6. 9.6 Register Maps
      1. 9.6.1 Complete Register Set
      2. 9.6.2 Detailed Register Descriptions
        1. 9.6.2.1  INTERRUPT Register
        2. 9.6.2.2  INTERRUPT MASK Register
        3. 9.6.2.3  POWER EVENT Register
        4. 9.6.2.4  DETECTION EVENT Register
        5. 9.6.2.5  FAULT EVENT Register
        6. 9.6.2.6  START/ILIM EVENT Register
        7. 9.6.2.7  SUPPLY and FAULT EVENT Register
          1. 9.6.2.7.1 Detected SRAM Faults and "Safe Mode"
            1. 9.6.2.7.1.1 ULA (Ultra Low Alpha) Package Option: TPS23881A
        8. 9.6.2.8  CHANNEL 1 DISCOVERY Register
        9. 9.6.2.9  CHANNEL 2 DISCOVERY Register
        10. 9.6.2.10 CHANNEL 3 DISCOVERY Register
        11. 9.6.2.11 CHANNEL 4 DISCOVERY Register
        12. 9.6.2.12 POWER STATUS Register
        13. 9.6.2.13 PIN STATUS Register
        14. 9.6.2.14 OPERATING MODE Register
        15. 9.6.2.15 DISCONNECT ENABLE Register
        16. 9.6.2.16 DETECT/CLASS ENABLE Register
        17. 9.6.2.17 Power Priority / 2Pair PCUT Disable Register Name
        18. 9.6.2.18 TIMING CONFIGURATION Register
        19. 9.6.2.19 GENERAL MASK Register
        20. 9.6.2.20 DETECT/CLASS RESTART Register
        21. 9.6.2.21 POWER ENABLE Register
        22. 9.6.2.22 RESET Register
        23. 9.6.2.23 ID Register
        24. 9.6.2.24 Connection Check and Auto Class Status Register
        25. 9.6.2.25 2-Pair Police Ch-1 Configuration Register
        26. 9.6.2.26 2-Pair Police Ch-2 Configuration Register
        27. 9.6.2.27 2-Pair Police Ch-3 Configuration Register
        28. 9.6.2.28 2-Pair Police Ch-4 Configuration Register
        29. 9.6.2.29 Capacitance (Legacy PD) Detection
        30. 9.6.2.30 Power-on Fault Register
        31. 9.6.2.31 PORT RE-MAPPING Register
        32. 9.6.2.32 Channels 1 and 2 Multi Bit Priority Register
        33. 9.6.2.33 Channels 3 and 4 Multi Bit Priority Register
        34. 9.6.2.34 4-Pair Wired and Port Power Allocation Register
        35. 9.6.2.35 4-Pair Police Ch-1 and 2 Configuration Register
        36. 9.6.2.36 4-Pair Police Ch-3 and 4 Configuration Register
        37. 9.6.2.37 TEMPERATURE Register
        38. 9.6.2.38 4-Pair Fault Configuration Register
        39. 9.6.2.39 INPUT VOLTAGE Register
        40. 9.6.2.40 CHANNEL 1 CURRENT Register
        41. 9.6.2.41 CHANNEL 2 CURRENT Register
        42. 9.6.2.42 CHANNEL 3 CURRENT Register
        43. 9.6.2.43 CHANNEL 4 CURRENT Register
        44. 9.6.2.44 CHANNEL 1 VOLTAGE Register
        45. 9.6.2.45 CHANNEL 2 VOLTAGE Register
        46. 9.6.2.46 CHANNEL 3 VOLTAGE Register
        47. 9.6.2.47 CHANNEL 4 VOLTAGE Register
        48. 9.6.2.48 2x FOLDBACK SELECTION Register
        49. 9.6.2.49 FIRMWARE REVISION Register
        50. 9.6.2.50 I2C WATCHDOG Register
        51. 9.6.2.51 DEVICE ID Register
        52. 9.6.2.52 CHANNEL 1 DETECT RESISTANCE Register
        53. 9.6.2.53 CHANNEL 2 DETECT RESISTANCE Register
        54. 9.6.2.54 CHANNEL 3 DETECT RESISTANCE Register
        55. 9.6.2.55 CHANNEL 4 DETECT RESISTANCE Register
        56. 9.6.2.56 CHANNEL 1 DETECT CAPACITANCE Register
        57. 9.6.2.57 CHANNEL 2 DETECT CAPACITANCE Register
        58. 9.6.2.58 CHANNEL 3 DETECT CAPACITANCE Register
        59. 9.6.2.59 CHANNEL 4 DETECT CAPACITANCE Register
        60. 9.6.2.60 CHANNEL 1 ASSIGNED CLASS Register
        61. 9.6.2.61 CHANNEL 2 ASSIGNED CLASS Register
        62. 9.6.2.62 CHANNEL 3 ASSIGNED CLASS Register
        63. 9.6.2.63 CHANNEL 4 ASSIGNED CLASS Register
        64. 9.6.2.64 AUTO CLASS CONTROL Register
        65. 9.6.2.65 CHANNEL 1 AUTO CLASS POWER Register
        66. 9.6.2.66 CHANNEL 2 AUTO CLASS POWER Register
        67. 9.6.2.67 CHANNEL 3 AUTO CLASS POWER Register
        68. 9.6.2.68 CHANNEL 4 AUTO CLASS POWER Register
        69. 9.6.2.69 ALTERNATIVE FOLDBACK Register
        70. 9.6.2.70 SRAM CONTROL Register
          1. 9.6.2.70.1 SRAM START ADDRESS (LSB) Register
          2. 9.6.2.70.2 SRAM START ADDRESS (MSB) Register
  11. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Introduction to PoE
        1. 10.1.1.1 2-Pair Versus 4-Pair Power and the New IEEE802.3bt Standard
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Connections on Unused Channels
        2. 10.2.2.2 Power Pin Bypass Capacitors
        3. 10.2.2.3 Per Port Components
        4. 10.2.2.4 System Level Components (not Shown in the Schematic Diagrams)
      3. 10.2.3 Application Curves
  12. 11Power Supply Recommendations
    1. 11.1 VDD
    2. 11.2 VPWR
  13. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Kelvin Current Sensing Resistors
    2. 12.2 Layout Example
      1. 12.2.1 Component Placement and Routing Guidelines
        1. 12.2.1.1 Power Pin Bypass Capacitors
        2. 12.2.1.2 Per-Port Components
  14. 13Device and Documentation Support
    1. 13.1 Documentation Support
      1. 13.1.1 Related Documentation
    2. 13.2 Receiving Notification of Documentation Updates
    3. 13.3 Support Resources
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 Glossary
  15. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

10.2.2.4 System Level Components (not Shown in the Schematic Diagrams)

The system TVS and bulk VPWR capacitance work together to protect the PSE system from surge events which can cause VPWR to surge above 70 V. The TVS and bulk capacitors must be placed on the PCB such that all TPS23881 ports are adequately protected.

  • TVS: The system TVS must be rated for the expected peak surge power of the system and have a minimum reverse standoff voltage of 58 V. Together with the VPWR bulk capacitance, the TVS must prevent the VPWR rail from exceeding 70 V.
  • Bulk Capacitor: The system bulk capacitors must be rated for 100 V and can be of aluminum electrolytic type. Two 47-μF capacitors can be used for each TPS23881 on board.
  • Distributed Capacitance:In higher port count systems, it may be necessary to distribute 1-uF, 100-V, X7R ceramic capacitors across the 54-V power bus. TI recommends one capacitor per each TPS23881 pair.
  • Digital I/O Pullup Resistors:RESET and A1-A4 are internally pulled up to VDD, while OSS is internally pulled down, each with a 50-kΩ (typical) resistor. A stronger pullup and down resistor can be added externally such as a 10 kΩ, 1%, 0.063 W type in a SMT package. SCL, SDAI, SDAO, and INT require external pullup resistors within a range of 1 kΩ to 10 kΩ depending on the total number of devices on the bus.
  • Ethernet Data Transformer (Per Port): The Ethernet data transformer must be rated to operate within the IEEE802.3bt standard in the presence of the DC port current conditions. The transformer is also chosen to be compatible with the Ethernet PHY. The transformer may also be integrated into the RJ45 connector and cable terminations.
  • RJ45 Connector (Per Port): The majority of the RJ45 connector requirements are mechanical in nature and include tab orientation, housing type (shielded or unshielded), or highly integrated. An integrated RJ45 consists of the Ethernet data transformer and cable terminations at a minimum. The integrated type may also contain the port TVS and common mode EMI filtering.
  • Cable Terminations (Per Port): The cable terminations typically consist of series resistor (usually 75 Ω) and capacitor (usually 10 nF) circuits from each data transformer center tap to a common node which is then bypassed to a chassis ground (or system earth ground) with a high-voltage capacitor (usually 1000 pF to 4700 pF at 2 kV).