SLVSF02E march   2019  – may 2023 TPS23881

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
    1. 6.1 Detailed Pin Description
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  9. 8 Parameter Measurement Information
    1. 8.1 Timing Diagrams
  10. 9 Detailed Description
    1. 9.1 Overview
      1. 9.1.1 Operating Modes
        1. 9.1.1.1 Auto
        2. 9.1.1.2 Semiauto
        3. 9.1.1.3 Manual and Diagnostic
        4. 9.1.1.4 Power Off
      2. 9.1.2 PoE Compliance Terminology
      3. 9.1.3 Channel versus Port Terminology
      4. 9.1.4 Requested Class versus Assigned Class
      5. 9.1.5 Power Allocation and Power Demotion
      6. 9.1.6 Programmable SRAM
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Port Remapping
      2. 9.3.2 Port Power Priority
      3. 9.3.3 Analog-to-Digital Converters (ADC)
      4. 9.3.4 I2C Watchdog
      5. 9.3.5 Current Foldback Protection
    4. 9.4 Device Functional Modes
      1. 9.4.1 Detection
      2. 9.4.2 Connection Check
      3. 9.4.3 Classification
      4. 9.4.4 DC Disconnect
    5. 9.5 I2C Programming
      1. 9.5.1 I2C Serial Interface
    6. 9.6 Register Maps
      1. 9.6.1 Complete Register Set
      2. 9.6.2 Detailed Register Descriptions
        1. 9.6.2.1  INTERRUPT Register
        2. 9.6.2.2  INTERRUPT MASK Register
        3. 9.6.2.3  POWER EVENT Register
        4. 9.6.2.4  DETECTION EVENT Register
        5. 9.6.2.5  FAULT EVENT Register
        6. 9.6.2.6  START/ILIM EVENT Register
        7. 9.6.2.7  SUPPLY and FAULT EVENT Register
          1. 9.6.2.7.1 Detected SRAM Faults and "Safe Mode"
            1. 9.6.2.7.1.1 ULA (Ultra Low Alpha) Package Option: TPS23881A
        8. 9.6.2.8  CHANNEL 1 DISCOVERY Register
        9. 9.6.2.9  CHANNEL 2 DISCOVERY Register
        10. 9.6.2.10 CHANNEL 3 DISCOVERY Register
        11. 9.6.2.11 CHANNEL 4 DISCOVERY Register
        12. 9.6.2.12 POWER STATUS Register
        13. 9.6.2.13 PIN STATUS Register
        14. 9.6.2.14 OPERATING MODE Register
        15. 9.6.2.15 DISCONNECT ENABLE Register
        16. 9.6.2.16 DETECT/CLASS ENABLE Register
        17. 9.6.2.17 Power Priority / 2Pair PCUT Disable Register Name
        18. 9.6.2.18 TIMING CONFIGURATION Register
        19. 9.6.2.19 GENERAL MASK Register
        20. 9.6.2.20 DETECT/CLASS RESTART Register
        21. 9.6.2.21 POWER ENABLE Register
        22. 9.6.2.22 RESET Register
        23. 9.6.2.23 ID Register
        24. 9.6.2.24 Connection Check and Auto Class Status Register
        25. 9.6.2.25 2-Pair Police Ch-1 Configuration Register
        26. 9.6.2.26 2-Pair Police Ch-2 Configuration Register
        27. 9.6.2.27 2-Pair Police Ch-3 Configuration Register
        28. 9.6.2.28 2-Pair Police Ch-4 Configuration Register
        29. 9.6.2.29 Capacitance (Legacy PD) Detection
        30. 9.6.2.30 Power-on Fault Register
        31. 9.6.2.31 PORT RE-MAPPING Register
        32. 9.6.2.32 Channels 1 and 2 Multi Bit Priority Register
        33. 9.6.2.33 Channels 3 and 4 Multi Bit Priority Register
        34. 9.6.2.34 4-Pair Wired and Port Power Allocation Register
        35. 9.6.2.35 4-Pair Police Ch-1 and 2 Configuration Register
        36. 9.6.2.36 4-Pair Police Ch-3 and 4 Configuration Register
        37. 9.6.2.37 TEMPERATURE Register
        38. 9.6.2.38 4-Pair Fault Configuration Register
        39. 9.6.2.39 INPUT VOLTAGE Register
        40. 9.6.2.40 CHANNEL 1 CURRENT Register
        41. 9.6.2.41 CHANNEL 2 CURRENT Register
        42. 9.6.2.42 CHANNEL 3 CURRENT Register
        43. 9.6.2.43 CHANNEL 4 CURRENT Register
        44. 9.6.2.44 CHANNEL 1 VOLTAGE Register
        45. 9.6.2.45 CHANNEL 2 VOLTAGE Register
        46. 9.6.2.46 CHANNEL 3 VOLTAGE Register
        47. 9.6.2.47 CHANNEL 4 VOLTAGE Register
        48. 9.6.2.48 2x FOLDBACK SELECTION Register
        49. 9.6.2.49 FIRMWARE REVISION Register
        50. 9.6.2.50 I2C WATCHDOG Register
        51. 9.6.2.51 DEVICE ID Register
        52. 9.6.2.52 CHANNEL 1 DETECT RESISTANCE Register
        53. 9.6.2.53 CHANNEL 2 DETECT RESISTANCE Register
        54. 9.6.2.54 CHANNEL 3 DETECT RESISTANCE Register
        55. 9.6.2.55 CHANNEL 4 DETECT RESISTANCE Register
        56. 9.6.2.56 CHANNEL 1 DETECT CAPACITANCE Register
        57. 9.6.2.57 CHANNEL 2 DETECT CAPACITANCE Register
        58. 9.6.2.58 CHANNEL 3 DETECT CAPACITANCE Register
        59. 9.6.2.59 CHANNEL 4 DETECT CAPACITANCE Register
        60. 9.6.2.60 CHANNEL 1 ASSIGNED CLASS Register
        61. 9.6.2.61 CHANNEL 2 ASSIGNED CLASS Register
        62. 9.6.2.62 CHANNEL 3 ASSIGNED CLASS Register
        63. 9.6.2.63 CHANNEL 4 ASSIGNED CLASS Register
        64. 9.6.2.64 AUTO CLASS CONTROL Register
        65. 9.6.2.65 CHANNEL 1 AUTO CLASS POWER Register
        66. 9.6.2.66 CHANNEL 2 AUTO CLASS POWER Register
        67. 9.6.2.67 CHANNEL 3 AUTO CLASS POWER Register
        68. 9.6.2.68 CHANNEL 4 AUTO CLASS POWER Register
        69. 9.6.2.69 ALTERNATIVE FOLDBACK Register
        70. 9.6.2.70 SRAM CONTROL Register
          1. 9.6.2.70.1 SRAM START ADDRESS (LSB) Register
          2. 9.6.2.70.2 SRAM START ADDRESS (MSB) Register
  11. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Introduction to PoE
        1. 10.1.1.1 2-Pair Versus 4-Pair Power and the New IEEE802.3bt Standard
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Connections on Unused Channels
        2. 10.2.2.2 Power Pin Bypass Capacitors
        3. 10.2.2.3 Per Port Components
        4. 10.2.2.4 System Level Components (not Shown in the Schematic Diagrams)
      3. 10.2.3 Application Curves
  12. 11Power Supply Recommendations
    1. 11.1 VDD
    2. 11.2 VPWR
  13. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Kelvin Current Sensing Resistors
    2. 12.2 Layout Example
      1. 12.2.1 Component Placement and Routing Guidelines
        1. 12.2.1.1 Power Pin Bypass Capacitors
        2. 12.2.1.2 Per-Port Components
  14. 13Device and Documentation Support
    1. 13.1 Documentation Support
      1. 13.1.1 Related Documentation
    2. 13.2 Receiving Notification of Documentation Updates
    3. 13.3 Support Resources
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 Glossary
  15. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.6.2.16 DETECT/CLASS ENABLE Register

COMMAND = 14h with 1 Data Byte, Read/Write

During tOVLD, tLIM or tSTART cool down cycle, any Detect/Class Enable command for that channel will be delayed until end of cool-down period. Note that at the end of cool down cycle, one or more detection/class cycles are automatically restarted as described previously, if the class and/or detect enable bits are set.

Figure 9-23 DETECT/CLASS ENABLE Register Format
76543210
CLE4CLE3CLE2CLE1DETE4DETE3DETE2DETE1
R/W-0R/W-0R/W-0R/W-0R/W-0R/W-0R/W-0R/W-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 9-21 DETECT/CLASS ENABLE Register Field Descriptions
BitFieldTypeResetDescription
7–4CLE4-CLE1R/W0Classification enable bits.
3–0DETE4-DETE1R/W0Detection enable bits.

Bit Descriptions:

Detection and classification enable for each channel.

When in Manual mode, setting a bit means that only one cycle (detection or classification) is performed for the corresponding channel. The bit is automatically cleared by the time the cycle has been completed.

Note that similar result can be obtained by writing to the Detect/Class Restart register 0x18.

It is also cleared if a turn off (Power Enable register) command is issued.

When in semiauto mode, as long as the port is kept off, detection and classification are performed continuously, as long as the class and detect enable bits are kept set, but the class will be done only if the detection was valid. A Detect/Class Restart PB command can also be used to set the CLEn and DETEn bits, if in semiauto mode.

Note:

For 4-pair wired Ports in Semi-Auto or Auto mode, both DETEn and CLEn bits need to be set on both channels in order for Detection or Classification to be enabled

Note:

In Manual/Diagnostic mode, it is recommenced that a Port Reset command (see register 0x1A Section 9.6.2.22) be completed prior to enabling discovery (DETEn or CLEn).