The TPS35 offers high accuracy
under voltage supervisor function at very low quiescent current. The voltage
supervisor function is always active. After the device powers up from VDD <
VPOR, the RESET and WDO outputs are actively driven when VDD is
greater than VPOR. The device starts monitoring the supply level when the
VDD voltage is greater than 1.04 V. The device holds the RESET pin asserted for
tSTRT + tD time after the VDD > VIT+
(VIT- + VHYS). Refer
TPS35-Q1 Precision Voltage Supervisor with Programmable Watchdog Timer
TPS35 Nano IQ Precision Voltage Supervisor with Precision Timeout Watchdog Timer
TPS35 Nano IQ Precision Voltage Supervisor with Precision Timeout Watchdog Timer
Features
Features
Applications
Applications
Description
Description
Table of Contents
Table of Contents
Device Comparison
Device Comparison
Pin Configuration and Functions
Pin Configuration and Functions
Specifications
Specifications
Absolute Maximum Ratings
Absolute Maximum Ratings
ESD Ratings
ESD Ratings
Recommended Operating Conditions
Recommended Operating Conditions
Thermal Information
Thermal Information
Thermal Information
Thermal Information
Electrical Characteristics
Electrical Characteristics
Timing Requirements
Timing Requirements
Switching Characteristics
Switching Characteristics
Timing Diagrams
Timing Diagrams
Typical Characteristics
Typical Characteristics
Detailed Description
Detailed Description
Overview
Overview
Functional Block Diagrams
Functional Block Diagrams
Feature Description
Feature Description
Voltage Supervisor
Voltage Supervisor
Timeout Watchdog Timer
Timeout Watchdog Timer
tWD Timer
tWD Timer
Watchdog Enable Disable Operation
Watchdog Enable Disable Operation
tSD Watchdog Start Up Delay
tSD Watchdog Start Up Delay
SET Pin Behavior
SET Pin Behavior
Manual RESET
Manual RESET
RESET and WDO Output
RESET and WDO Output
Device Functional Modes
Device Functional Modes
Application and Implementation
Application and Implementation
Application Information
Application Information
Output Assert Delay
Output Assert Delay
Factory-Programmed Output Assert Delay Timing
Factory-Programmed Output Assert Delay Timing
Adjustable Capacitor Timing
Adjustable Capacitor Timing
Watchdog Timer Functionality
Watchdog Timer Functionality
Factory-Programmed Timing Options
Factory-Programmed Timing Options
Adjustable Capacitor Timing
Adjustable Capacitor Timing
Typical Applications
Typical Applications
Design 1: Monitoring a Microcontroller Supply Voltage and Watchdog Timer
Design 1: Monitoring a Microcontroller Supply Voltage and Watchdog Timer
Design Requirements
Design Requirements
Detailed Design Procedure
Detailed Design Procedure
Setting the Voltage Threshold
Setting the Voltage Threshold
Meeting the Watchdog Timeout Period
Meeting the Watchdog Timeout Period
Setting the Reset Delay
Setting the Reset Delay
Setting the Startup Delay and Output Topology
Setting the Startup Delay and Output Topology
Calculating the RESET Pullup Resistor
Calculating the RESET Pullup Resistor
Power Supply Recommendations
Power Supply Recommendations
Layout
Layout
Layout Guidelines
Layout Guidelines
Layout Example
Layout Example
Device and Documentation Support
Device and Documentation Support
Receiving Notification of Documentation Updates
Receiving Notification of Documentation Updates
Support Resources
Support Resources
Trademarks
Trademarks
Electrostatic Discharge Caution
Electrostatic Discharge Caution
Glossary
Glossary
Revision History
Revision History
Mechanical, Packaging, and Orderable Information
Mechanical, Packaging, and Orderable Information
IMPORTANT NOTICE AND DISCLAIMER
IMPORTANT NOTICE AND DISCLAIMER
TPS35
Nano IQ Precision Voltage Supervisor with Precision Timeout Watchdog Timer
TPS35
Nano IQ Precision Voltage Supervisor with Precision Timeout Watchdog TimerTPS35Precision Voltage Supervisor with Timeout
Features
Factory programmed or user-programmable watchdog
timeout
±10% Accurate timer (maximum)
Factory programmed: 1 msec to 100 sec
Factory programmed or user-programmable reset
delay
±10% Accurate timer (maximum)
Factory programmed option: 2 msec to 10 sec
Input voltage range: VDD = 1.04 V to
6.0 V
Fixed threshold voltage (VIT-): 1.05 V
to 5.4 V
Threshold voltage available in 50 mV steps
1.2% Voltage threshold accuracy (maximum)
Built-in hysteresis (VHYS): 5%
(typical)
Ultra low supply current: IDD = 250 nA
(typical)
Open-drain, push-pull; active-low outputs
Various programmability options:
Watchdog enable-disable
Watchdog startup delay: no delay to 10 sec
On
the fly timer extension: 1X to 256X
Latched output option
MR functionality
support
Features
Factory programmed or user-programmable watchdog
timeout
±10% Accurate timer (maximum)
Factory programmed: 1 msec to 100 sec
Factory programmed or user-programmable reset
delay
±10% Accurate timer (maximum)
Factory programmed option: 2 msec to 10 sec
Input voltage range: VDD = 1.04 V to
6.0 V
Fixed threshold voltage (VIT-): 1.05 V
to 5.4 V
Threshold voltage available in 50 mV steps
1.2% Voltage threshold accuracy (maximum)
Built-in hysteresis (VHYS): 5%
(typical)
Ultra low supply current: IDD = 250 nA
(typical)
Open-drain, push-pull; active-low outputs
Various programmability options:
Watchdog enable-disable
Watchdog startup delay: no delay to 10 sec
On
the fly timer extension: 1X to 256X
Latched output option
MR functionality
support
Factory programmed or user-programmable watchdog
timeout
±10% Accurate timer (maximum)
Factory programmed: 1 msec to 100 sec
Factory programmed or user-programmable reset
delay
±10% Accurate timer (maximum)
Factory programmed option: 2 msec to 10 sec
Input voltage range: VDD = 1.04 V to
6.0 V
Fixed threshold voltage (VIT-): 1.05 V
to 5.4 V
Threshold voltage available in 50 mV steps
1.2% Voltage threshold accuracy (maximum)
Built-in hysteresis (VHYS): 5%
(typical)
Ultra low supply current: IDD = 250 nA
(typical)
Open-drain, push-pull; active-low outputs
Various programmability options:
Watchdog enable-disable
Watchdog startup delay: no delay to 10 sec
On
the fly timer extension: 1X to 256X
Latched output option
MR functionality
support
Factory programmed or user-programmable watchdog
timeout
±10% Accurate timer (maximum)
Factory programmed: 1 msec to 100 sec
Factory programmed or user-programmable reset
delay
±10% Accurate timer (maximum)
Factory programmed option: 2 msec to 10 sec
Input voltage range: VDD = 1.04 V to
6.0 V
Fixed threshold voltage (VIT-): 1.05 V
to 5.4 V
Threshold voltage available in 50 mV steps
1.2% Voltage threshold accuracy (maximum)
Built-in hysteresis (VHYS): 5%
(typical)
Ultra low supply current: IDD = 250 nA
(typical)
Open-drain, push-pull; active-low outputs
Various programmability options:
Watchdog enable-disable
Watchdog startup delay: no delay to 10 sec
On
the fly timer extension: 1X to 256X
Latched output option
MR functionality
support
Factory programmed or user-programmable watchdog
timeout
±10% Accurate timer (maximum)
Factory programmed: 1 msec to 100 sec
±10% Accurate timer (maximum)
Factory programmed: 1 msec to 100 sec
±10% Accurate timer (maximum)Factory programmed: 1 msec to 100 secFactory programmed or user-programmable reset
delay
±10% Accurate timer (maximum)
Factory programmed option: 2 msec to 10 sec
±10% Accurate timer (maximum)
Factory programmed option: 2 msec to 10 sec
±10% Accurate timer (maximum)Factory programmed option: 2 msec to 10 secInput voltage range: VDD = 1.04 V to
6.0 VDDFixed threshold voltage (VIT-): 1.05 V
to 5.4 V
Threshold voltage available in 50 mV steps
1.2% Voltage threshold accuracy (maximum)
Built-in hysteresis (VHYS): 5%
(typical)
IT-
Threshold voltage available in 50 mV steps
1.2% Voltage threshold accuracy (maximum)
Built-in hysteresis (VHYS): 5%
(typical)
Threshold voltage available in 50 mV steps1.2% Voltage threshold accuracy (maximum)Built-in hysteresis (VHYS): 5%
(typical)HYSUltra low supply current: IDD = 250 nA
(typical)DDOpen-drain, push-pull; active-low outputsVarious programmability options:
Watchdog enable-disable
Watchdog startup delay: no delay to 10 sec
On
the fly timer extension: 1X to 256X
Latched output option
Watchdog enable-disable
Watchdog startup delay: no delay to 10 sec
On
the fly timer extension: 1X to 256X
Latched output option
Watchdog enable-disableWatchdog startup delay: no delay to 10 secOn
the fly timer extension: 1X to 256XLatched output option
MR functionality
supportMR
Applications
Robot servo drive
Mixed module (AI, AO, DI,
DO)
HVAC controller
Electricity meter
Infusion pump
Surgical equipment
Applications
Robot servo drive
Mixed module (AI, AO, DI,
DO)
HVAC controller
Electricity meter
Infusion pump
Surgical equipment
Robot servo drive
Mixed module (AI, AO, DI,
DO)
HVAC controller
Electricity meter
Infusion pump
Surgical equipment
Robot servo drive
Mixed module (AI, AO, DI,
DO)
HVAC controller
Electricity meter
Infusion pump
Surgical equipment
Robot servo drive
Robot servo drive
Mixed module (AI, AO, DI,
DO)
Mixed module (AI, AO, DI,
DO)
HVAC controller
HVAC controller
Electricity meter
Electricity meter
Infusion pump
Infusion pump
Surgical equipment
Surgical equipment
Description
A
20231214
Removed PREVIEW status for DSE package
yes
The TPS35 is an ultra-low
power consumption (250 nA typical) device offering a
precision voltage supervisor with a programmable timeout watchdog timer. The TPS35 supports wide threshold levels for undervoltage
supervision with 1.2% accuracy across the specified temperature range.
The TPS35 offers a high accuracy timeout watchdog timer with a host
of features for a wide variety of applications. The timeout watchdog timer can be
factory programmed or user programmed using an external capacitor. The timer value
can be changed on-the-fly using a combination of logic pins. The watchdog also
offers unique features such as enable-disable, start-up delay, independent WDO pin
option.
The
RESET or
WDO delay can be
set by factory-programmed default delay settings or programmed by an external
capacitor. The device also offers a latched
output operation where the output is latched until the supervisor or watchdog fault is cleared.
The TPS35 provides a
performance upgrade alternative to
TPS3851
device family. The TPS35 is available in a small 6-pin WSON and 8-pin SOT-23 package.
Device Information
PART NUMBER
PACKAGE
#GUID-A90FCBEA-9211-41EC-A530-F55740F95637/DEVINFONOTE
BODY SIZE (NOM)
TPS35
DDF (8)
2.90 mm × 1.60 mm
TPS35
DSE (6)
1.50 mm × 1.50 mm
For all available packages, see the orderable addendum at the end of the data sheet.
Typical Application Circuit
Description
A
20231214
Removed PREVIEW status for DSE package
yes
A
20231214
Removed PREVIEW status for DSE package
yes
A
20231214
Removed PREVIEW status for DSE package
yes
A20231214Removed PREVIEW status for DSE packageyes
The TPS35 is an ultra-low
power consumption (250 nA typical) device offering a
precision voltage supervisor with a programmable timeout watchdog timer. The TPS35 supports wide threshold levels for undervoltage
supervision with 1.2% accuracy across the specified temperature range.
The TPS35 offers a high accuracy timeout watchdog timer with a host
of features for a wide variety of applications. The timeout watchdog timer can be
factory programmed or user programmed using an external capacitor. The timer value
can be changed on-the-fly using a combination of logic pins. The watchdog also
offers unique features such as enable-disable, start-up delay, independent WDO pin
option.
The
RESET or
WDO delay can be
set by factory-programmed default delay settings or programmed by an external
capacitor. The device also offers a latched
output operation where the output is latched until the supervisor or watchdog fault is cleared.
The TPS35 provides a
performance upgrade alternative to
TPS3851
device family. The TPS35 is available in a small 6-pin WSON and 8-pin SOT-23 package.
Device Information
PART NUMBER
PACKAGE
#GUID-A90FCBEA-9211-41EC-A530-F55740F95637/DEVINFONOTE
BODY SIZE (NOM)
TPS35
DDF (8)
2.90 mm × 1.60 mm
TPS35
DSE (6)
1.50 mm × 1.50 mm
For all available packages, see the orderable addendum at the end of the data sheet.
Typical Application Circuit
The TPS35 is an ultra-low
power consumption (250 nA typical) device offering a
precision voltage supervisor with a programmable timeout watchdog timer. The TPS35 supports wide threshold levels for undervoltage
supervision with 1.2% accuracy across the specified temperature range.
The TPS35 offers a high accuracy timeout watchdog timer with a host
of features for a wide variety of applications. The timeout watchdog timer can be
factory programmed or user programmed using an external capacitor. The timer value
can be changed on-the-fly using a combination of logic pins. The watchdog also
offers unique features such as enable-disable, start-up delay, independent WDO pin
option.
The
RESET or
WDO delay can be
set by factory-programmed default delay settings or programmed by an external
capacitor. The device also offers a latched
output operation where the output is latched until the supervisor or watchdog fault is cleared.
The TPS35 provides a
performance upgrade alternative to
TPS3851
device family. The TPS35 is available in a small 6-pin WSON and 8-pin SOT-23 package.
Device Information
PART NUMBER
PACKAGE
#GUID-A90FCBEA-9211-41EC-A530-F55740F95637/DEVINFONOTE
BODY SIZE (NOM)
TPS35
DDF (8)
2.90 mm × 1.60 mm
TPS35
DSE (6)
1.50 mm × 1.50 mm
For all available packages, see the orderable addendum at the end of the data sheet.
The TPS35 is an ultra-low
power consumption (250 nA typical) device offering a
precision voltage supervisor with a programmable timeout watchdog timer. The TPS35 supports wide threshold levels for undervoltage
supervision with 1.2% accuracy across the specified temperature range.
TPS35a
precision voltage supervisor with timeout The TPS35 supports wide threshold levels for undervoltage
supervision with 1.2% accuracy across the specified temperature range.TPS35The TPS35 offers a high accuracy timeout watchdog timer with a host
of features for a wide variety of applications. The timeout watchdog timer can be
factory programmed or user programmed using an external capacitor. The timer value
can be changed on-the-fly using a combination of logic pins. The watchdog also
offers unique features such as enable-disable, start-up delay, independent WDO pin
option.TPS35The
RESET or
WDO delay can be
set by factory-programmed default delay settings or programmed by an external
capacitor. The device also offers a latched
output operation where the output is latched until the supervisor or watchdog fault is cleared.
RESET or RESETWDOsupervisor or The TPS35 provides a
performance upgrade alternative to
TPS3851
device family. The TPS35 is available in a small 6-pin WSON and 8-pin SOT-23 package.TPS35
TPS3851
TPS3851TPS356-pin WSON and
Device Information
PART NUMBER
PACKAGE
#GUID-A90FCBEA-9211-41EC-A530-F55740F95637/DEVINFONOTE
BODY SIZE (NOM)
TPS35
DDF (8)
2.90 mm × 1.60 mm
TPS35
DSE (6)
1.50 mm × 1.50 mm
Device Information
PART NUMBER
PACKAGE
#GUID-A90FCBEA-9211-41EC-A530-F55740F95637/DEVINFONOTE
BODY SIZE (NOM)
TPS35
DDF (8)
2.90 mm × 1.60 mm
TPS35
DSE (6)
1.50 mm × 1.50 mm
PART NUMBER
PACKAGE
#GUID-A90FCBEA-9211-41EC-A530-F55740F95637/DEVINFONOTE
BODY SIZE (NOM)
PART NUMBER
PACKAGE
#GUID-A90FCBEA-9211-41EC-A530-F55740F95637/DEVINFONOTE
BODY SIZE (NOM)
PART NUMBERPACKAGE
#GUID-A90FCBEA-9211-41EC-A530-F55740F95637/DEVINFONOTE
#GUID-A90FCBEA-9211-41EC-A530-F55740F95637/DEVINFONOTE
#GUID-A90FCBEA-9211-41EC-A530-F55740F95637/DEVINFONOTEBODY SIZE (NOM)
TPS35
DDF (8)
2.90 mm × 1.60 mm
TPS35
DSE (6)
1.50 mm × 1.50 mm
TPS35
DDF (8)
2.90 mm × 1.60 mm
TPS35
TPS35DDF (8)2.90 mm × 1.60 mm
TPS35
DSE (6)
1.50 mm × 1.50 mm
TPS35
TPS35DSE (6) 1.50 mm × 1.50 mm
For all available packages, see the orderable addendum at the end of the data sheet.
For all available packages, see the orderable addendum at the end of the data sheet.
Typical Application Circuit
Typical Application Circuit
Typical Application Circuit
Typical Application Circuit
Table of Contents
yes
Table of Contents
yes
yes
yes
Device Comparison
shows the device naming nomenclature of the TPS35. For all possible output types, threshold voltage options, watchdog time options and output assert delay options, see for more details. Contact TI sales representatives or on TI's E2E forum for detail and availability of other options.
Device Naming
Nomenclature
TPS35 belongs to family of pin compatible devices offering different feature sets as highlighted in .
Pin Compatible Device Families
DEVICE
VOLTAGE SUPERVISOR
TYPE OF WATCHDOG
TPS35
Yes
Timeout
TPS36
Yes
Window
TPS3435
No
Timeout
TPS3436
No
Window
Device Comparison
shows the device naming nomenclature of the TPS35. For all possible output types, threshold voltage options, watchdog time options and output assert delay options, see for more details. Contact TI sales representatives or on TI's E2E forum for detail and availability of other options.
Device Naming
Nomenclature
TPS35 belongs to family of pin compatible devices offering different feature sets as highlighted in .
Pin Compatible Device Families
DEVICE
VOLTAGE SUPERVISOR
TYPE OF WATCHDOG
TPS35
Yes
Timeout
TPS36
Yes
Window
TPS3435
No
Timeout
TPS3436
No
Window
shows the device naming nomenclature of the TPS35. For all possible output types, threshold voltage options, watchdog time options and output assert delay options, see for more details. Contact TI sales representatives or on TI's E2E forum for detail and availability of other options.
Device Naming
Nomenclature
TPS35 belongs to family of pin compatible devices offering different feature sets as highlighted in .
Pin Compatible Device Families
DEVICE
VOLTAGE SUPERVISOR
TYPE OF WATCHDOG
TPS35
Yes
Timeout
TPS36
Yes
Window
TPS3435
No
Timeout
TPS3436
No
Window
shows the device naming nomenclature of the TPS35. For all possible output types, threshold voltage options, watchdog time options and output assert delay options, see for more details. Contact TI sales representatives or on TI's E2E forum for detail and availability of other options.TPS35threshold voltage options, E2E forum
Device Naming
Nomenclature
Device Naming
Nomenclature
TPS35 belongs to family of pin compatible devices offering different feature sets as highlighted in .TPS35
Pin Compatible Device Families
DEVICE
VOLTAGE SUPERVISOR
TYPE OF WATCHDOG
TPS35
Yes
Timeout
TPS36
Yes
Window
TPS3435
No
Timeout
TPS3436
No
Window
Pin Compatible Device Families
DEVICE
VOLTAGE SUPERVISOR
TYPE OF WATCHDOG
TPS35
Yes
Timeout
TPS36
Yes
Window
TPS3435
No
Timeout
TPS3436
No
Window
DEVICE
VOLTAGE SUPERVISOR
TYPE OF WATCHDOG
DEVICE
VOLTAGE SUPERVISOR
TYPE OF WATCHDOG
DEVICEVOLTAGE SUPERVISORTYPE OF WATCHDOG
TPS35
Yes
Timeout
TPS36
Yes
Window
TPS3435
No
Timeout
TPS3436
No
Window
TPS35
Yes
Timeout
TPS35
TPS35
TPS35YesTimeout
TPS36
Yes
Window
TPS36
TPS36
TPS36YesWindow
TPS3435
No
Timeout
TPS3435
TPS3435
TPS3435NoTimeout
TPS3436
No
Window
TPS3436
TPS3436
TPS3436NoWindow
Pin Configuration and Functions
Pin Configuration Option
A
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
B
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
C
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
D
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
J
DSE Package,
6-Pin WSON,
TPS35 Top View
Pin Configuration Option
K
DSE Package,
6-Pin WSON,
TPS35 Top View
Pin Functions
PIN NAME
PIN NUMBER
I/O
DESCRIPTION
PINOUT A
PINOUT B
PINOUT C
PINOUT D
PINOUT J
PINOUT K
CRST
3
3
—
—
—
2
I
Programmable reset timeout pin.
Connect a capacitor between this pin and GND to program the reset
timeout period. See
for
more details.
CWD
2
2
—
—
—
1
I
Programmable watchdog timeout input. Watchdog timeout is set by
connecting a capacitor between this pin and ground. See
for
more details.
GND
4
4
4
4
4
4
—
Ground
pin
MR
1
—
2
—
—
—
I
Manual reset
pin. A logic low on this pin asserts the RESET.
See
for
more details.
RESET
7
7
7
7
5
5
O
Reset output. Connect
RESET to VDD using a pull up resistance
when using open drain output. RESET is asserted
when the voltage at the VDD pin goes below the undervoltage
threshold (VIT-) or MR pin is driven
LOW. For pinout options which do not support independent
WDO pin, RESET is also
asserted for watchdog error. See
for
more details.
SET0
5
1
1
1
1
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
SET1
—
5
5
5
—
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
VDD
8
8
8
8
6
6
I
Supply voltage
pin. For noisy systems, connecting a 0.1-µF bypass capacitor is
recommended.
WD-EN
—
—
6
2
2
—
I
Logic input.
Logic high input enables the watchdog monitoring feature. See
for
more details.
WDI
6
6
3
3
3
3
I
Watchdog input.
A falling transition (edge) must occur at this pin before the timeout expires in
order for RESET / WDO to
not assert. See
for
more details.
WDO
—
—
—
6
—
—
O
Watchdog
output. Connect WDO to VDD using pull up
resistance when using open drain output. WDO
asserts when a watchdog error occurs. WDO only
asserts when RESET is high. When a watchdog
error occurs, WDO asserts for the set
RESET timeout delay (tD). When
RESET is asserted, WDO
is deasserted and watchdog functionality is disabled. See
for
more details.
Pin Configuration and Functions
Pin Configuration Option
A
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
B
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
C
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
D
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
J
DSE Package,
6-Pin WSON,
TPS35 Top View
Pin Configuration Option
K
DSE Package,
6-Pin WSON,
TPS35 Top View
Pin Functions
PIN NAME
PIN NUMBER
I/O
DESCRIPTION
PINOUT A
PINOUT B
PINOUT C
PINOUT D
PINOUT J
PINOUT K
CRST
3
3
—
—
—
2
I
Programmable reset timeout pin.
Connect a capacitor between this pin and GND to program the reset
timeout period. See
for
more details.
CWD
2
2
—
—
—
1
I
Programmable watchdog timeout input. Watchdog timeout is set by
connecting a capacitor between this pin and ground. See
for
more details.
GND
4
4
4
4
4
4
—
Ground
pin
MR
1
—
2
—
—
—
I
Manual reset
pin. A logic low on this pin asserts the RESET.
See
for
more details.
RESET
7
7
7
7
5
5
O
Reset output. Connect
RESET to VDD using a pull up resistance
when using open drain output. RESET is asserted
when the voltage at the VDD pin goes below the undervoltage
threshold (VIT-) or MR pin is driven
LOW. For pinout options which do not support independent
WDO pin, RESET is also
asserted for watchdog error. See
for
more details.
SET0
5
1
1
1
1
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
SET1
—
5
5
5
—
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
VDD
8
8
8
8
6
6
I
Supply voltage
pin. For noisy systems, connecting a 0.1-µF bypass capacitor is
recommended.
WD-EN
—
—
6
2
2
—
I
Logic input.
Logic high input enables the watchdog monitoring feature. See
for
more details.
WDI
6
6
3
3
3
3
I
Watchdog input.
A falling transition (edge) must occur at this pin before the timeout expires in
order for RESET / WDO to
not assert. See
for
more details.
WDO
—
—
—
6
—
—
O
Watchdog
output. Connect WDO to VDD using pull up
resistance when using open drain output. WDO
asserts when a watchdog error occurs. WDO only
asserts when RESET is high. When a watchdog
error occurs, WDO asserts for the set
RESET timeout delay (tD). When
RESET is asserted, WDO
is deasserted and watchdog functionality is disabled. See
for
more details.
Pin Configuration Option
A
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
B
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
C
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
D
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
J
DSE Package,
6-Pin WSON,
TPS35 Top View
Pin Configuration Option
K
DSE Package,
6-Pin WSON,
TPS35 Top View
Pin Functions
PIN NAME
PIN NUMBER
I/O
DESCRIPTION
PINOUT A
PINOUT B
PINOUT C
PINOUT D
PINOUT J
PINOUT K
CRST
3
3
—
—
—
2
I
Programmable reset timeout pin.
Connect a capacitor between this pin and GND to program the reset
timeout period. See
for
more details.
CWD
2
2
—
—
—
1
I
Programmable watchdog timeout input. Watchdog timeout is set by
connecting a capacitor between this pin and ground. See
for
more details.
GND
4
4
4
4
4
4
—
Ground
pin
MR
1
—
2
—
—
—
I
Manual reset
pin. A logic low on this pin asserts the RESET.
See
for
more details.
RESET
7
7
7
7
5
5
O
Reset output. Connect
RESET to VDD using a pull up resistance
when using open drain output. RESET is asserted
when the voltage at the VDD pin goes below the undervoltage
threshold (VIT-) or MR pin is driven
LOW. For pinout options which do not support independent
WDO pin, RESET is also
asserted for watchdog error. See
for
more details.
SET0
5
1
1
1
1
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
SET1
—
5
5
5
—
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
VDD
8
8
8
8
6
6
I
Supply voltage
pin. For noisy systems, connecting a 0.1-µF bypass capacitor is
recommended.
WD-EN
—
—
6
2
2
—
I
Logic input.
Logic high input enables the watchdog monitoring feature. See
for
more details.
WDI
6
6
3
3
3
3
I
Watchdog input.
A falling transition (edge) must occur at this pin before the timeout expires in
order for RESET / WDO to
not assert. See
for
more details.
WDO
—
—
—
6
—
—
O
Watchdog
output. Connect WDO to VDD using pull up
resistance when using open drain output. WDO
asserts when a watchdog error occurs. WDO only
asserts when RESET is high. When a watchdog
error occurs, WDO asserts for the set
RESET timeout delay (tD). When
RESET is asserted, WDO
is deasserted and watchdog functionality is disabled. See
for
more details.
Pin Configuration Option
A
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
B
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
C
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
D
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
J
DSE Package,
6-Pin WSON,
TPS35 Top View
Pin Configuration Option
K
DSE Package,
6-Pin WSON,
TPS35 Top View
Pin Configuration Option
A
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
A
DDF Package,
8-Pin SOT-23,
TPS35 Top View
DDF Package,
8-Pin SOT-23,
TPS35 Top ViewTPS35
Pin Configuration Option
B
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
B
DDF Package,
8-Pin SOT-23,
TPS35 Top View
DDF Package,
8-Pin SOT-23,
TPS35 Top ViewTPS35
Pin Configuration Option
C
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
C
DDF Package,
8-Pin SOT-23,
TPS35 Top View
DDF Package,
8-Pin SOT-23,
TPS35 Top ViewTPS35
Pin Configuration Option
D
DDF Package,
8-Pin SOT-23,
TPS35 Top View
Pin Configuration Option
D
DDF Package,
8-Pin SOT-23,
TPS35 Top View
DDF Package,
8-Pin SOT-23,
TPS35 Top ViewTPS35
Pin Configuration Option
J
DSE Package,
6-Pin WSON,
TPS35 Top View
Pin Configuration Option
J
DSE Package,
6-Pin WSON,
TPS35 Top View
DSE Package,
6-Pin WSON,
TPS35 Top ViewTPS35
Pin Configuration Option
K
DSE Package,
6-Pin WSON,
TPS35 Top View
Pin Configuration Option
K
DSE Package,
6-Pin WSON,
TPS35 Top View
DSE Package,
6-Pin WSON,
TPS35 Top ViewTPS35
Pin Functions
PIN NAME
PIN NUMBER
I/O
DESCRIPTION
PINOUT A
PINOUT B
PINOUT C
PINOUT D
PINOUT J
PINOUT K
CRST
3
3
—
—
—
2
I
Programmable reset timeout pin.
Connect a capacitor between this pin and GND to program the reset
timeout period. See
for
more details.
CWD
2
2
—
—
—
1
I
Programmable watchdog timeout input. Watchdog timeout is set by
connecting a capacitor between this pin and ground. See
for
more details.
GND
4
4
4
4
4
4
—
Ground
pin
MR
1
—
2
—
—
—
I
Manual reset
pin. A logic low on this pin asserts the RESET.
See
for
more details.
RESET
7
7
7
7
5
5
O
Reset output. Connect
RESET to VDD using a pull up resistance
when using open drain output. RESET is asserted
when the voltage at the VDD pin goes below the undervoltage
threshold (VIT-) or MR pin is driven
LOW. For pinout options which do not support independent
WDO pin, RESET is also
asserted for watchdog error. See
for
more details.
SET0
5
1
1
1
1
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
SET1
—
5
5
5
—
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
VDD
8
8
8
8
6
6
I
Supply voltage
pin. For noisy systems, connecting a 0.1-µF bypass capacitor is
recommended.
WD-EN
—
—
6
2
2
—
I
Logic input.
Logic high input enables the watchdog monitoring feature. See
for
more details.
WDI
6
6
3
3
3
3
I
Watchdog input.
A falling transition (edge) must occur at this pin before the timeout expires in
order for RESET / WDO to
not assert. See
for
more details.
WDO
—
—
—
6
—
—
O
Watchdog
output. Connect WDO to VDD using pull up
resistance when using open drain output. WDO
asserts when a watchdog error occurs. WDO only
asserts when RESET is high. When a watchdog
error occurs, WDO asserts for the set
RESET timeout delay (tD). When
RESET is asserted, WDO
is deasserted and watchdog functionality is disabled. See
for
more details.
Pin Functions
PIN NAME
PIN NUMBER
I/O
DESCRIPTION
PINOUT A
PINOUT B
PINOUT C
PINOUT D
PINOUT J
PINOUT K
CRST
3
3
—
—
—
2
I
Programmable reset timeout pin.
Connect a capacitor between this pin and GND to program the reset
timeout period. See
for
more details.
CWD
2
2
—
—
—
1
I
Programmable watchdog timeout input. Watchdog timeout is set by
connecting a capacitor between this pin and ground. See
for
more details.
GND
4
4
4
4
4
4
—
Ground
pin
MR
1
—
2
—
—
—
I
Manual reset
pin. A logic low on this pin asserts the RESET.
See
for
more details.
RESET
7
7
7
7
5
5
O
Reset output. Connect
RESET to VDD using a pull up resistance
when using open drain output. RESET is asserted
when the voltage at the VDD pin goes below the undervoltage
threshold (VIT-) or MR pin is driven
LOW. For pinout options which do not support independent
WDO pin, RESET is also
asserted for watchdog error. See
for
more details.
SET0
5
1
1
1
1
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
SET1
—
5
5
5
—
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
VDD
8
8
8
8
6
6
I
Supply voltage
pin. For noisy systems, connecting a 0.1-µF bypass capacitor is
recommended.
WD-EN
—
—
6
2
2
—
I
Logic input.
Logic high input enables the watchdog monitoring feature. See
for
more details.
WDI
6
6
3
3
3
3
I
Watchdog input.
A falling transition (edge) must occur at this pin before the timeout expires in
order for RESET / WDO to
not assert. See
for
more details.
WDO
—
—
—
6
—
—
O
Watchdog
output. Connect WDO to VDD using pull up
resistance when using open drain output. WDO
asserts when a watchdog error occurs. WDO only
asserts when RESET is high. When a watchdog
error occurs, WDO asserts for the set
RESET timeout delay (tD). When
RESET is asserted, WDO
is deasserted and watchdog functionality is disabled. See
for
more details.
PIN NAME
PIN NUMBER
I/O
DESCRIPTION
PINOUT A
PINOUT B
PINOUT C
PINOUT D
PINOUT J
PINOUT K
PIN NAME
PIN NUMBER
I/O
DESCRIPTION
PIN NAMEPIN NUMBERI/ODESCRIPTION
PINOUT A
PINOUT B
PINOUT C
PINOUT D
PINOUT J
PINOUT K
PINOUT APINOUT BPINOUT CPINOUT DPINOUT JPINOUT K
CRST
3
3
—
—
—
2
I
Programmable reset timeout pin.
Connect a capacitor between this pin and GND to program the reset
timeout period. See
for
more details.
CWD
2
2
—
—
—
1
I
Programmable watchdog timeout input. Watchdog timeout is set by
connecting a capacitor between this pin and ground. See
for
more details.
GND
4
4
4
4
4
4
—
Ground
pin
MR
1
—
2
—
—
—
I
Manual reset
pin. A logic low on this pin asserts the RESET.
See
for
more details.
RESET
7
7
7
7
5
5
O
Reset output. Connect
RESET to VDD using a pull up resistance
when using open drain output. RESET is asserted
when the voltage at the VDD pin goes below the undervoltage
threshold (VIT-) or MR pin is driven
LOW. For pinout options which do not support independent
WDO pin, RESET is also
asserted for watchdog error. See
for
more details.
SET0
5
1
1
1
1
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
SET1
—
5
5
5
—
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
VDD
8
8
8
8
6
6
I
Supply voltage
pin. For noisy systems, connecting a 0.1-µF bypass capacitor is
recommended.
WD-EN
—
—
6
2
2
—
I
Logic input.
Logic high input enables the watchdog monitoring feature. See
for
more details.
WDI
6
6
3
3
3
3
I
Watchdog input.
A falling transition (edge) must occur at this pin before the timeout expires in
order for RESET / WDO to
not assert. See
for
more details.
WDO
—
—
—
6
—
—
O
Watchdog
output. Connect WDO to VDD using pull up
resistance when using open drain output. WDO
asserts when a watchdog error occurs. WDO only
asserts when RESET is high. When a watchdog
error occurs, WDO asserts for the set
RESET timeout delay (tD). When
RESET is asserted, WDO
is deasserted and watchdog functionality is disabled. See
for
more details.
CRST
3
3
—
—
—
2
I
Programmable reset timeout pin.
Connect a capacitor between this pin and GND to program the reset
timeout period. See
for
more details.
CRST33———2IProgrammable reset timeout pin.
Connect a capacitor between this pin and GND to program the reset
timeout period. See
for
more details.
CWD
2
2
—
—
—
1
I
Programmable watchdog timeout input. Watchdog timeout is set by
connecting a capacitor between this pin and ground. See
for
more details.
CWD22———1IProgrammable watchdog timeout input. Watchdog timeout is set by
connecting a capacitor between this pin and ground. See
for
more details.timeout
GND
4
4
4
4
4
4
—
Ground
pin
GND444444—Ground
pin
MR
1
—
2
—
—
—
I
Manual reset
pin. A logic low on this pin asserts the RESET.
See
for
more details.
MR
MR1—2———IManual reset
pin. A logic low on this pin asserts the RESET.
See
for
more details.RESET
RESET
7
7
7
7
5
5
O
Reset output. Connect
RESET to VDD using a pull up resistance
when using open drain output. RESET is asserted
when the voltage at the VDD pin goes below the undervoltage
threshold (VIT-) or MR pin is driven
LOW. For pinout options which do not support independent
WDO pin, RESET is also
asserted for watchdog error. See
for
more details.
RESET
RESET777755OReset output. Connect
RESET to VDD using a pull up resistance
when using open drain output. RESET is asserted
when the voltage at the VDD pin goes below the undervoltage
threshold (VIT-) or MR pin is driven
LOW. For pinout options which do not support independent
WDO pin, RESET is also
asserted for watchdog error. See
for
more details.RESETRESETIT-MRWDORESET
SET0
5
1
1
1
1
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
SET051111—ILogic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
SET1
—
5
5
5
—
—
I
Logic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
SET1—555——ILogic input.
SET0, SET1, and WD-EN pins select the watchdog and
enable-disable the watchdog; see
for
more details.
VDD
8
8
8
8
6
6
I
Supply voltage
pin. For noisy systems, connecting a 0.1-µF bypass capacitor is
recommended.
VDD888866ISupply voltage
pin. For noisy systems, connecting a 0.1-µF bypass capacitor is
recommended.
WD-EN
—
—
6
2
2
—
I
Logic input.
Logic high input enables the watchdog monitoring feature. See
for
more details.
WD-EN——622—ILogic input.
Logic high input enables the watchdog monitoring feature. See
for
more details.
WDI
6
6
3
3
3
3
I
Watchdog input.
A falling transition (edge) must occur at this pin before the timeout expires in
order for RESET / WDO to
not assert. See
for
more details.
WDI663333IWatchdog input.
A falling transition (edge) must occur at this pin before the timeout expires in
order for RESET / WDO to
not assert. See
for
more details.before the timeout expiresRESETWDO
WDO
—
—
—
6
—
—
O
Watchdog
output. Connect WDO to VDD using pull up
resistance when using open drain output. WDO
asserts when a watchdog error occurs. WDO only
asserts when RESET is high. When a watchdog
error occurs, WDO asserts for the set
RESET timeout delay (tD). When
RESET is asserted, WDO
is deasserted and watchdog functionality is disabled. See
for
more details.
WDO
WDO———6——OWatchdog
output. Connect WDO to VDD using pull up
resistance when using open drain output. WDO
asserts when a watchdog error occurs. WDO only
asserts when RESET is high. When a watchdog
error occurs, WDO asserts for the set
RESET timeout delay (tD). When
RESET is asserted, WDO
is deasserted and watchdog functionality is disabled. See
for
more details.WDOWDOWDORESETWDORESETDRESETWDO
Specifications
Absolute Maximum Ratings
over operating free-air temperature range, unless otherwise noted#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER1
MIN
MAX
UNIT
Voltage
VDD
–0.3
6.5
V
Voltage
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER3, WDO (Push Pull)
–0.3
VDD+0.3 #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/SF_WMY9TRSL1
V
RESET (Open Drain),
WDO (Open Drain)
–0.3
6.5
Current
WDO pin
–20
20
mA
Temperature #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER2
Operating ambient temperature, TA
–40
125
℃
Temperature
Storage, Tstg
–65
150
Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR.
The absolute maximum rating is (VDD + 0.3) V or 6.5 V, whichever is smaller
As a result of the low dissipated power in this device, it is assumed that TJ = TA.
ESD Ratings
VALUE
UNIT
V(ESD)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER1
± 2000
V
Charged device model (CDM), per JEDEC specification JESD22-C101#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER2
± 750
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
Voltage
VDD (Active Low output)
0.9
6
V
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244049/A_SUPERVISOR_VVCM_4_ROC_FOOTER2
0
VDD
RESET
(Open Drain) ,
WDO (Open Drain)
0
6
RESET
(Open Drain) ,
WDO (Push Pull)
0
VDD
Current
RESET,
WDO pin current
–5
5
mA
CRST
CRST pin capacitor range
1.5
1800
nF
CWD
CWD pin capacitor range
1.5
1000
nF
TA
Operating ambient temperature
–40
125
℃
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR. VMR should not be higher than VDD.
Thermal Information
THERMAL METRIC#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244050/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1
TPS35
UNIT
DDF (SOT23-8)
8 PINS
RθJA
Junction-to-ambient thermal resistance
175.3
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
94.7
°C/W
RθJB
Junction-to-board thermal resistance
92.4
°C/W
ψJT
Junction-to-top characterization parameter
8.4
°C/W
ψJB
Junction-to-board characterization parameter
91.9
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.
Thermal Information
A
Added Thermal Information table for DSE package
yes
THERMAL METRIC #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000380644/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1_SF1
TPS35
UNIT
DSE (WSON-6)
6 PINS
RθJA
Added Thermal Information table for DSE packageJunction-to-ambient thermal resistance
199.0
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
121.4
°C/W
RθJB
Junction-to-board thermal resistance
104.3
°C/W
ψJT
Junction-to-top characterization parameter
11.3
°C/W
ψJB
Junction-to-board characterization parameter
103.8
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.
Electrical Characteristics
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
COMMON PARAMETERS
VDD
Input supply voltage
Active LOW output
1.04
6
V
VIT–
Negative-going input threshold accuracy #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER1
VIT– = 1.05 V to 1.95 V
–1.4
±0.5
1.4
%
VIT– = 2.0 V to 5.4 V
–1.2
±0.5
1.2
VHYS
Hysteresis VIT– pin
VIT– = 1.05 V to 5.4 V
3
5
7
%
IDD
Supply current into VDD pin #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
VDD = 2 VVIT– = 1.05 V to 1.95 V
TA = –40℃ to 85℃
0.25
0.8
µA
0.25
3
VDD = 6 VVIT– = 1.05 V to 5.4 V
TA = –40℃ to 85℃
0.25
0.8
0.25
3
VIL
Low level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.3VDD
V
VIH
High level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.7VDD
V
R
MR
Manual reset internal pull-up resistance
100
kΩ
RESET / WDO (Open-drain active-low)
VOL
Low level output voltage
VDD =1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
mV
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
mV
Ilkg(OD)
Open-Drain output leakage current
VDD = VPULLUP = 6VTA = –40℃ to 85℃
10
30
nA
VDD = VPULLUP = 6V
10
120
nA
RESET / WDO (Push-pull active-low)
VPOR
Power on RESET voltage #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/SF6EAA7G67JT
VOL(max) = 300 mVIOUT(Sink) = 15 µA
900
mV
VOL
Low level output voltage
VDD = 0.9 V, 1.05 V ≤ VIT– ≤ 1.5 VIOUT(Sink) = 15 µA
300
mV
VDD = 1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
VOH
High level output voltage
VDD = 1.8 V, 1.05 V ≤ VIT– ≤ 1.4 VIOUT(Source) = 500 µA
0.8VDD
V
VDD = 3.3 V, 1.45 V ≤ VIT– ≤ 3.0 VIOUT(Source) = 500 µA
0.8VDD
VDD = 6 V, 3.05 V ≤ VIT– ≤ 5.4 VIOUT(Source) = 2 mA
0.8VDD
VIT– threshold voltage range from 1.05 V to 5.4 V in 50 mV steps.
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR.
VPOR is the minimum VDD voltage level for a controlled output state
Timing Requirements
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output RESET / WDO load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tGI_VIT–
Glitch immunity VIT–
5% VIT– overdrive#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER2
15
µs
t
MR_PW
MR pin pulse duration to assert reset
100
ns
tP-WD
WDI pulse duration to start next frame #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
500
ns
tHD-WDEN
WD-EN hold time to enable or disable WD operation #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
200
µs
tHD-SETx
SETx hold time to change WD timer setting #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
150
µs
tWD
Watchdog timeout period
Orderable Option TPS35xxxxB
0.8
1
1.2
ms
Orderable Option TPS35xxxxC
4
5
6
Orderable Option TPS35xxxxD
9
10
11
Orderable Option TPS35xxxxE
18
20
22
Orderable Option TPS35xxxxF
45
50
55
Orderable Option TPS35xxxxG
90
100
110
Orderable Option TPS35xxxxH
180
200
220
Orderable Option TPS35xxxxI
0.9
1
1.1
s
Orderable Option TPS35xxxxJ
1.26
1.4
1.54
Orderable Option TPS35xxxxK
1.44
1.6
1.76
Orderable Option TPS35xxxxL
9
10
11
Orderable Option TPS35xxxxM
45
50
55
Orderable Option TPS35xxxxN
90
100
110
Overdrive % = [(VDD/ VIT–) – 1] × 100%
Not production tested
Switching Characteristics
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output RESET / WDO load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tSTRT
Startup delay#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER1_SF1
500
µs
tP_HL
RESET detect delay for VDD falling below VIT–
VDD : (VIT+ + 10%) to (VIT– – 10%)#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER4_SF1
30
50
µs
tSD
Watchdog startup delay
Orderable part number TPS35xA, TPS35xG
0
ms
Orderable part number TPS35xB, TPS35xH
180
200
220
Orderable part number TPS35xC, TPS35xI
450
500
550
Orderable part number TPS35xD, TPS35xJ
0.9
1
1.1
s
Orderable part number TPS35xE, TPS35xK
4.5
5
5.5
Orderable part number TPS35xF, TPS35xL
9
10
11
tD
Reset time delay #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER3_SF1
Orderable part number TPS35xxxxxxB
1.6
2
2.4
ms
Orderable part number TPS35xxxxxxC
9
10
11
ms
Orderable part number TPS35xxxxxxD
22.5
25
27.5
ms
Orderable part number TPS35xxxxxxE
45
50
55
ms
Orderable part number TPS35xxxxxxF
90
100
110
ms
Orderable part number TPS35xxxxxxG
180
200
220
ms
Orderable part number TPS35xxxxxxH
0.9
1
1.1
s
Orderable part number TPS35xxxxxxI
9
10
11
s
tWDO
Watchdog timeout delay
tD
s
t
MR_RES
Propagation delay from MR low to reset assertion
VDD ≥ VIT– + 0.2 V,
MR = V
MR_H to V
MR_L
100
ns
t
MR_tD
Delay from MR release to reset deassert
VDD = 3.3 V,
MR = V
MR_L to V
MR_H
tD
s
tP_HL measured from threshold trip point (VIT–) to RESET assert. VIT+ = VIT– + VHYS
Specified by design parameter. When VDD starts from less than the specified minimum VDD and then exceeds VIT+, reset is deasserted after the startup delay (tSTRT) + tD delay.
VDD voltage transitions from (VIT– - 10%) to (VIT– + 10%)
Timing Diagrams
*
Added a footnote to for tINIT
no
Functional Timing Diagram
Typical Characteristics
all curves are taken at TA = 25°C
(unless otherwise noted)
VIT- Accuracy vs Temperature
VIT- Accuracy
Histogram
VIT- Hysteresis Vs Temperature
Supply Glitch Immunity vs Overdrive
Timer Accuracy vs
Temperature
Timer Accuracy Histogram
tWD vs Capacitance
tD vs Capacitance
RESET VOL vs I
sink, VDD = 1.5 V
WDO VOL vs I
sink, VDD = 1.5 V
RESET VOL vs I sink, VDD = 3.3 V
WDO VOL vs I sink, VDD = 3.3 V
RESET VOH vs I source, VDD = 2.0 V
WDO VOH vs I source, VDD = 2.0 V
RESET VOH vs I source, VDD = 6.0 V
WDO VOH vs I source, VDD = 6.0 V
Supply Current
vs Power-Supply Voltage
Specifications
Absolute Maximum Ratings
over operating free-air temperature range, unless otherwise noted#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER1
MIN
MAX
UNIT
Voltage
VDD
–0.3
6.5
V
Voltage
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER3, WDO (Push Pull)
–0.3
VDD+0.3 #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/SF_WMY9TRSL1
V
RESET (Open Drain),
WDO (Open Drain)
–0.3
6.5
Current
WDO pin
–20
20
mA
Temperature #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER2
Operating ambient temperature, TA
–40
125
℃
Temperature
Storage, Tstg
–65
150
Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR.
The absolute maximum rating is (VDD + 0.3) V or 6.5 V, whichever is smaller
As a result of the low dissipated power in this device, it is assumed that TJ = TA.
Absolute Maximum Ratings
over operating free-air temperature range, unless otherwise noted#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER1
MIN
MAX
UNIT
Voltage
VDD
–0.3
6.5
V
Voltage
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER3, WDO (Push Pull)
–0.3
VDD+0.3 #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/SF_WMY9TRSL1
V
RESET (Open Drain),
WDO (Open Drain)
–0.3
6.5
Current
WDO pin
–20
20
mA
Temperature #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER2
Operating ambient temperature, TA
–40
125
℃
Temperature
Storage, Tstg
–65
150
Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR.
The absolute maximum rating is (VDD + 0.3) V or 6.5 V, whichever is smaller
As a result of the low dissipated power in this device, it is assumed that TJ = TA.
over operating free-air temperature range, unless otherwise noted#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER1
MIN
MAX
UNIT
Voltage
VDD
–0.3
6.5
V
Voltage
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER3, WDO (Push Pull)
–0.3
VDD+0.3 #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/SF_WMY9TRSL1
V
RESET (Open Drain),
WDO (Open Drain)
–0.3
6.5
Current
WDO pin
–20
20
mA
Temperature #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER2
Operating ambient temperature, TA
–40
125
℃
Temperature
Storage, Tstg
–65
150
over operating free-air temperature range, unless otherwise noted#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER1
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER1
MIN
MAX
UNIT
Voltage
VDD
–0.3
6.5
V
Voltage
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER3, WDO (Push Pull)
–0.3
VDD+0.3 #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/SF_WMY9TRSL1
V
RESET (Open Drain),
WDO (Open Drain)
–0.3
6.5
Current
WDO pin
–20
20
mA
Temperature #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER2
Operating ambient temperature, TA
–40
125
℃
Temperature
Storage, Tstg
–65
150
MIN
MAX
UNIT
MIN
MAX
UNIT
MINMAXUNIT
Voltage
VDD
–0.3
6.5
V
Voltage
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER3, WDO (Push Pull)
–0.3
VDD+0.3 #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/SF_WMY9TRSL1
V
RESET (Open Drain),
WDO (Open Drain)
–0.3
6.5
Current
WDO pin
–20
20
mA
Temperature #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER2
Operating ambient temperature, TA
–40
125
℃
Temperature
Storage, Tstg
–65
150
Voltage
VDD
–0.3
6.5
V
VoltageVDD–0.36.5V
Voltage
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER3, WDO (Push Pull)
–0.3
VDD+0.3 #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/SF_WMY9TRSL1
V
VoltageCWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER3, WDO (Push Pull)WDRSTMR#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER3WDO–0.3VDD+0.3 #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/SF_WMY9TRSL1
DD#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/SF_WMY9TRSL1V
RESET (Open Drain),
WDO (Open Drain)
–0.3
6.5
RESET (Open Drain),
WDO (Open Drain)
RESET (Open Drain), RESET
WDO (Open Drain)WDO–0.36.5
Current
WDO pin
–20
20
mA
Current WDO pinWDO–2020mA
Temperature #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER2
Operating ambient temperature, TA
–40
125
℃
Temperature #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER2
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244046/A_SUPERVISOR_VVCM_1_ABSMAX_FOOTER2Operating ambient temperature, TA
A–40125℃
Temperature
Storage, Tstg
–65
150
TemperatureStorage, Tstg
stg–65150
Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR.
The absolute maximum rating is (VDD + 0.3) V or 6.5 V, whichever is smaller
As a result of the low dissipated power in this device, it is assumed that TJ = TA.
Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.Absolute Maximum RatingRecommended Operating ConditionIf the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR. MRDDDDMRThe absolute maximum rating is (VDD + 0.3) V or 6.5 V, whichever is smallerAs a result of the low dissipated power in this device, it is assumed that TJ = TA.JA
ESD Ratings
VALUE
UNIT
V(ESD)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER1
± 2000
V
Charged device model (CDM), per JEDEC specification JESD22-C101#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER2
± 750
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
ESD Ratings
VALUE
UNIT
V(ESD)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER1
± 2000
V
Charged device model (CDM), per JEDEC specification JESD22-C101#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER2
± 750
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
VALUE
UNIT
V(ESD)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER1
± 2000
V
Charged device model (CDM), per JEDEC specification JESD22-C101#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER2
± 750
VALUE
UNIT
V(ESD)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER1
± 2000
V
Charged device model (CDM), per JEDEC specification JESD22-C101#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER2
± 750
VALUE
UNIT
VALUE
UNIT
VALUEUNIT
V(ESD)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER1
± 2000
V
Charged device model (CDM), per JEDEC specification JESD22-C101#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER2
± 750
V(ESD)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER1
± 2000
V
V(ESD)
(ESD)Electrostatic dischargeHuman body model (HBM), per ANSI/ESDA/JEDEC JS-001#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER1
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER1± 2000V
Charged device model (CDM), per JEDEC specification JESD22-C101#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER2
± 750
Charged device model (CDM), per JEDEC specification JESD22-C101#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER2
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244047/A_SUPERVISOR_VVCM_2_ESD_RATINGS_INDUSTRIAL_FOOTER2± 750
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
Voltage
VDD (Active Low output)
0.9
6
V
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244049/A_SUPERVISOR_VVCM_4_ROC_FOOTER2
0
VDD
RESET
(Open Drain) ,
WDO (Open Drain)
0
6
RESET
(Open Drain) ,
WDO (Push Pull)
0
VDD
Current
RESET,
WDO pin current
–5
5
mA
CRST
CRST pin capacitor range
1.5
1800
nF
CWD
CWD pin capacitor range
1.5
1000
nF
TA
Operating ambient temperature
–40
125
℃
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR. VMR should not be higher than VDD.
Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
Voltage
VDD (Active Low output)
0.9
6
V
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244049/A_SUPERVISOR_VVCM_4_ROC_FOOTER2
0
VDD
RESET
(Open Drain) ,
WDO (Open Drain)
0
6
RESET
(Open Drain) ,
WDO (Push Pull)
0
VDD
Current
RESET,
WDO pin current
–5
5
mA
CRST
CRST pin capacitor range
1.5
1800
nF
CWD
CWD pin capacitor range
1.5
1000
nF
TA
Operating ambient temperature
–40
125
℃
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR. VMR should not be higher than VDD.
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
Voltage
VDD (Active Low output)
0.9
6
V
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244049/A_SUPERVISOR_VVCM_4_ROC_FOOTER2
0
VDD
RESET
(Open Drain) ,
WDO (Open Drain)
0
6
RESET
(Open Drain) ,
WDO (Push Pull)
0
VDD
Current
RESET,
WDO pin current
–5
5
mA
CRST
CRST pin capacitor range
1.5
1800
nF
CWD
CWD pin capacitor range
1.5
1000
nF
TA
Operating ambient temperature
–40
125
℃
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
Voltage
VDD (Active Low output)
0.9
6
V
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244049/A_SUPERVISOR_VVCM_4_ROC_FOOTER2
0
VDD
RESET
(Open Drain) ,
WDO (Open Drain)
0
6
RESET
(Open Drain) ,
WDO (Push Pull)
0
VDD
Current
RESET,
WDO pin current
–5
5
mA
CRST
CRST pin capacitor range
1.5
1800
nF
CWD
CWD pin capacitor range
1.5
1000
nF
TA
Operating ambient temperature
–40
125
℃
MIN
NOM
MAX
UNIT
MIN
NOM
MAX
UNIT
MINNOMMAXUNIT
Voltage
VDD (Active Low output)
0.9
6
V
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244049/A_SUPERVISOR_VVCM_4_ROC_FOOTER2
0
VDD
RESET
(Open Drain) ,
WDO (Open Drain)
0
6
RESET
(Open Drain) ,
WDO (Push Pull)
0
VDD
Current
RESET,
WDO pin current
–5
5
mA
CRST
CRST pin capacitor range
1.5
1800
nF
CWD
CWD pin capacitor range
1.5
1000
nF
TA
Operating ambient temperature
–40
125
℃
Voltage
VDD (Active Low output)
0.9
6
V
VoltageVDD (Active Low output)0.96V
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244049/A_SUPERVISOR_VVCM_4_ROC_FOOTER2
0
VDD
CWD, CRST, WD–EN, SETx, WDI, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244049/A_SUPERVISOR_VVCM_4_ROC_FOOTER2
WDRSTMR#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244049/A_SUPERVISOR_VVCM_4_ROC_FOOTER20VDD
RESET
(Open Drain) ,
WDO (Open Drain)
0
6
RESET
(Open Drain) ,
WDO (Open Drain)
RESET
RESET (Open Drain) ,WDO06
RESET
(Open Drain) ,
WDO (Push Pull)
0
VDD
RESET
(Open Drain) ,
WDO (Push Pull)
RESET
RESET(Open Drain) ,WDO0VDD
Current
RESET,
WDO pin current
–5
5
mA
Current
RESET,
WDO pin current
RESET,RESETWDO–55mA
CRST
CRST pin capacitor range
1.5
1800
nF
CRST
RSTCRST pin capacitor rangeRST1.51800nF
CWD
CWD pin capacitor range
1.5
1000
nF
CWD
WDCWD pin capacitor rangeWD1.51000nF
TA
Operating ambient temperature
–40
125
℃
TA
AOperating ambient temperature–40125℃
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR. VMR should not be higher than VDD.
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR. VMR should not be higher than VDD.
MRDDDDMRMRDD.
Thermal Information
THERMAL METRIC#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244050/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1
TPS35
UNIT
DDF (SOT23-8)
8 PINS
RθJA
Junction-to-ambient thermal resistance
175.3
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
94.7
°C/W
RθJB
Junction-to-board thermal resistance
92.4
°C/W
ψJT
Junction-to-top characterization parameter
8.4
°C/W
ψJB
Junction-to-board characterization parameter
91.9
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.
Thermal Information
THERMAL METRIC#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244050/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1
TPS35
UNIT
DDF (SOT23-8)
8 PINS
RθJA
Junction-to-ambient thermal resistance
175.3
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
94.7
°C/W
RθJB
Junction-to-board thermal resistance
92.4
°C/W
ψJT
Junction-to-top characterization parameter
8.4
°C/W
ψJB
Junction-to-board characterization parameter
91.9
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.
THERMAL METRIC#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244050/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1
TPS35
UNIT
DDF (SOT23-8)
8 PINS
RθJA
Junction-to-ambient thermal resistance
175.3
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
94.7
°C/W
RθJB
Junction-to-board thermal resistance
92.4
°C/W
ψJT
Junction-to-top characterization parameter
8.4
°C/W
ψJB
Junction-to-board characterization parameter
91.9
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
THERMAL METRIC#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244050/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1
TPS35
UNIT
DDF (SOT23-8)
8 PINS
RθJA
Junction-to-ambient thermal resistance
175.3
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
94.7
°C/W
RθJB
Junction-to-board thermal resistance
92.4
°C/W
ψJT
Junction-to-top characterization parameter
8.4
°C/W
ψJB
Junction-to-board characterization parameter
91.9
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
THERMAL METRIC#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244050/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1
TPS35
UNIT
DDF (SOT23-8)
8 PINS
THERMAL METRIC#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244050/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1
TPS35
UNIT
THERMAL METRIC#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244050/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244050/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1
TPS35
TPS35UNIT
DDF (SOT23-8)
DDF (SOT23-8)
8 PINS
8 PINS
RθJA
Junction-to-ambient thermal resistance
175.3
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
94.7
°C/W
RθJB
Junction-to-board thermal resistance
92.4
°C/W
ψJT
Junction-to-top characterization parameter
8.4
°C/W
ψJB
Junction-to-board characterization parameter
91.9
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
RθJA
Junction-to-ambient thermal resistance
175.3
°C/W
RθJA
θJAJunction-to-ambient thermal resistance175.3°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
94.7
°C/W
RθJC(top)
θJC(top)Junction-to-case (top) thermal resistance94.7°C/W
RθJB
Junction-to-board thermal resistance
92.4
°C/W
RθJB
θJBJunction-to-board thermal resistance92.4°C/W
ψJT
Junction-to-top characterization parameter
8.4
°C/W
ψJT
JTJunction-to-top characterization parameter8.4°C/W
ψJB
Junction-to-board characterization parameter
91.9
°C/W
ψJB
JBJunction-to-board characterization parameter91.9°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
RθJC(bot)
θJC(bot)Junction-to-case (bottom) thermal resistanceN/A°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.Semiconductor and IC Package Thermal Metrics
Thermal Information
A
Added Thermal Information table for DSE package
yes
THERMAL METRIC #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000380644/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1_SF1
TPS35
UNIT
DSE (WSON-6)
6 PINS
RθJA
Added Thermal Information table for DSE packageJunction-to-ambient thermal resistance
199.0
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
121.4
°C/W
RθJB
Junction-to-board thermal resistance
104.3
°C/W
ψJT
Junction-to-top characterization parameter
11.3
°C/W
ψJB
Junction-to-board characterization parameter
103.8
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.
Thermal Information
A
Added Thermal Information table for DSE package
yes
A
Added Thermal Information table for DSE package
yes
A
Added Thermal Information table for DSE package
yes
AAdded Thermal Information table for DSE packageyes
THERMAL METRIC #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000380644/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1_SF1
TPS35
UNIT
DSE (WSON-6)
6 PINS
RθJA
Added Thermal Information table for DSE packageJunction-to-ambient thermal resistance
199.0
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
121.4
°C/W
RθJB
Junction-to-board thermal resistance
104.3
°C/W
ψJT
Junction-to-top characterization parameter
11.3
°C/W
ψJB
Junction-to-board characterization parameter
103.8
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.
THERMAL METRIC #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000380644/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1_SF1
TPS35
UNIT
DSE (WSON-6)
6 PINS
RθJA
Added Thermal Information table for DSE packageJunction-to-ambient thermal resistance
199.0
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
121.4
°C/W
RθJB
Junction-to-board thermal resistance
104.3
°C/W
ψJT
Junction-to-top characterization parameter
11.3
°C/W
ψJB
Junction-to-board characterization parameter
103.8
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
THERMAL METRIC #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000380644/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1_SF1
TPS35
UNIT
DSE (WSON-6)
6 PINS
RθJA
Added Thermal Information table for DSE packageJunction-to-ambient thermal resistance
199.0
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
121.4
°C/W
RθJB
Junction-to-board thermal resistance
104.3
°C/W
ψJT
Junction-to-top characterization parameter
11.3
°C/W
ψJB
Junction-to-board characterization parameter
103.8
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
THERMAL METRIC #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000380644/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1_SF1
TPS35
UNIT
DSE (WSON-6)
6 PINS
THERMAL METRIC #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000380644/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1_SF1
TPS35
UNIT
THERMAL METRIC #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000380644/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1_SF1
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000380644/A_SUPERVISOR_VVCM_5_THERMAL_FOOTER1_SF1
TPS35
TPS35UNIT
DSE (WSON-6)
DSE (WSON-6)
6 PINS
6 PINS
RθJA
Added Thermal Information table for DSE packageJunction-to-ambient thermal resistance
199.0
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
121.4
°C/W
RθJB
Junction-to-board thermal resistance
104.3
°C/W
ψJT
Junction-to-top characterization parameter
11.3
°C/W
ψJB
Junction-to-board characterization parameter
103.8
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
RθJA
Added Thermal Information table for DSE packageJunction-to-ambient thermal resistance
199.0
°C/W
RθJA
θJA
Added Thermal Information table for DSE packageJunction-to-ambient thermal resistanceAdded Thermal Information table for DSE package199.0°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
121.4
°C/W
RθJC(top)
θJC(top)Junction-to-case (top) thermal resistance121.4°C/W
RθJB
Junction-to-board thermal resistance
104.3
°C/W
RθJB
θJBJunction-to-board thermal resistance104.3°C/W
ψJT
Junction-to-top characterization parameter
11.3
°C/W
ψJT
JTJunction-to-top characterization parameter11.3°C/W
ψJB
Junction-to-board characterization parameter
103.8
°C/W
ψJB
JBJunction-to-board characterization parameter103.8°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
RθJC(bot)
θJC(bot)Junction-to-case (bottom) thermal resistanceN/A°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.Semiconductor and IC Package Thermal Metrics
Electrical Characteristics
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
COMMON PARAMETERS
VDD
Input supply voltage
Active LOW output
1.04
6
V
VIT–
Negative-going input threshold accuracy #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER1
VIT– = 1.05 V to 1.95 V
–1.4
±0.5
1.4
%
VIT– = 2.0 V to 5.4 V
–1.2
±0.5
1.2
VHYS
Hysteresis VIT– pin
VIT– = 1.05 V to 5.4 V
3
5
7
%
IDD
Supply current into VDD pin #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
VDD = 2 VVIT– = 1.05 V to 1.95 V
TA = –40℃ to 85℃
0.25
0.8
µA
0.25
3
VDD = 6 VVIT– = 1.05 V to 5.4 V
TA = –40℃ to 85℃
0.25
0.8
0.25
3
VIL
Low level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.3VDD
V
VIH
High level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.7VDD
V
R
MR
Manual reset internal pull-up resistance
100
kΩ
RESET / WDO (Open-drain active-low)
VOL
Low level output voltage
VDD =1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
mV
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
mV
Ilkg(OD)
Open-Drain output leakage current
VDD = VPULLUP = 6VTA = –40℃ to 85℃
10
30
nA
VDD = VPULLUP = 6V
10
120
nA
RESET / WDO (Push-pull active-low)
VPOR
Power on RESET voltage #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/SF6EAA7G67JT
VOL(max) = 300 mVIOUT(Sink) = 15 µA
900
mV
VOL
Low level output voltage
VDD = 0.9 V, 1.05 V ≤ VIT– ≤ 1.5 VIOUT(Sink) = 15 µA
300
mV
VDD = 1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
VOH
High level output voltage
VDD = 1.8 V, 1.05 V ≤ VIT– ≤ 1.4 VIOUT(Source) = 500 µA
0.8VDD
V
VDD = 3.3 V, 1.45 V ≤ VIT– ≤ 3.0 VIOUT(Source) = 500 µA
0.8VDD
VDD = 6 V, 3.05 V ≤ VIT– ≤ 5.4 VIOUT(Source) = 2 mA
0.8VDD
VIT– threshold voltage range from 1.05 V to 5.4 V in 50 mV steps.
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR.
VPOR is the minimum VDD voltage level for a controlled output state
Electrical Characteristics
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
COMMON PARAMETERS
VDD
Input supply voltage
Active LOW output
1.04
6
V
VIT–
Negative-going input threshold accuracy #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER1
VIT– = 1.05 V to 1.95 V
–1.4
±0.5
1.4
%
VIT– = 2.0 V to 5.4 V
–1.2
±0.5
1.2
VHYS
Hysteresis VIT– pin
VIT– = 1.05 V to 5.4 V
3
5
7
%
IDD
Supply current into VDD pin #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
VDD = 2 VVIT– = 1.05 V to 1.95 V
TA = –40℃ to 85℃
0.25
0.8
µA
0.25
3
VDD = 6 VVIT– = 1.05 V to 5.4 V
TA = –40℃ to 85℃
0.25
0.8
0.25
3
VIL
Low level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.3VDD
V
VIH
High level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.7VDD
V
R
MR
Manual reset internal pull-up resistance
100
kΩ
RESET / WDO (Open-drain active-low)
VOL
Low level output voltage
VDD =1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
mV
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
mV
Ilkg(OD)
Open-Drain output leakage current
VDD = VPULLUP = 6VTA = –40℃ to 85℃
10
30
nA
VDD = VPULLUP = 6V
10
120
nA
RESET / WDO (Push-pull active-low)
VPOR
Power on RESET voltage #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/SF6EAA7G67JT
VOL(max) = 300 mVIOUT(Sink) = 15 µA
900
mV
VOL
Low level output voltage
VDD = 0.9 V, 1.05 V ≤ VIT– ≤ 1.5 VIOUT(Sink) = 15 µA
300
mV
VDD = 1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
VOH
High level output voltage
VDD = 1.8 V, 1.05 V ≤ VIT– ≤ 1.4 VIOUT(Source) = 500 µA
0.8VDD
V
VDD = 3.3 V, 1.45 V ≤ VIT– ≤ 3.0 VIOUT(Source) = 500 µA
0.8VDD
VDD = 6 V, 3.05 V ≤ VIT– ≤ 5.4 VIOUT(Source) = 2 mA
0.8VDD
VIT– threshold voltage range from 1.05 V to 5.4 V in 50 mV steps.
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR.
VPOR is the minimum VDD voltage level for a controlled output state
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
COMMON PARAMETERS
VDD
Input supply voltage
Active LOW output
1.04
6
V
VIT–
Negative-going input threshold accuracy #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER1
VIT– = 1.05 V to 1.95 V
–1.4
±0.5
1.4
%
VIT– = 2.0 V to 5.4 V
–1.2
±0.5
1.2
VHYS
Hysteresis VIT– pin
VIT– = 1.05 V to 5.4 V
3
5
7
%
IDD
Supply current into VDD pin #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
VDD = 2 VVIT– = 1.05 V to 1.95 V
TA = –40℃ to 85℃
0.25
0.8
µA
0.25
3
VDD = 6 VVIT– = 1.05 V to 5.4 V
TA = –40℃ to 85℃
0.25
0.8
0.25
3
VIL
Low level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.3VDD
V
VIH
High level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.7VDD
V
R
MR
Manual reset internal pull-up resistance
100
kΩ
RESET / WDO (Open-drain active-low)
VOL
Low level output voltage
VDD =1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
mV
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
mV
Ilkg(OD)
Open-Drain output leakage current
VDD = VPULLUP = 6VTA = –40℃ to 85℃
10
30
nA
VDD = VPULLUP = 6V
10
120
nA
RESET / WDO (Push-pull active-low)
VPOR
Power on RESET voltage #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/SF6EAA7G67JT
VOL(max) = 300 mVIOUT(Sink) = 15 µA
900
mV
VOL
Low level output voltage
VDD = 0.9 V, 1.05 V ≤ VIT– ≤ 1.5 VIOUT(Sink) = 15 µA
300
mV
VDD = 1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
VOH
High level output voltage
VDD = 1.8 V, 1.05 V ≤ VIT– ≤ 1.4 VIOUT(Source) = 500 µA
0.8VDD
V
VDD = 3.3 V, 1.45 V ≤ VIT– ≤ 3.0 VIOUT(Source) = 500 µA
0.8VDD
VDD = 6 V, 3.05 V ≤ VIT– ≤ 5.4 VIOUT(Source) = 2 mA
0.8VDD
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃DDMR RESETpull-upWDOpull-upLOADA
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
COMMON PARAMETERS
VDD
Input supply voltage
Active LOW output
1.04
6
V
VIT–
Negative-going input threshold accuracy #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER1
VIT– = 1.05 V to 1.95 V
–1.4
±0.5
1.4
%
VIT– = 2.0 V to 5.4 V
–1.2
±0.5
1.2
VHYS
Hysteresis VIT– pin
VIT– = 1.05 V to 5.4 V
3
5
7
%
IDD
Supply current into VDD pin #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
VDD = 2 VVIT– = 1.05 V to 1.95 V
TA = –40℃ to 85℃
0.25
0.8
µA
0.25
3
VDD = 6 VVIT– = 1.05 V to 5.4 V
TA = –40℃ to 85℃
0.25
0.8
0.25
3
VIL
Low level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.3VDD
V
VIH
High level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.7VDD
V
R
MR
Manual reset internal pull-up resistance
100
kΩ
RESET / WDO (Open-drain active-low)
VOL
Low level output voltage
VDD =1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
mV
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
mV
Ilkg(OD)
Open-Drain output leakage current
VDD = VPULLUP = 6VTA = –40℃ to 85℃
10
30
nA
VDD = VPULLUP = 6V
10
120
nA
RESET / WDO (Push-pull active-low)
VPOR
Power on RESET voltage #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/SF6EAA7G67JT
VOL(max) = 300 mVIOUT(Sink) = 15 µA
900
mV
VOL
Low level output voltage
VDD = 0.9 V, 1.05 V ≤ VIT– ≤ 1.5 VIOUT(Sink) = 15 µA
300
mV
VDD = 1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
VOH
High level output voltage
VDD = 1.8 V, 1.05 V ≤ VIT– ≤ 1.4 VIOUT(Source) = 500 µA
0.8VDD
V
VDD = 3.3 V, 1.45 V ≤ VIT– ≤ 3.0 VIOUT(Source) = 500 µA
0.8VDD
VDD = 6 V, 3.05 V ≤ VIT– ≤ 5.4 VIOUT(Source) = 2 mA
0.8VDD
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
PARAMETERTEST CONDITIONSMINTYPMAXUNIT
COMMON PARAMETERS
VDD
Input supply voltage
Active LOW output
1.04
6
V
VIT–
Negative-going input threshold accuracy #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER1
VIT– = 1.05 V to 1.95 V
–1.4
±0.5
1.4
%
VIT– = 2.0 V to 5.4 V
–1.2
±0.5
1.2
VHYS
Hysteresis VIT– pin
VIT– = 1.05 V to 5.4 V
3
5
7
%
IDD
Supply current into VDD pin #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
VDD = 2 VVIT– = 1.05 V to 1.95 V
TA = –40℃ to 85℃
0.25
0.8
µA
0.25
3
VDD = 6 VVIT– = 1.05 V to 5.4 V
TA = –40℃ to 85℃
0.25
0.8
0.25
3
VIL
Low level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.3VDD
V
VIH
High level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.7VDD
V
R
MR
Manual reset internal pull-up resistance
100
kΩ
RESET / WDO (Open-drain active-low)
VOL
Low level output voltage
VDD =1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
mV
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
mV
Ilkg(OD)
Open-Drain output leakage current
VDD = VPULLUP = 6VTA = –40℃ to 85℃
10
30
nA
VDD = VPULLUP = 6V
10
120
nA
RESET / WDO (Push-pull active-low)
VPOR
Power on RESET voltage #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/SF6EAA7G67JT
VOL(max) = 300 mVIOUT(Sink) = 15 µA
900
mV
VOL
Low level output voltage
VDD = 0.9 V, 1.05 V ≤ VIT– ≤ 1.5 VIOUT(Sink) = 15 µA
300
mV
VDD = 1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
VOH
High level output voltage
VDD = 1.8 V, 1.05 V ≤ VIT– ≤ 1.4 VIOUT(Source) = 500 µA
0.8VDD
V
VDD = 3.3 V, 1.45 V ≤ VIT– ≤ 3.0 VIOUT(Source) = 500 µA
0.8VDD
VDD = 6 V, 3.05 V ≤ VIT– ≤ 5.4 VIOUT(Source) = 2 mA
0.8VDD
COMMON PARAMETERS
COMMON PARAMETERS
VDD
Input supply voltage
Active LOW output
1.04
6
V
VDD
DDInput supply voltageActive LOW output1.046V
VIT–
Negative-going input threshold accuracy #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER1
VIT– = 1.05 V to 1.95 V
–1.4
±0.5
1.4
%
VIT–
IT–Negative-going input threshold accuracy #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER1
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER1VIT– = 1.05 V to 1.95 VIT––1.4±0.51.4%
VIT– = 2.0 V to 5.4 V
–1.2
±0.5
1.2
VIT– = 2.0 V to 5.4 VIT––1.2±0.51.2
VHYS
Hysteresis VIT– pin
VIT– = 1.05 V to 5.4 V
3
5
7
%
VHYS
HYSHysteresis VIT– pinIT–VIT– = 1.05 V to 5.4 VIT–357%
IDD
Supply current into VDD pin #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
VDD = 2 VVIT– = 1.05 V to 1.95 V
TA = –40℃ to 85℃
0.25
0.8
µA
IDD
DDSupply current into VDD pin #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5VDD = 2 VVIT– = 1.05 V to 1.95 VDDIT–TA = –40℃ to 85℃ A0.250.8µA
0.25
3
0.253
VDD = 6 VVIT– = 1.05 V to 5.4 V
TA = –40℃ to 85℃
0.25
0.8
VDD = 6 VVIT– = 1.05 V to 5.4 VDDIT–TA = –40℃ to 85℃ A0.250.8
0.25
3
0.253
VIL
Low level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.3VDD
V
VIL
ILLow level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
MR#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER50.3VDD
DDV
VIH
High level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
0.7VDD
V
VIH
IHHigh level input voltage WD–EN, WDI, SETx, MR
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER5
MR#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/A_SUPERVISOR_VVCM_6_ELECTCHAR_FOOTER50.7VDD
DDV
R
MR
Manual reset internal pull-up resistance
100
kΩ
R
MR
MR
MRManual reset internal pull-up resistance100kΩ
RESET / WDO (Open-drain active-low)
RESET / WDO (Open-drain active-low)RESETWDO
VOL
Low level output voltage
VDD =1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
mV
VOL
OLLow level output voltage VDD =1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µADDIT–OUT(Sink)300mV
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
mV
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mADDIT–OUT(Sink)300mV
Ilkg(OD)
Open-Drain output leakage current
VDD = VPULLUP = 6VTA = –40℃ to 85℃
10
30
nA
Ilkg(OD)
lkg(OD)Open-Drain output leakage currentVDD = VPULLUP = 6VTA = –40℃ to 85℃DDPULLUPA1030nA
VDD = VPULLUP = 6V
10
120
nA
VDD = VPULLUP = 6VDDPULLUP10120nA
RESET / WDO (Push-pull active-low)
RESET / WDO (Push-pull active-low)RESETWDO
VPOR
Power on RESET voltage #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/SF6EAA7G67JT
VOL(max) = 300 mVIOUT(Sink) = 15 µA
900
mV
VPOR
PORPower on RESET voltage #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/SF6EAA7G67JT
RESET#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244051/SF6EAA7G67JTVOL(max) = 300 mVIOUT(Sink) = 15 µAOL(max)OUT(Sink)900mV
VOL
Low level output voltage
VDD = 0.9 V, 1.05 V ≤ VIT– ≤ 1.5 VIOUT(Sink) = 15 µA
300
mV
VOL
OLLow level output voltage VDD = 0.9 V, 1.05 V ≤ VIT– ≤ 1.5 VIOUT(Sink) = 15 µADDIT–OUT(Sink)300mV
VDD = 1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µA
300
VDD = 1.5 V, 1.55 V ≤ VIT– ≤ 3.35 VIOUT(Sink) = 500 µADDIT–OUT(Sink)300
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mA
300
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.4 VIOUT(Sink) = 2 mADDIT–OUT(Sink)300
VOH
High level output voltage
VDD = 1.8 V, 1.05 V ≤ VIT– ≤ 1.4 VIOUT(Source) = 500 µA
0.8VDD
V
VOH
OHHigh level output voltage VDD = 1.8 V, 1.05 V ≤ VIT– ≤ 1.4 VIOUT(Source) = 500 µADD IT–OUT(Source)0.8VDD
DDV
VDD = 3.3 V, 1.45 V ≤ VIT– ≤ 3.0 VIOUT(Source) = 500 µA
0.8VDD
VDD = 3.3 V, 1.45 V ≤ VIT– ≤ 3.0 VIOUT(Source) = 500 µADD IT–OUT(Source)0.8VDD
DD
VDD = 6 V, 3.05 V ≤ VIT– ≤ 5.4 VIOUT(Source) = 2 mA
0.8VDD
VDD = 6 V, 3.05 V ≤ VIT– ≤ 5.4 VIOUT(Source) = 2 mADD IT–OUT(Source)0.8VDD
DD
VIT– threshold voltage range from 1.05 V to 5.4 V in 50 mV steps.
If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR.
VPOR is the minimum VDD voltage level for a controlled output state
VIT– threshold voltage range from 1.05 V to 5.4 V in 50 mV steps.IT–If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR.MRDDDD MRVPOR is the minimum VDD voltage level for a controlled output statePORDD
Timing Requirements
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output RESET / WDO load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tGI_VIT–
Glitch immunity VIT–
5% VIT– overdrive#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER2
15
µs
t
MR_PW
MR pin pulse duration to assert reset
100
ns
tP-WD
WDI pulse duration to start next frame #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
500
ns
tHD-WDEN
WD-EN hold time to enable or disable WD operation #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
200
µs
tHD-SETx
SETx hold time to change WD timer setting #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
150
µs
tWD
Watchdog timeout period
Orderable Option TPS35xxxxB
0.8
1
1.2
ms
Orderable Option TPS35xxxxC
4
5
6
Orderable Option TPS35xxxxD
9
10
11
Orderable Option TPS35xxxxE
18
20
22
Orderable Option TPS35xxxxF
45
50
55
Orderable Option TPS35xxxxG
90
100
110
Orderable Option TPS35xxxxH
180
200
220
Orderable Option TPS35xxxxI
0.9
1
1.1
s
Orderable Option TPS35xxxxJ
1.26
1.4
1.54
Orderable Option TPS35xxxxK
1.44
1.6
1.76
Orderable Option TPS35xxxxL
9
10
11
Orderable Option TPS35xxxxM
45
50
55
Orderable Option TPS35xxxxN
90
100
110
Overdrive % = [(VDD/ VIT–) – 1] × 100%
Not production tested
Timing Requirements
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output RESET / WDO load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tGI_VIT–
Glitch immunity VIT–
5% VIT– overdrive#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER2
15
µs
t
MR_PW
MR pin pulse duration to assert reset
100
ns
tP-WD
WDI pulse duration to start next frame #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
500
ns
tHD-WDEN
WD-EN hold time to enable or disable WD operation #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
200
µs
tHD-SETx
SETx hold time to change WD timer setting #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
150
µs
tWD
Watchdog timeout period
Orderable Option TPS35xxxxB
0.8
1
1.2
ms
Orderable Option TPS35xxxxC
4
5
6
Orderable Option TPS35xxxxD
9
10
11
Orderable Option TPS35xxxxE
18
20
22
Orderable Option TPS35xxxxF
45
50
55
Orderable Option TPS35xxxxG
90
100
110
Orderable Option TPS35xxxxH
180
200
220
Orderable Option TPS35xxxxI
0.9
1
1.1
s
Orderable Option TPS35xxxxJ
1.26
1.4
1.54
Orderable Option TPS35xxxxK
1.44
1.6
1.76
Orderable Option TPS35xxxxL
9
10
11
Orderable Option TPS35xxxxM
45
50
55
Orderable Option TPS35xxxxN
90
100
110
Overdrive % = [(VDD/ VIT–) – 1] × 100%
Not production tested
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output RESET / WDO load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tGI_VIT–
Glitch immunity VIT–
5% VIT– overdrive#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER2
15
µs
t
MR_PW
MR pin pulse duration to assert reset
100
ns
tP-WD
WDI pulse duration to start next frame #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
500
ns
tHD-WDEN
WD-EN hold time to enable or disable WD operation #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
200
µs
tHD-SETx
SETx hold time to change WD timer setting #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
150
µs
tWD
Watchdog timeout period
Orderable Option TPS35xxxxB
0.8
1
1.2
ms
Orderable Option TPS35xxxxC
4
5
6
Orderable Option TPS35xxxxD
9
10
11
Orderable Option TPS35xxxxE
18
20
22
Orderable Option TPS35xxxxF
45
50
55
Orderable Option TPS35xxxxG
90
100
110
Orderable Option TPS35xxxxH
180
200
220
Orderable Option TPS35xxxxI
0.9
1
1.1
s
Orderable Option TPS35xxxxJ
1.26
1.4
1.54
Orderable Option TPS35xxxxK
1.44
1.6
1.76
Orderable Option TPS35xxxxL
9
10
11
Orderable Option TPS35xxxxM
45
50
55
Orderable Option TPS35xxxxN
90
100
110
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output RESET / WDO load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃DDMR RESETpull-upWDOpull-upLOADA
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tGI_VIT–
Glitch immunity VIT–
5% VIT– overdrive#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER2
15
µs
t
MR_PW
MR pin pulse duration to assert reset
100
ns
tP-WD
WDI pulse duration to start next frame #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
500
ns
tHD-WDEN
WD-EN hold time to enable or disable WD operation #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
200
µs
tHD-SETx
SETx hold time to change WD timer setting #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
150
µs
tWD
Watchdog timeout period
Orderable Option TPS35xxxxB
0.8
1
1.2
ms
Orderable Option TPS35xxxxC
4
5
6
Orderable Option TPS35xxxxD
9
10
11
Orderable Option TPS35xxxxE
18
20
22
Orderable Option TPS35xxxxF
45
50
55
Orderable Option TPS35xxxxG
90
100
110
Orderable Option TPS35xxxxH
180
200
220
Orderable Option TPS35xxxxI
0.9
1
1.1
s
Orderable Option TPS35xxxxJ
1.26
1.4
1.54
Orderable Option TPS35xxxxK
1.44
1.6
1.76
Orderable Option TPS35xxxxL
9
10
11
Orderable Option TPS35xxxxM
45
50
55
Orderable Option TPS35xxxxN
90
100
110
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
PARAMETERTEST CONDITIONSMINTYPMAXUNIT
tGI_VIT–
Glitch immunity VIT–
5% VIT– overdrive#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER2
15
µs
t
MR_PW
MR pin pulse duration to assert reset
100
ns
tP-WD
WDI pulse duration to start next frame #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
500
ns
tHD-WDEN
WD-EN hold time to enable or disable WD operation #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
200
µs
tHD-SETx
SETx hold time to change WD timer setting #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
150
µs
tWD
Watchdog timeout period
Orderable Option TPS35xxxxB
0.8
1
1.2
ms
Orderable Option TPS35xxxxC
4
5
6
Orderable Option TPS35xxxxD
9
10
11
Orderable Option TPS35xxxxE
18
20
22
Orderable Option TPS35xxxxF
45
50
55
Orderable Option TPS35xxxxG
90
100
110
Orderable Option TPS35xxxxH
180
200
220
Orderable Option TPS35xxxxI
0.9
1
1.1
s
Orderable Option TPS35xxxxJ
1.26
1.4
1.54
Orderable Option TPS35xxxxK
1.44
1.6
1.76
Orderable Option TPS35xxxxL
9
10
11
Orderable Option TPS35xxxxM
45
50
55
Orderable Option TPS35xxxxN
90
100
110
tGI_VIT–
Glitch immunity VIT–
5% VIT– overdrive#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER2
15
µs
tGI_VIT–
GI_VIT– Glitch immunity VIT–
IT–
5% VIT– overdrive#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER2
IT–#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER215µs
t
MR_PW
MR pin pulse duration to assert reset
100
ns
t
MR_PW
MR_PWMR
MR pin pulse duration to assert resetMR100ns
tP-WD
WDI pulse duration to start next frame #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
500
ns
tP-WD
P-WDWDI pulse duration to start next frame #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDVVDD > VIT–
DDIT–500ns
tHD-WDEN
WD-EN hold time to enable or disable WD operation #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
200
µs
tHD-WDEN
HD-WDENWD-EN hold time to enable or disable WD operation #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDVVDD > VIT–
DDIT–200µs
tHD-SETx
SETx hold time to change WD timer setting #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
VDD > VIT–
150
µs
tHD-SETx
HD-SETxSETx hold time to change WD timer setting #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDV
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244052/SFXKDP01NFDVVDD > VIT–
DDIT–150µs
tWD
Watchdog timeout period
Orderable Option TPS35xxxxB
0.8
1
1.2
ms
tWD
WDWatchdog timeout periodOrderable Option TPS35xxxxB0.811.2ms
Orderable Option TPS35xxxxC
4
5
6
Orderable Option TPS35xxxxC456
Orderable Option TPS35xxxxD
9
10
11
Orderable Option TPS35xxxxD91011
Orderable Option TPS35xxxxE
18
20
22
Orderable Option TPS35xxxxE182022
Orderable Option TPS35xxxxF
45
50
55
Orderable Option TPS35xxxxF455055
Orderable Option TPS35xxxxG
90
100
110
Orderable Option TPS35xxxxG90100110
Orderable Option TPS35xxxxH
180
200
220
Orderable Option TPS35xxxxH180200220
Orderable Option TPS35xxxxI
0.9
1
1.1
s
Orderable Option TPS35xxxxI0.911.1s
Orderable Option TPS35xxxxJ
1.26
1.4
1.54
Orderable Option TPS35xxxxJ1.261.41.54
Orderable Option TPS35xxxxK
1.44
1.6
1.76
Orderable Option TPS35xxxxK1.441.61.76
Orderable Option TPS35xxxxL
9
10
11
Orderable Option TPS35xxxxL91011
Orderable Option TPS35xxxxM
45
50
55
Orderable Option TPS35xxxxM455055
Orderable Option TPS35xxxxN
90
100
110
Orderable Option TPS35xxxxN90100110
Overdrive % = [(VDD/ VIT–) – 1] × 100%
Not production tested
Overdrive % = [(VDD/ VIT–) – 1] × 100%DDIT–Not production tested
Switching Characteristics
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output RESET / WDO load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tSTRT
Startup delay#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER1_SF1
500
µs
tP_HL
RESET detect delay for VDD falling below VIT–
VDD : (VIT+ + 10%) to (VIT– – 10%)#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER4_SF1
30
50
µs
tSD
Watchdog startup delay
Orderable part number TPS35xA, TPS35xG
0
ms
Orderable part number TPS35xB, TPS35xH
180
200
220
Orderable part number TPS35xC, TPS35xI
450
500
550
Orderable part number TPS35xD, TPS35xJ
0.9
1
1.1
s
Orderable part number TPS35xE, TPS35xK
4.5
5
5.5
Orderable part number TPS35xF, TPS35xL
9
10
11
tD
Reset time delay #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER3_SF1
Orderable part number TPS35xxxxxxB
1.6
2
2.4
ms
Orderable part number TPS35xxxxxxC
9
10
11
ms
Orderable part number TPS35xxxxxxD
22.5
25
27.5
ms
Orderable part number TPS35xxxxxxE
45
50
55
ms
Orderable part number TPS35xxxxxxF
90
100
110
ms
Orderable part number TPS35xxxxxxG
180
200
220
ms
Orderable part number TPS35xxxxxxH
0.9
1
1.1
s
Orderable part number TPS35xxxxxxI
9
10
11
s
tWDO
Watchdog timeout delay
tD
s
t
MR_RES
Propagation delay from MR low to reset assertion
VDD ≥ VIT– + 0.2 V,
MR = V
MR_H to V
MR_L
100
ns
t
MR_tD
Delay from MR release to reset deassert
VDD = 3.3 V,
MR = V
MR_L to V
MR_H
tD
s
tP_HL measured from threshold trip point (VIT–) to RESET assert. VIT+ = VIT– + VHYS
Specified by design parameter. When VDD starts from less than the specified minimum VDD and then exceeds VIT+, reset is deasserted after the startup delay (tSTRT) + tD delay.
VDD voltage transitions from (VIT– - 10%) to (VIT– + 10%)
Switching Characteristics
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output RESET / WDO load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tSTRT
Startup delay#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER1_SF1
500
µs
tP_HL
RESET detect delay for VDD falling below VIT–
VDD : (VIT+ + 10%) to (VIT– – 10%)#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER4_SF1
30
50
µs
tSD
Watchdog startup delay
Orderable part number TPS35xA, TPS35xG
0
ms
Orderable part number TPS35xB, TPS35xH
180
200
220
Orderable part number TPS35xC, TPS35xI
450
500
550
Orderable part number TPS35xD, TPS35xJ
0.9
1
1.1
s
Orderable part number TPS35xE, TPS35xK
4.5
5
5.5
Orderable part number TPS35xF, TPS35xL
9
10
11
tD
Reset time delay #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER3_SF1
Orderable part number TPS35xxxxxxB
1.6
2
2.4
ms
Orderable part number TPS35xxxxxxC
9
10
11
ms
Orderable part number TPS35xxxxxxD
22.5
25
27.5
ms
Orderable part number TPS35xxxxxxE
45
50
55
ms
Orderable part number TPS35xxxxxxF
90
100
110
ms
Orderable part number TPS35xxxxxxG
180
200
220
ms
Orderable part number TPS35xxxxxxH
0.9
1
1.1
s
Orderable part number TPS35xxxxxxI
9
10
11
s
tWDO
Watchdog timeout delay
tD
s
t
MR_RES
Propagation delay from MR low to reset assertion
VDD ≥ VIT– + 0.2 V,
MR = V
MR_H to V
MR_L
100
ns
t
MR_tD
Delay from MR release to reset deassert
VDD = 3.3 V,
MR = V
MR_L to V
MR_H
tD
s
tP_HL measured from threshold trip point (VIT–) to RESET assert. VIT+ = VIT– + VHYS
Specified by design parameter. When VDD starts from less than the specified minimum VDD and then exceeds VIT+, reset is deasserted after the startup delay (tSTRT) + tD delay.
VDD voltage transitions from (VIT– - 10%) to (VIT– + 10%)
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output RESET / WDO load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tSTRT
Startup delay#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER1_SF1
500
µs
tP_HL
RESET detect delay for VDD falling below VIT–
VDD : (VIT+ + 10%) to (VIT– – 10%)#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER4_SF1
30
50
µs
tSD
Watchdog startup delay
Orderable part number TPS35xA, TPS35xG
0
ms
Orderable part number TPS35xB, TPS35xH
180
200
220
Orderable part number TPS35xC, TPS35xI
450
500
550
Orderable part number TPS35xD, TPS35xJ
0.9
1
1.1
s
Orderable part number TPS35xE, TPS35xK
4.5
5
5.5
Orderable part number TPS35xF, TPS35xL
9
10
11
tD
Reset time delay #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER3_SF1
Orderable part number TPS35xxxxxxB
1.6
2
2.4
ms
Orderable part number TPS35xxxxxxC
9
10
11
ms
Orderable part number TPS35xxxxxxD
22.5
25
27.5
ms
Orderable part number TPS35xxxxxxE
45
50
55
ms
Orderable part number TPS35xxxxxxF
90
100
110
ms
Orderable part number TPS35xxxxxxG
180
200
220
ms
Orderable part number TPS35xxxxxxH
0.9
1
1.1
s
Orderable part number TPS35xxxxxxI
9
10
11
s
tWDO
Watchdog timeout delay
tD
s
t
MR_RES
Propagation delay from MR low to reset assertion
VDD ≥ VIT– + 0.2 V,
MR = V
MR_H to V
MR_L
100
ns
t
MR_tD
Delay from MR release to reset deassert
VDD = 3.3 V,
MR = V
MR_L to V
MR_H
tD
s
At 1.04 V ≤ VDD ≤ 6 V, MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, WDO pull-up resistor (Rpull-up) = 100 kΩ to VDD, output RESET / WDO load (CLOAD) = 10 pF and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 1 V/µs. Typical values are at TA = 25℃DDMR RESETpull-upWDOpull-upLOADA
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tSTRT
Startup delay#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER1_SF1
500
µs
tP_HL
RESET detect delay for VDD falling below VIT–
VDD : (VIT+ + 10%) to (VIT– – 10%)#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER4_SF1
30
50
µs
tSD
Watchdog startup delay
Orderable part number TPS35xA, TPS35xG
0
ms
Orderable part number TPS35xB, TPS35xH
180
200
220
Orderable part number TPS35xC, TPS35xI
450
500
550
Orderable part number TPS35xD, TPS35xJ
0.9
1
1.1
s
Orderable part number TPS35xE, TPS35xK
4.5
5
5.5
Orderable part number TPS35xF, TPS35xL
9
10
11
tD
Reset time delay #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER3_SF1
Orderable part number TPS35xxxxxxB
1.6
2
2.4
ms
Orderable part number TPS35xxxxxxC
9
10
11
ms
Orderable part number TPS35xxxxxxD
22.5
25
27.5
ms
Orderable part number TPS35xxxxxxE
45
50
55
ms
Orderable part number TPS35xxxxxxF
90
100
110
ms
Orderable part number TPS35xxxxxxG
180
200
220
ms
Orderable part number TPS35xxxxxxH
0.9
1
1.1
s
Orderable part number TPS35xxxxxxI
9
10
11
s
tWDO
Watchdog timeout delay
tD
s
t
MR_RES
Propagation delay from MR low to reset assertion
VDD ≥ VIT– + 0.2 V,
MR = V
MR_H to V
MR_L
100
ns
t
MR_tD
Delay from MR release to reset deassert
VDD = 3.3 V,
MR = V
MR_L to V
MR_H
tD
s
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
PARAMETERTEST CONDITIONSMINTYPMAXUNIT
tSTRT
Startup delay#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER1_SF1
500
µs
tP_HL
RESET detect delay for VDD falling below VIT–
VDD : (VIT+ + 10%) to (VIT– – 10%)#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER4_SF1
30
50
µs
tSD
Watchdog startup delay
Orderable part number TPS35xA, TPS35xG
0
ms
Orderable part number TPS35xB, TPS35xH
180
200
220
Orderable part number TPS35xC, TPS35xI
450
500
550
Orderable part number TPS35xD, TPS35xJ
0.9
1
1.1
s
Orderable part number TPS35xE, TPS35xK
4.5
5
5.5
Orderable part number TPS35xF, TPS35xL
9
10
11
tD
Reset time delay #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER3_SF1
Orderable part number TPS35xxxxxxB
1.6
2
2.4
ms
Orderable part number TPS35xxxxxxC
9
10
11
ms
Orderable part number TPS35xxxxxxD
22.5
25
27.5
ms
Orderable part number TPS35xxxxxxE
45
50
55
ms
Orderable part number TPS35xxxxxxF
90
100
110
ms
Orderable part number TPS35xxxxxxG
180
200
220
ms
Orderable part number TPS35xxxxxxH
0.9
1
1.1
s
Orderable part number TPS35xxxxxxI
9
10
11
s
tWDO
Watchdog timeout delay
tD
s
t
MR_RES
Propagation delay from MR low to reset assertion
VDD ≥ VIT– + 0.2 V,
MR = V
MR_H to V
MR_L
100
ns
t
MR_tD
Delay from MR release to reset deassert
VDD = 3.3 V,
MR = V
MR_L to V
MR_H
tD
s
tSTRT
Startup delay#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER1_SF1
500
µs
tSTRT
STRTStartup delay#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER1_SF1
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER1_SF1
500µs
tP_HL
RESET detect delay for VDD falling below VIT–
VDD : (VIT+ + 10%) to (VIT– – 10%)#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER4_SF1
30
50
µs
tP_HL
P_HLRESET detect delay for VDD falling below VIT–
IT–VDD : (VIT+ + 10%) to (VIT– – 10%)#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER4_SF1
DD IT+ IT–#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER4_SF13050µs
tSD
Watchdog startup delay
Orderable part number TPS35xA, TPS35xG
0
ms
tSD
SDWatchdog startup delayOrderable part number TPS35xA, TPS35xG0ms
Orderable part number TPS35xB, TPS35xH
180
200
220
Orderable part number TPS35xB, TPS35xH180200220
Orderable part number TPS35xC, TPS35xI
450
500
550
Orderable part number TPS35xC, TPS35xI450500550
Orderable part number TPS35xD, TPS35xJ
0.9
1
1.1
s
Orderable part number TPS35xD, TPS35xJ0.911.1s
Orderable part number TPS35xE, TPS35xK
4.5
5
5.5
Orderable part number TPS35xE, TPS35xK4.555.5
Orderable part number TPS35xF, TPS35xL
9
10
11
Orderable part number TPS35xF, TPS35xL91011
tD
Reset time delay #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER3_SF1
Orderable part number TPS35xxxxxxB
1.6
2
2.4
ms
tD
DReset time delay #GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER3_SF1
#GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000244220/A_SUPERVISOR_VVCM_7_TIMINGREQ_FOOTER3_SF1Orderable part number TPS35xxxxxxB1.622.4ms
Orderable part number TPS35xxxxxxC
9
10
11
ms
Orderable part number TPS35xxxxxxC91011ms
Orderable part number TPS35xxxxxxD
22.5
25
27.5
ms
Orderable part number TPS35xxxxxxD22.52527.5ms
Orderable part number TPS35xxxxxxE
45
50
55
ms
Orderable part number TPS35xxxxxxE455055ms
Orderable part number TPS35xxxxxxF
90
100
110
ms
Orderable part number TPS35xxxxxxF90100110ms
Orderable part number TPS35xxxxxxG
180
200
220
ms
Orderable part number TPS35xxxxxxG180200220ms
Orderable part number TPS35xxxxxxH
0.9
1
1.1
s
Orderable part number TPS35xxxxxxH0.911.1s
Orderable part number TPS35xxxxxxI
9
10
11
s
Orderable part number TPS35xxxxxxI91011s
tWDO
Watchdog timeout delay
tD
s
tWDO
WDOWatchdog timeout delaytD
Ds
t
MR_RES
Propagation delay from MR low to reset assertion
VDD ≥ VIT– + 0.2 V,
MR = V
MR_H to V
MR_L
100
ns
t
MR_RES
MR_RESMRPropagation delay from MR low to reset assertionMRVDD ≥ VIT– + 0.2 V,
MR = V
MR_H to V
MR_L
DDIT–MR
MR_H MR
MR_LMR100ns
t
MR_tD
Delay from MR release to reset deassert
VDD = 3.3 V,
MR = V
MR_L to V
MR_H
tD
s
t
MR_tD
MR_tDMRDelay from MR release to reset deassertMR VDD = 3.3 V,
MR = V
MR_L to V
MR_H
DDMR
MR_L MR
MR_H MRtD
Ds
tP_HL measured from threshold trip point (VIT–) to RESET assert. VIT+ = VIT– + VHYS
Specified by design parameter. When VDD starts from less than the specified minimum VDD and then exceeds VIT+, reset is deasserted after the startup delay (tSTRT) + tD delay.
VDD voltage transitions from (VIT– - 10%) to (VIT– + 10%)
tP_HL measured from threshold trip point (VIT–) to RESET assert. VIT+ = VIT– + VHYS
P_HLIT–IT+IT–HYSSpecified by design parameter. When VDD starts from less than the specified minimum VDD and then exceeds VIT+, reset is deasserted after the startup delay (tSTRT) + tD delay.DDIT+STRTDVDD voltage transitions from (VIT– - 10%) to (VIT– + 10%)IT– IT–
Timing Diagrams
*
Added a footnote to for tINIT
no
Functional Timing Diagram
Timing Diagrams
*
Added a footnote to for tINIT
no
*
Added a footnote to for tINIT
no
*
Added a footnote to for tINIT
no
*Added a footnote to for tINIT
INITno
Functional Timing Diagram
Functional Timing Diagram
Functional Timing Diagram
Functional Timing Diagram
Typical Characteristics
all curves are taken at TA = 25°C
(unless otherwise noted)
VIT- Accuracy vs Temperature
VIT- Accuracy
Histogram
VIT- Hysteresis Vs Temperature
Supply Glitch Immunity vs Overdrive
Timer Accuracy vs
Temperature
Timer Accuracy Histogram
tWD vs Capacitance
tD vs Capacitance
RESET VOL vs I
sink, VDD = 1.5 V
WDO VOL vs I
sink, VDD = 1.5 V
RESET VOL vs I sink, VDD = 3.3 V
WDO VOL vs I sink, VDD = 3.3 V
RESET VOH vs I source, VDD = 2.0 V
WDO VOH vs I source, VDD = 2.0 V
RESET VOH vs I source, VDD = 6.0 V
WDO VOH vs I source, VDD = 6.0 V
Supply Current
vs Power-Supply Voltage
Typical Characteristics
all curves are taken at TA = 25°C
(unless otherwise noted)
VIT- Accuracy vs Temperature
VIT- Accuracy
Histogram
VIT- Hysteresis Vs Temperature
Supply Glitch Immunity vs Overdrive
Timer Accuracy vs
Temperature
Timer Accuracy Histogram
tWD vs Capacitance
tD vs Capacitance
RESET VOL vs I
sink, VDD = 1.5 V
WDO VOL vs I
sink, VDD = 1.5 V
RESET VOL vs I sink, VDD = 3.3 V
WDO VOL vs I sink, VDD = 3.3 V
RESET VOH vs I source, VDD = 2.0 V
WDO VOH vs I source, VDD = 2.0 V
RESET VOH vs I source, VDD = 6.0 V
WDO VOH vs I source, VDD = 6.0 V
Supply Current
vs Power-Supply Voltage
all curves are taken at TA = 25°C
(unless otherwise noted)
VIT- Accuracy vs Temperature
VIT- Accuracy
Histogram
VIT- Hysteresis Vs Temperature
Supply Glitch Immunity vs Overdrive
Timer Accuracy vs
Temperature
Timer Accuracy Histogram
tWD vs Capacitance
tD vs Capacitance
RESET VOL vs I
sink, VDD = 1.5 V
WDO VOL vs I
sink, VDD = 1.5 V
RESET VOL vs I sink, VDD = 3.3 V
WDO VOL vs I sink, VDD = 3.3 V
RESET VOH vs I source, VDD = 2.0 V
WDO VOH vs I source, VDD = 2.0 V
RESET VOH vs I source, VDD = 6.0 V
WDO VOH vs I source, VDD = 6.0 V
Supply Current
vs Power-Supply Voltage
all curves are taken at TA = 25°C
(unless otherwise noted)A
VIT- Accuracy vs Temperature
VIT- Accuracy
Histogram
VIT- Hysteresis Vs Temperature
Supply Glitch Immunity vs Overdrive
Timer Accuracy vs
Temperature
Timer Accuracy Histogram
tWD vs Capacitance
tD vs Capacitance
RESET VOL vs I
sink, VDD = 1.5 V
WDO VOL vs I
sink, VDD = 1.5 V
RESET VOL vs I sink, VDD = 3.3 V
WDO VOL vs I sink, VDD = 3.3 V
RESET VOH vs I source, VDD = 2.0 V
WDO VOH vs I source, VDD = 2.0 V
RESET VOH vs I source, VDD = 6.0 V
WDO VOH vs I source, VDD = 6.0 V
Supply Current
vs Power-Supply Voltage
VIT- Accuracy vs Temperature
VIT- Accuracy vs TemperatureIT-
VIT- Accuracy
Histogram
VIT- Accuracy
HistogramIT-
VIT- Hysteresis Vs Temperature
VIT- Hysteresis Vs TemperatureIT-
Supply Glitch Immunity vs Overdrive
Supply Glitch Immunity vs Overdrive
Timer Accuracy vs
Temperature
Timer Accuracy vs
Temperature
Timer Accuracy Histogram
Timer Accuracy Histogram
tWD vs Capacitance
tWD vs CapacitanceWD
tD vs Capacitance
tD vs CapacitanceD
RESET VOL vs I
sink, VDD = 1.5 V
RESET VOL vs I
sink, VDD = 1.5 VOLsinkDD
WDO VOL vs I
sink, VDD = 1.5 V
WDO VOL vs I
sink, VDD = 1.5 VOLsinkDD
RESET VOL vs I sink, VDD = 3.3 V
RESET VOL vs I sink, VDD = 3.3 VOLsinkDD
WDO VOL vs I sink, VDD = 3.3 V
WDO VOL vs I sink, VDD = 3.3 VOLsinkDD
RESET VOH vs I source, VDD = 2.0 V
RESET VOH vs I source, VDD = 2.0 VOHsourceDD
WDO VOH vs I source, VDD = 2.0 V
WDO VOH vs I source, VDD = 2.0 VOHsourceDD
RESET VOH vs I source, VDD = 6.0 V
RESET VOH vs I source, VDD = 6.0 VOHsourceDD
WDO VOH vs I source, VDD = 6.0 V
WDO VOH vs I source, VDD = 6.0 VOHsourceDD
Supply Current
vs Power-Supply Voltage
Supply Current
vs Power-Supply Voltage
Detailed Description
Overview
The TPS35 is a high-accuracy
under voltage supervisor with an integrated
timeout watchdog timer device. The device
family supports multiple features related to watchdog operation in a compact 6 pin WSON and 8 pin SOT23 package. The devices are
available in 6 different
pinout configurations. Each pinout offers access to different features to meet the various
application requirements.
Functional Block Diagrams
Pinout Option A
Pinout Option B
Pinout Option C
Pinout Option D
Pinout Option J
Pinout Option K
Feature Description
Voltage Supervisor
The TPS35 offers high accuracy
under voltage supervisor function at very low quiescent current. The voltage
supervisor function is always active. After the device powers up from VDD <
VPOR, the RESET and WDO outputs are actively driven when VDD is
greater than VPOR. The device starts monitoring the supply level when the
VDD voltage is greater than 1.04 V. The device holds the RESET pin asserted for
tSTRT + tD time after the VDD > VIT+
(VIT- + VHYS). Refer
for the
tD value computation. For a capacitor based tD delay
option, the RESET is asserted for tSTRT + 2 msec time if the CRST pin is
open.
Device pinout options A to C and J, K offer only RESET output. In these devices the internal RESET output from supervisor and WDO output from watchdog timer are ANDed together to drive the external RESET output.
The supervisor offers wide range of fixed
monitoring thresholds (VIT-) from 1.05 V to 5.40 V in steps of 50 mV. The
device asserts the RESET output when the VDD signal falls below VIT-
threshold. The device offers hysteresis functionality for voltage supervision. This
makes sure the supply has recovered above the monitoring threshold before the RESET
output is deasserted. The TPS35 typical voltage hysteresis
(VHYS) is 5%. Along with the voltage hysteresis, the device keeps the
RESET output asserted for time duration tD after the supply has risen
above VIT+. The RESET output assert duration changes from tD
to tSTRT + tD if the VDD signal is ramping from voltage <
VPOR. The tD time duration can be programmable using an
external capacitor or fixed time options offered by the device.
The typical timing behavior for a voltage
supervisor and the RESET output is showcased in . The voltage
supervisor monitoring output has higher priority over watchdog functionality. If the
device voltage supervisor output is asserted, the watchdog functionality is disabled
including WDO assert control. The device resumes watchdog related functionality only
after the supply is stable and the tD time duration has elapsed.
Voltage Supervisor Timing Diagram
Timeout Watchdog Timer
The TPS35 offers high
precision timeout watchdog timer monitoring. The device is available in multiple
pinout options A to K which support multiple features to meet
ever expanding needs of various applications. Make sure a correct pinout is selected
to meet the application needs.
The timeout watchdog is
active when the VDD voltage is higher than the VIT- + VHYS
and the RESET is deasserted after the tD time. The watchdog stays
active as long as VDD > VIT- and watchdog is enabled.
TPS35 family offers various startup time delay options to make
sure enough time is available for the host to complete boot operation. Please refer
for
additional details.
The timeout watchdog timer monitors the WDI pin for falling edge in the time frame defined by tWD time period. Refer
section to arrive at the relevant tWD value needed for application. The timer value is reset when a valid falling edge is detected on WDI pin in the tWD time duration. When a valid WDI transition is not detected in tWD time, the device asserts RESET output for pinout options A, B, C, J and K or WDO output for pinout D. The RESET or WDO is asserted for time tD
. Refer
to arrive at the relevant tD
value needed for application.
shows the basic operation for timeout watchdog timer operation. The TPS35 watchdog functionality supports multiple features. Details are available in following sub sections.
Timeout Watchdog Timer Operation
tWD Timer
The tWD timer for TPS35 can be set using an external capacitor connected between CWD pin and GND pin. This feature is available with pinout options A or B or K. Applications which are space constrained or need timer values which meet offered timer options, can benefit when using pinout options C or D
or J. The TPS35 offers multiple fixed timer options ranging from 1 msec up-to 100 sec.
The TPS35, when using capacitance based timer, senses the capacitance value during the power up or after a RESET event. The capacitor is charged and discharged with known internal current source for one cycle to sense the capacitance value. The sensed value is used to arrive at tWD timer for the watchdog operation. This unique implementation helps reduce the continuous charge and discharge current for the capacitor, thus reducing overall current consumption. Continuous charge and discharge of capacitance creates wider dead time (no watchdog monitor functionality) when capacitor is discharging. The dead time is higher for high value of capacitance. The unique implementation of TPS35 helps avoid the dead time as the capacitance is not continuously charging or discharging under normal operation. Make sure CCWD is < 200 x CCRST for accurate calibration of capacitance. #GUID-126A0EA8-DA64-4C35-A2AC-DECE33E8FC5E/EQUATION-BLOCK_XV1_5Z1_YTB highlights the relationship between tWD in second and CWD capacitance in farad. The tWD timer is 20% accurate for an ideal capacitor. Accuracy of the capacitance will have additional impact on the tWD time. Make sure the capacitance meets the recommended operating range. Capacitance outside the recommended range can lead to incorrect operation of the device.
tWD (sec) = 4.95 x 106 x CCWD (F)
The TPS35 also offers wide selection of high accuracy fixed timer options starting from 1 msec to 100 sec including various industry standard values. The TPS35 fixed time options are ±10% accurate for tWD ≥ 10 msec. For tWD < 10 msec, the accuracy is ±20%. tWD value relevant to application can be identified from the orderable part number. Refer
section to identify mapping of orderable part number to tWD value.
The TPS35 offers flexibility to change the tWD value on the fly by controlling the logic levels on the SETx pins.
section explains the advantages offered by this feature and the device behavior with various SETx pin combinations.
Watchdog Enable Disable Operation
The TPS35 supports
watchdog enable or disable functionality. This functionality is critical for
different use cases as listed below.
Disable watchdog during firmware update to avoid host RESET.
Disable watchdog during software step-by-step debug operation.
Disable watchdog when performing critical task to avoid watchdog error
interrupt.
Keep watchdog disabled until host boots up.
The TPS35 supports
watchdog enable or disable functionality through either WD-EN pin (pin configuration
C) or SET[1:0] = 0b'01 (pin
configuration B) logic combination. For a given pinout
only one of these two methods is available for the user to disable watchdog
operation.
For a pinout which offers a WD-EN pin,
the watchdog enable disable functionality is controlled by the logic state of WD-EN
pin. Drive WD-EN = 1 to enable the watchdog operation or drive WD-EN = 0 to disable
the watchdog operation. The WD-EN pin can be toggled any time during the device
operation. The diagram
shows timing behavior with WD-EN pin control.
Watchdog Enable: WD-EN Pin
Control
SET[1:0] = 0b'01 combination can be
used to disable watchdog operation with a pinout which offers SET1 and SET0 pins,
but does not include WD-EN pin. The SET pin logic states can be changed at any time
during watchdog operation. Refer
section for additional details regarding SET[1:0] pin behavior.
Pinout options A, B, K offer watchdog timer control using a
capacitance connected between CWD and GND pin. A capacitance value higher than
recommended or connect to GND leads to watchdog functionality getting disabled.
Capacitance based disable operation overrides the other two options mentioned above.
Changing capacitance on the fly does not enable or disable watchdog operation. A
power supply recycle or device recovery after UV fault,
MR low event is needed
to detect change in capacitance.
Ongoing watchdog frame is terminated
when watchdog is disabled. WDO stays deasserted when watchdog operation is disabled.
For a pinout with only RESET output, the RESET can assert if supply supervisor
error occurs. When
enabled the device immediately enters tWD
frame and start watchdog
monitoring operation.
tSD Watchdog Start Up Delay
The TPS35 supports watchdog
startup delay feature. This feature is activated after power up or after a RESET assert event or after WDO
assert event. When tSD frame is active, the device monitors the WDI pin
but the WDO output is not asserted. This feature allows time for the host complete
boot process before watchdog monitoring can take over. The start up delay helps
avoid unexpected WDO
or RESET assert events
during boot. The tSD time is predetermined based on the device part
number selected. Refer
section
for details to map the part number to tSD time. Pinout option A, B, K are available only in no delay or 10 sec
start up delay options.
The tSD frame is complete when the time
duration selected for tSD is over or host provides a valid transition on
the WDI pin. The host must provide a valid transition on the WDI pin during
tSD time. The device exits the tSD frame and enters
watchdog monitoring phase after valid WDI transition. Failure to provide valid
transition on WDI pin triggers the watchdog error by asserting the WDO output
pin. For devices with only RESET output, the RESET pin
is asserted.
The tSD frame is not initiated when the
watchdog functionality is enabled using WD-EN pin or SET[1:0] pin combination as described in
section.
shows the
operation for tSD time frame.
tSD Frame
Behavior
SET Pin Behavior
The TPS35 offers one or two SET pins based on the pinout option selected. SET pins offer flexibility to the user to program the tWD timer on the fly to meet various application requirements. Typical use cases where SET pin can be used are:
Use wide timeout timer when host is in sleep mode, change to small timeout operation when host is operational. Watchdog can be used to wake up the host after long duration to perform the application related activities before going back to sleep.
Change to wide timeout timer when performing system critical tasks to make sure the watchdog does not interrupt the critical task. Change timer to application specified interval after the critical task is complete.
The tWD timer value for the device is combination of timer selection based on the CWD pin or fixed timer value along with SET pin logic level. The base tWD timer value is decided based on the Watchdog Time selector in the
section. The SET pin logic level is decoded during the device power up. The SET pin value can be changed any time during the operation. SETx pin change which leads to change of watchdog timer value or enable disable state, terminates the ongoing watchdog frame immediately. SETx pins can be updated when WDO or RESET output is asserted as well. The updated tWD timer value will be applied after output is deasserted and the tSD timer is over or terminated.
For a pinout which offers only SET0 pin to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. showcases an example of the tWD values for different SET0 logic levels when using Watchdog Time setting as option D = 10 msec.
tWD Scaling with SET0 Pin Only (Pin
Configuration A, J)
WATCHDOG TIME SCALING SELECTION
tWD
SET0 = 0
SET0 = 1
A
10 msec
20 msec
B
10 msec
40 msec
C
10 msec
80 msec
D
10 msec
160 msec
E
10 msec
320 msec
F
10 msec
640 msec
G
10 msec
1280 msec
For pinouts which offer both SET0 & SET1 pins to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. Two SETx pins offer 3 different time scaling options. The SET[1:0] = 0b'01 combination disables the watchdog operation. showcases an example of the tWD values for different SET[1:0] logic levels when using Watchdog Time setting as option G = 100 msec. The package pin out selected does not offer WD-EN pin.
tWD Scaling with SET0 & SET1
Pins, WD-EN Pin Not Available (Pin Configuration B)
WATCHDOG TIME SCALING SELECTION
tWD
SET[1:0] = 0b'00
SET[1:0] = 0b'01
SET[1:0] = 0b'10
SET[1:0] = 0b'11
A
100 msec
Watchdog disable
200 msec
400 msec
B
100 msec
Watchdog disable
400 msec
800 msec
C
100 msec
Watchdog disable
800 msec
1600 msec
D
100 msec
Watchdog disable
1600 msec
3200 msec
E
100 msec
Watchdog disable
3200 msec
6400 msec
F
100 msec
Watchdog disable
6400 msec
12800 msec
G
100 msec
Watchdog disable
12800 msec
25600 msec
Selected pinout option can offer WD-EN pin along
with SET[1:0] pins (Pin Configuration C, D). With this pinout, the WD-EN pin
controls watchdog enable and disable operation. The SET[1:0] = 0b'01 combination
operates as SET[1:0] = 0b'00.
Make sure the tWD value with SETx multiplier does not exceed 640 sec. If a selection of timer and multiplier results in tWD > 640 sec, the timer value will be restricted to 640 sec.
to diagrams show the timing behavior with respect to SETx status changes.
Watchdog Behavior with SETx Pin Status
Watchdog Operation with 2 SET Pins
Watchdog Operation with 1 SET Pin
Manual RESET
The TPS35 supports
manual reset functionality using MR pin.
MR pin when driven with voltage lower than 0.3 x VDD,
asserts the RESET output. The MR pin has 100 kΩ pull up to VDD. The
MR pin can be left floating. The internal pull up makes
sure the output is not asserted due to MR pin trigger.
The output is deasserted after
MR pin voltage rises above 0.7 x VDD voltage and time tD is elapsed. Refer for more
details.
MR Pin
Response
RESET and WDO Output
The TPS35 device can offer RESET or
RESET with independent WDO output pin. The output configuration is dependent on the
pinout variant selected. For a pinout which has only RESET output, the RESET output
is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold or watchdog timer
error is detected. For a pinout which has independent RESET and WDO output pins, the
RESET output is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold. WDO output is
asserted only when watchdog timer error is detected. RESET error has higher priority
than WDO error. If RESET is asserted when WDO is asserted, the device deasserts the
WDO pin and watchdog is disabled until RESET pin is deasserted and startup delay
frame is terminated.
The output will be asserted for tD
time when any relevant events
described above are detected. The time tD
can be programmed by
connecting a capacitor between CRST pin and GND or device will assert tD
for fixed time duration as
selected by orderable part number. Refer
section for all
available options.
describes the relationship between capacitor value and the time tD
. Make sure the capacitance meets
the recommended operating range. Capacitance outside the recommended range can lead
to incorrect operation of the device.
t
D
(sec) = 4.95 x
106 x CCRST (F)
TPS35 also offers
a unique option of latched output. An orderable with latched output will hold the
output in asserted state indefinitely until the device is power cycled or the error
condition is addressed. If the output is latched due to voltage
supervisor undervoltage detection, the output latch will be released when VDD
voltage rises above the VIT- + VHYS level. If the output is latched
due to MR pin low voltage, the output latch will be released
when MR pin voltage rises above 0.7 x VDD level. If
the output is latched due to watchdog timer error, the output latch will be released
when a WDI negative edge is detected or the device is shutdown and powered up again.
shows
timing behavior of the device with latched output configuration.
Output Latch Timing Behavior
Device Functional Modes
#GUID-B008A25A-278A-4B38-AFBB-A738DE66DE26/TABLE_TV3_FWV_HVB
summarizes the functional modes of the TPS35.
Device Functional
Modes
VDD
WATCHDOG STATUS
WDI
WDO
RESET
VDD <
VPOR
Not Applicable
—
Undefined
Undefined
VPOR ≤
VDD < VIT-
Not Applicable
Ignored
High
Low
VDD ≥ VIT+
Disabled
Ignored
High
High
Enabled
tpulse
1 < tWD(min)
High
High
Enabled
tpulse
1 > tWD(max)
Low
High
Where tpulse is the time between falling edges on
WDI.
Detailed Description
Overview
The TPS35 is a high-accuracy
under voltage supervisor with an integrated
timeout watchdog timer device. The device
family supports multiple features related to watchdog operation in a compact 6 pin WSON and 8 pin SOT23 package. The devices are
available in 6 different
pinout configurations. Each pinout offers access to different features to meet the various
application requirements.
Overview
The TPS35 is a high-accuracy
under voltage supervisor with an integrated
timeout watchdog timer device. The device
family supports multiple features related to watchdog operation in a compact 6 pin WSON and 8 pin SOT23 package. The devices are
available in 6 different
pinout configurations. Each pinout offers access to different features to meet the various
application requirements.
The TPS35 is a high-accuracy
under voltage supervisor with an integrated
timeout watchdog timer device. The device
family supports multiple features related to watchdog operation in a compact 6 pin WSON and 8 pin SOT23 package. The devices are
available in 6 different
pinout configurations. Each pinout offers access to different features to meet the various
application requirements.
The TPS35 is a high-accuracy
under voltage supervisor with an integrated
timeout watchdog timer device. The device
family supports multiple features related to watchdog operation in a compact 6 pin WSON and 8 pin SOT23 package. The devices are
available in 6 different
pinout configurations. Each pinout offers access to different features to meet the various
application requirements. TPS35under voltage supervisor with an integrated timeout 6 pin WSON and 6
Functional Block Diagrams
Pinout Option A
Pinout Option B
Pinout Option C
Pinout Option D
Pinout Option J
Pinout Option K
Functional Block Diagrams
Pinout Option A
Pinout Option B
Pinout Option C
Pinout Option D
Pinout Option J
Pinout Option K
Pinout Option A
Pinout Option B
Pinout Option C
Pinout Option D
Pinout Option J
Pinout Option K
Pinout Option A
Pinout Option A
Pinout Option B
Pinout Option B
Pinout Option C
Pinout Option C
Pinout Option D
Pinout Option D
Pinout Option J
Pinout Option J
Pinout Option K
Pinout Option K
Feature Description
Voltage Supervisor
The TPS35 offers high accuracy
under voltage supervisor function at very low quiescent current. The voltage
supervisor function is always active. After the device powers up from VDD <
VPOR, the RESET and WDO outputs are actively driven when VDD is
greater than VPOR. The device starts monitoring the supply level when the
VDD voltage is greater than 1.04 V. The device holds the RESET pin asserted for
tSTRT + tD time after the VDD > VIT+
(VIT- + VHYS). Refer
for the
tD value computation. For a capacitor based tD delay
option, the RESET is asserted for tSTRT + 2 msec time if the CRST pin is
open.
Device pinout options A to C and J, K offer only RESET output. In these devices the internal RESET output from supervisor and WDO output from watchdog timer are ANDed together to drive the external RESET output.
The supervisor offers wide range of fixed
monitoring thresholds (VIT-) from 1.05 V to 5.40 V in steps of 50 mV. The
device asserts the RESET output when the VDD signal falls below VIT-
threshold. The device offers hysteresis functionality for voltage supervision. This
makes sure the supply has recovered above the monitoring threshold before the RESET
output is deasserted. The TPS35 typical voltage hysteresis
(VHYS) is 5%. Along with the voltage hysteresis, the device keeps the
RESET output asserted for time duration tD after the supply has risen
above VIT+. The RESET output assert duration changes from tD
to tSTRT + tD if the VDD signal is ramping from voltage <
VPOR. The tD time duration can be programmable using an
external capacitor or fixed time options offered by the device.
The typical timing behavior for a voltage
supervisor and the RESET output is showcased in . The voltage
supervisor monitoring output has higher priority over watchdog functionality. If the
device voltage supervisor output is asserted, the watchdog functionality is disabled
including WDO assert control. The device resumes watchdog related functionality only
after the supply is stable and the tD time duration has elapsed.
Voltage Supervisor Timing Diagram
Timeout Watchdog Timer
The TPS35 offers high
precision timeout watchdog timer monitoring. The device is available in multiple
pinout options A to K which support multiple features to meet
ever expanding needs of various applications. Make sure a correct pinout is selected
to meet the application needs.
The timeout watchdog is
active when the VDD voltage is higher than the VIT- + VHYS
and the RESET is deasserted after the tD time. The watchdog stays
active as long as VDD > VIT- and watchdog is enabled.
TPS35 family offers various startup time delay options to make
sure enough time is available for the host to complete boot operation. Please refer
for
additional details.
The timeout watchdog timer monitors the WDI pin for falling edge in the time frame defined by tWD time period. Refer
section to arrive at the relevant tWD value needed for application. The timer value is reset when a valid falling edge is detected on WDI pin in the tWD time duration. When a valid WDI transition is not detected in tWD time, the device asserts RESET output for pinout options A, B, C, J and K or WDO output for pinout D. The RESET or WDO is asserted for time tD
. Refer
to arrive at the relevant tD
value needed for application.
shows the basic operation for timeout watchdog timer operation. The TPS35 watchdog functionality supports multiple features. Details are available in following sub sections.
Timeout Watchdog Timer Operation
tWD Timer
The tWD timer for TPS35 can be set using an external capacitor connected between CWD pin and GND pin. This feature is available with pinout options A or B or K. Applications which are space constrained or need timer values which meet offered timer options, can benefit when using pinout options C or D
or J. The TPS35 offers multiple fixed timer options ranging from 1 msec up-to 100 sec.
The TPS35, when using capacitance based timer, senses the capacitance value during the power up or after a RESET event. The capacitor is charged and discharged with known internal current source for one cycle to sense the capacitance value. The sensed value is used to arrive at tWD timer for the watchdog operation. This unique implementation helps reduce the continuous charge and discharge current for the capacitor, thus reducing overall current consumption. Continuous charge and discharge of capacitance creates wider dead time (no watchdog monitor functionality) when capacitor is discharging. The dead time is higher for high value of capacitance. The unique implementation of TPS35 helps avoid the dead time as the capacitance is not continuously charging or discharging under normal operation. Make sure CCWD is < 200 x CCRST for accurate calibration of capacitance. #GUID-126A0EA8-DA64-4C35-A2AC-DECE33E8FC5E/EQUATION-BLOCK_XV1_5Z1_YTB highlights the relationship between tWD in second and CWD capacitance in farad. The tWD timer is 20% accurate for an ideal capacitor. Accuracy of the capacitance will have additional impact on the tWD time. Make sure the capacitance meets the recommended operating range. Capacitance outside the recommended range can lead to incorrect operation of the device.
tWD (sec) = 4.95 x 106 x CCWD (F)
The TPS35 also offers wide selection of high accuracy fixed timer options starting from 1 msec to 100 sec including various industry standard values. The TPS35 fixed time options are ±10% accurate for tWD ≥ 10 msec. For tWD < 10 msec, the accuracy is ±20%. tWD value relevant to application can be identified from the orderable part number. Refer
section to identify mapping of orderable part number to tWD value.
The TPS35 offers flexibility to change the tWD value on the fly by controlling the logic levels on the SETx pins.
section explains the advantages offered by this feature and the device behavior with various SETx pin combinations.
Watchdog Enable Disable Operation
The TPS35 supports
watchdog enable or disable functionality. This functionality is critical for
different use cases as listed below.
Disable watchdog during firmware update to avoid host RESET.
Disable watchdog during software step-by-step debug operation.
Disable watchdog when performing critical task to avoid watchdog error
interrupt.
Keep watchdog disabled until host boots up.
The TPS35 supports
watchdog enable or disable functionality through either WD-EN pin (pin configuration
C) or SET[1:0] = 0b'01 (pin
configuration B) logic combination. For a given pinout
only one of these two methods is available for the user to disable watchdog
operation.
For a pinout which offers a WD-EN pin,
the watchdog enable disable functionality is controlled by the logic state of WD-EN
pin. Drive WD-EN = 1 to enable the watchdog operation or drive WD-EN = 0 to disable
the watchdog operation. The WD-EN pin can be toggled any time during the device
operation. The diagram
shows timing behavior with WD-EN pin control.
Watchdog Enable: WD-EN Pin
Control
SET[1:0] = 0b'01 combination can be
used to disable watchdog operation with a pinout which offers SET1 and SET0 pins,
but does not include WD-EN pin. The SET pin logic states can be changed at any time
during watchdog operation. Refer
section for additional details regarding SET[1:0] pin behavior.
Pinout options A, B, K offer watchdog timer control using a
capacitance connected between CWD and GND pin. A capacitance value higher than
recommended or connect to GND leads to watchdog functionality getting disabled.
Capacitance based disable operation overrides the other two options mentioned above.
Changing capacitance on the fly does not enable or disable watchdog operation. A
power supply recycle or device recovery after UV fault,
MR low event is needed
to detect change in capacitance.
Ongoing watchdog frame is terminated
when watchdog is disabled. WDO stays deasserted when watchdog operation is disabled.
For a pinout with only RESET output, the RESET can assert if supply supervisor
error occurs. When
enabled the device immediately enters tWD
frame and start watchdog
monitoring operation.
tSD Watchdog Start Up Delay
The TPS35 supports watchdog
startup delay feature. This feature is activated after power up or after a RESET assert event or after WDO
assert event. When tSD frame is active, the device monitors the WDI pin
but the WDO output is not asserted. This feature allows time for the host complete
boot process before watchdog monitoring can take over. The start up delay helps
avoid unexpected WDO
or RESET assert events
during boot. The tSD time is predetermined based on the device part
number selected. Refer
section
for details to map the part number to tSD time. Pinout option A, B, K are available only in no delay or 10 sec
start up delay options.
The tSD frame is complete when the time
duration selected for tSD is over or host provides a valid transition on
the WDI pin. The host must provide a valid transition on the WDI pin during
tSD time. The device exits the tSD frame and enters
watchdog monitoring phase after valid WDI transition. Failure to provide valid
transition on WDI pin triggers the watchdog error by asserting the WDO output
pin. For devices with only RESET output, the RESET pin
is asserted.
The tSD frame is not initiated when the
watchdog functionality is enabled using WD-EN pin or SET[1:0] pin combination as described in
section.
shows the
operation for tSD time frame.
tSD Frame
Behavior
SET Pin Behavior
The TPS35 offers one or two SET pins based on the pinout option selected. SET pins offer flexibility to the user to program the tWD timer on the fly to meet various application requirements. Typical use cases where SET pin can be used are:
Use wide timeout timer when host is in sleep mode, change to small timeout operation when host is operational. Watchdog can be used to wake up the host after long duration to perform the application related activities before going back to sleep.
Change to wide timeout timer when performing system critical tasks to make sure the watchdog does not interrupt the critical task. Change timer to application specified interval after the critical task is complete.
The tWD timer value for the device is combination of timer selection based on the CWD pin or fixed timer value along with SET pin logic level. The base tWD timer value is decided based on the Watchdog Time selector in the
section. The SET pin logic level is decoded during the device power up. The SET pin value can be changed any time during the operation. SETx pin change which leads to change of watchdog timer value or enable disable state, terminates the ongoing watchdog frame immediately. SETx pins can be updated when WDO or RESET output is asserted as well. The updated tWD timer value will be applied after output is deasserted and the tSD timer is over or terminated.
For a pinout which offers only SET0 pin to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. showcases an example of the tWD values for different SET0 logic levels when using Watchdog Time setting as option D = 10 msec.
tWD Scaling with SET0 Pin Only (Pin
Configuration A, J)
WATCHDOG TIME SCALING SELECTION
tWD
SET0 = 0
SET0 = 1
A
10 msec
20 msec
B
10 msec
40 msec
C
10 msec
80 msec
D
10 msec
160 msec
E
10 msec
320 msec
F
10 msec
640 msec
G
10 msec
1280 msec
For pinouts which offer both SET0 & SET1 pins to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. Two SETx pins offer 3 different time scaling options. The SET[1:0] = 0b'01 combination disables the watchdog operation. showcases an example of the tWD values for different SET[1:0] logic levels when using Watchdog Time setting as option G = 100 msec. The package pin out selected does not offer WD-EN pin.
tWD Scaling with SET0 & SET1
Pins, WD-EN Pin Not Available (Pin Configuration B)
WATCHDOG TIME SCALING SELECTION
tWD
SET[1:0] = 0b'00
SET[1:0] = 0b'01
SET[1:0] = 0b'10
SET[1:0] = 0b'11
A
100 msec
Watchdog disable
200 msec
400 msec
B
100 msec
Watchdog disable
400 msec
800 msec
C
100 msec
Watchdog disable
800 msec
1600 msec
D
100 msec
Watchdog disable
1600 msec
3200 msec
E
100 msec
Watchdog disable
3200 msec
6400 msec
F
100 msec
Watchdog disable
6400 msec
12800 msec
G
100 msec
Watchdog disable
12800 msec
25600 msec
Selected pinout option can offer WD-EN pin along
with SET[1:0] pins (Pin Configuration C, D). With this pinout, the WD-EN pin
controls watchdog enable and disable operation. The SET[1:0] = 0b'01 combination
operates as SET[1:0] = 0b'00.
Make sure the tWD value with SETx multiplier does not exceed 640 sec. If a selection of timer and multiplier results in tWD > 640 sec, the timer value will be restricted to 640 sec.
to diagrams show the timing behavior with respect to SETx status changes.
Watchdog Behavior with SETx Pin Status
Watchdog Operation with 2 SET Pins
Watchdog Operation with 1 SET Pin
Manual RESET
The TPS35 supports
manual reset functionality using MR pin.
MR pin when driven with voltage lower than 0.3 x VDD,
asserts the RESET output. The MR pin has 100 kΩ pull up to VDD. The
MR pin can be left floating. The internal pull up makes
sure the output is not asserted due to MR pin trigger.
The output is deasserted after
MR pin voltage rises above 0.7 x VDD voltage and time tD is elapsed. Refer for more
details.
MR Pin
Response
RESET and WDO Output
The TPS35 device can offer RESET or
RESET with independent WDO output pin. The output configuration is dependent on the
pinout variant selected. For a pinout which has only RESET output, the RESET output
is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold or watchdog timer
error is detected. For a pinout which has independent RESET and WDO output pins, the
RESET output is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold. WDO output is
asserted only when watchdog timer error is detected. RESET error has higher priority
than WDO error. If RESET is asserted when WDO is asserted, the device deasserts the
WDO pin and watchdog is disabled until RESET pin is deasserted and startup delay
frame is terminated.
The output will be asserted for tD
time when any relevant events
described above are detected. The time tD
can be programmed by
connecting a capacitor between CRST pin and GND or device will assert tD
for fixed time duration as
selected by orderable part number. Refer
section for all
available options.
describes the relationship between capacitor value and the time tD
. Make sure the capacitance meets
the recommended operating range. Capacitance outside the recommended range can lead
to incorrect operation of the device.
t
D
(sec) = 4.95 x
106 x CCRST (F)
TPS35 also offers
a unique option of latched output. An orderable with latched output will hold the
output in asserted state indefinitely until the device is power cycled or the error
condition is addressed. If the output is latched due to voltage
supervisor undervoltage detection, the output latch will be released when VDD
voltage rises above the VIT- + VHYS level. If the output is latched
due to MR pin low voltage, the output latch will be released
when MR pin voltage rises above 0.7 x VDD level. If
the output is latched due to watchdog timer error, the output latch will be released
when a WDI negative edge is detected or the device is shutdown and powered up again.
shows
timing behavior of the device with latched output configuration.
Output Latch Timing Behavior
Feature Description
Voltage Supervisor
The TPS35 offers high accuracy
under voltage supervisor function at very low quiescent current. The voltage
supervisor function is always active. After the device powers up from VDD <
VPOR, the RESET and WDO outputs are actively driven when VDD is
greater than VPOR. The device starts monitoring the supply level when the
VDD voltage is greater than 1.04 V. The device holds the RESET pin asserted for
tSTRT + tD time after the VDD > VIT+
(VIT- + VHYS). Refer
for the
tD value computation. For a capacitor based tD delay
option, the RESET is asserted for tSTRT + 2 msec time if the CRST pin is
open.
Device pinout options A to C and J, K offer only RESET output. In these devices the internal RESET output from supervisor and WDO output from watchdog timer are ANDed together to drive the external RESET output.
The supervisor offers wide range of fixed
monitoring thresholds (VIT-) from 1.05 V to 5.40 V in steps of 50 mV. The
device asserts the RESET output when the VDD signal falls below VIT-
threshold. The device offers hysteresis functionality for voltage supervision. This
makes sure the supply has recovered above the monitoring threshold before the RESET
output is deasserted. The TPS35 typical voltage hysteresis
(VHYS) is 5%. Along with the voltage hysteresis, the device keeps the
RESET output asserted for time duration tD after the supply has risen
above VIT+. The RESET output assert duration changes from tD
to tSTRT + tD if the VDD signal is ramping from voltage <
VPOR. The tD time duration can be programmable using an
external capacitor or fixed time options offered by the device.
The typical timing behavior for a voltage
supervisor and the RESET output is showcased in . The voltage
supervisor monitoring output has higher priority over watchdog functionality. If the
device voltage supervisor output is asserted, the watchdog functionality is disabled
including WDO assert control. The device resumes watchdog related functionality only
after the supply is stable and the tD time duration has elapsed.
Voltage Supervisor Timing Diagram
Voltage Supervisor
The TPS35 offers high accuracy
under voltage supervisor function at very low quiescent current. The voltage
supervisor function is always active. After the device powers up from VDD <
VPOR, the RESET and WDO outputs are actively driven when VDD is
greater than VPOR. The device starts monitoring the supply level when the
VDD voltage is greater than 1.04 V. The device holds the RESET pin asserted for
tSTRT + tD time after the VDD > VIT+
(VIT- + VHYS). Refer
for the
tD value computation. For a capacitor based tD delay
option, the RESET is asserted for tSTRT + 2 msec time if the CRST pin is
open.
Device pinout options A to C and J, K offer only RESET output. In these devices the internal RESET output from supervisor and WDO output from watchdog timer are ANDed together to drive the external RESET output.
The supervisor offers wide range of fixed
monitoring thresholds (VIT-) from 1.05 V to 5.40 V in steps of 50 mV. The
device asserts the RESET output when the VDD signal falls below VIT-
threshold. The device offers hysteresis functionality for voltage supervision. This
makes sure the supply has recovered above the monitoring threshold before the RESET
output is deasserted. The TPS35 typical voltage hysteresis
(VHYS) is 5%. Along with the voltage hysteresis, the device keeps the
RESET output asserted for time duration tD after the supply has risen
above VIT+. The RESET output assert duration changes from tD
to tSTRT + tD if the VDD signal is ramping from voltage <
VPOR. The tD time duration can be programmable using an
external capacitor or fixed time options offered by the device.
The typical timing behavior for a voltage
supervisor and the RESET output is showcased in . The voltage
supervisor monitoring output has higher priority over watchdog functionality. If the
device voltage supervisor output is asserted, the watchdog functionality is disabled
including WDO assert control. The device resumes watchdog related functionality only
after the supply is stable and the tD time duration has elapsed.
Voltage Supervisor Timing Diagram
The TPS35 offers high accuracy
under voltage supervisor function at very low quiescent current. The voltage
supervisor function is always active. After the device powers up from VDD <
VPOR, the RESET and WDO outputs are actively driven when VDD is
greater than VPOR. The device starts monitoring the supply level when the
VDD voltage is greater than 1.04 V. The device holds the RESET pin asserted for
tSTRT + tD time after the VDD > VIT+
(VIT- + VHYS). Refer
for the
tD value computation. For a capacitor based tD delay
option, the RESET is asserted for tSTRT + 2 msec time if the CRST pin is
open.
Device pinout options A to C and J, K offer only RESET output. In these devices the internal RESET output from supervisor and WDO output from watchdog timer are ANDed together to drive the external RESET output.
The supervisor offers wide range of fixed
monitoring thresholds (VIT-) from 1.05 V to 5.40 V in steps of 50 mV. The
device asserts the RESET output when the VDD signal falls below VIT-
threshold. The device offers hysteresis functionality for voltage supervision. This
makes sure the supply has recovered above the monitoring threshold before the RESET
output is deasserted. The TPS35 typical voltage hysteresis
(VHYS) is 5%. Along with the voltage hysteresis, the device keeps the
RESET output asserted for time duration tD after the supply has risen
above VIT+. The RESET output assert duration changes from tD
to tSTRT + tD if the VDD signal is ramping from voltage <
VPOR. The tD time duration can be programmable using an
external capacitor or fixed time options offered by the device.
The typical timing behavior for a voltage
supervisor and the RESET output is showcased in . The voltage
supervisor monitoring output has higher priority over watchdog functionality. If the
device voltage supervisor output is asserted, the watchdog functionality is disabled
including WDO assert control. The device resumes watchdog related functionality only
after the supply is stable and the tD time duration has elapsed.
Voltage Supervisor Timing Diagram
The TPS35 offers high accuracy
under voltage supervisor function at very low quiescent current. The voltage
supervisor function is always active. After the device powers up from VDD <
VPOR, the RESET and WDO outputs are actively driven when VDD is
greater than VPOR. The device starts monitoring the supply level when the
VDD voltage is greater than 1.04 V. The device holds the RESET pin asserted for
tSTRT + tD time after the VDD > VIT+
(VIT- + VHYS). Refer
for the
tD value computation. For a capacitor based tD delay
option, the RESET is asserted for tSTRT + 2 msec time if the CRST pin is
open. TPS35PORPORSTRTDIT+IT-HYS
DDSTRTDevice pinout options A to C and J, K offer only RESET output. In these devices the internal RESET output from supervisor and WDO output from watchdog timer are ANDed together to drive the external RESET output.and J, K The supervisor offers wide range of fixed
monitoring thresholds (VIT-) from 1.05 V to 5.40 V in steps of 50 mV. The
device asserts the RESET output when the VDD signal falls below VIT-
threshold. The device offers hysteresis functionality for voltage supervision. This
makes sure the supply has recovered above the monitoring threshold before the RESET
output is deasserted. The TPS35 typical voltage hysteresis
(VHYS) is 5%. Along with the voltage hysteresis, the device keeps the
RESET output asserted for time duration tD after the supply has risen
above VIT+. The RESET output assert duration changes from tD
to tSTRT + tD if the VDD signal is ramping from voltage <
VPOR. The tD time duration can be programmable using an
external capacitor or fixed time options offered by the device.IT-IT-TPS35HYSDIT+DSTRTDPORDThe typical timing behavior for a voltage
supervisor and the RESET output is showcased in . The voltage
supervisor monitoring output has higher priority over watchdog functionality. If the
device voltage supervisor output is asserted, the watchdog functionality is disabled
including WDO assert control. The device resumes watchdog related functionality only
after the supply is stable and the tD time duration has elapsed.D
Voltage Supervisor Timing Diagram
Voltage Supervisor Timing Diagram
Timeout Watchdog Timer
The TPS35 offers high
precision timeout watchdog timer monitoring. The device is available in multiple
pinout options A to K which support multiple features to meet
ever expanding needs of various applications. Make sure a correct pinout is selected
to meet the application needs.
The timeout watchdog is
active when the VDD voltage is higher than the VIT- + VHYS
and the RESET is deasserted after the tD time. The watchdog stays
active as long as VDD > VIT- and watchdog is enabled.
TPS35 family offers various startup time delay options to make
sure enough time is available for the host to complete boot operation. Please refer
for
additional details.
The timeout watchdog timer monitors the WDI pin for falling edge in the time frame defined by tWD time period. Refer
section to arrive at the relevant tWD value needed for application. The timer value is reset when a valid falling edge is detected on WDI pin in the tWD time duration. When a valid WDI transition is not detected in tWD time, the device asserts RESET output for pinout options A, B, C, J and K or WDO output for pinout D. The RESET or WDO is asserted for time tD
. Refer
to arrive at the relevant tD
value needed for application.
shows the basic operation for timeout watchdog timer operation. The TPS35 watchdog functionality supports multiple features. Details are available in following sub sections.
Timeout Watchdog Timer Operation
tWD Timer
The tWD timer for TPS35 can be set using an external capacitor connected between CWD pin and GND pin. This feature is available with pinout options A or B or K. Applications which are space constrained or need timer values which meet offered timer options, can benefit when using pinout options C or D
or J. The TPS35 offers multiple fixed timer options ranging from 1 msec up-to 100 sec.
The TPS35, when using capacitance based timer, senses the capacitance value during the power up or after a RESET event. The capacitor is charged and discharged with known internal current source for one cycle to sense the capacitance value. The sensed value is used to arrive at tWD timer for the watchdog operation. This unique implementation helps reduce the continuous charge and discharge current for the capacitor, thus reducing overall current consumption. Continuous charge and discharge of capacitance creates wider dead time (no watchdog monitor functionality) when capacitor is discharging. The dead time is higher for high value of capacitance. The unique implementation of TPS35 helps avoid the dead time as the capacitance is not continuously charging or discharging under normal operation. Make sure CCWD is < 200 x CCRST for accurate calibration of capacitance. #GUID-126A0EA8-DA64-4C35-A2AC-DECE33E8FC5E/EQUATION-BLOCK_XV1_5Z1_YTB highlights the relationship between tWD in second and CWD capacitance in farad. The tWD timer is 20% accurate for an ideal capacitor. Accuracy of the capacitance will have additional impact on the tWD time. Make sure the capacitance meets the recommended operating range. Capacitance outside the recommended range can lead to incorrect operation of the device.
tWD (sec) = 4.95 x 106 x CCWD (F)
The TPS35 also offers wide selection of high accuracy fixed timer options starting from 1 msec to 100 sec including various industry standard values. The TPS35 fixed time options are ±10% accurate for tWD ≥ 10 msec. For tWD < 10 msec, the accuracy is ±20%. tWD value relevant to application can be identified from the orderable part number. Refer
section to identify mapping of orderable part number to tWD value.
The TPS35 offers flexibility to change the tWD value on the fly by controlling the logic levels on the SETx pins.
section explains the advantages offered by this feature and the device behavior with various SETx pin combinations.
Watchdog Enable Disable Operation
The TPS35 supports
watchdog enable or disable functionality. This functionality is critical for
different use cases as listed below.
Disable watchdog during firmware update to avoid host RESET.
Disable watchdog during software step-by-step debug operation.
Disable watchdog when performing critical task to avoid watchdog error
interrupt.
Keep watchdog disabled until host boots up.
The TPS35 supports
watchdog enable or disable functionality through either WD-EN pin (pin configuration
C) or SET[1:0] = 0b'01 (pin
configuration B) logic combination. For a given pinout
only one of these two methods is available for the user to disable watchdog
operation.
For a pinout which offers a WD-EN pin,
the watchdog enable disable functionality is controlled by the logic state of WD-EN
pin. Drive WD-EN = 1 to enable the watchdog operation or drive WD-EN = 0 to disable
the watchdog operation. The WD-EN pin can be toggled any time during the device
operation. The diagram
shows timing behavior with WD-EN pin control.
Watchdog Enable: WD-EN Pin
Control
SET[1:0] = 0b'01 combination can be
used to disable watchdog operation with a pinout which offers SET1 and SET0 pins,
but does not include WD-EN pin. The SET pin logic states can be changed at any time
during watchdog operation. Refer
section for additional details regarding SET[1:0] pin behavior.
Pinout options A, B, K offer watchdog timer control using a
capacitance connected between CWD and GND pin. A capacitance value higher than
recommended or connect to GND leads to watchdog functionality getting disabled.
Capacitance based disable operation overrides the other two options mentioned above.
Changing capacitance on the fly does not enable or disable watchdog operation. A
power supply recycle or device recovery after UV fault,
MR low event is needed
to detect change in capacitance.
Ongoing watchdog frame is terminated
when watchdog is disabled. WDO stays deasserted when watchdog operation is disabled.
For a pinout with only RESET output, the RESET can assert if supply supervisor
error occurs. When
enabled the device immediately enters tWD
frame and start watchdog
monitoring operation.
tSD Watchdog Start Up Delay
The TPS35 supports watchdog
startup delay feature. This feature is activated after power up or after a RESET assert event or after WDO
assert event. When tSD frame is active, the device monitors the WDI pin
but the WDO output is not asserted. This feature allows time for the host complete
boot process before watchdog monitoring can take over. The start up delay helps
avoid unexpected WDO
or RESET assert events
during boot. The tSD time is predetermined based on the device part
number selected. Refer
section
for details to map the part number to tSD time. Pinout option A, B, K are available only in no delay or 10 sec
start up delay options.
The tSD frame is complete when the time
duration selected for tSD is over or host provides a valid transition on
the WDI pin. The host must provide a valid transition on the WDI pin during
tSD time. The device exits the tSD frame and enters
watchdog monitoring phase after valid WDI transition. Failure to provide valid
transition on WDI pin triggers the watchdog error by asserting the WDO output
pin. For devices with only RESET output, the RESET pin
is asserted.
The tSD frame is not initiated when the
watchdog functionality is enabled using WD-EN pin or SET[1:0] pin combination as described in
section.
shows the
operation for tSD time frame.
tSD Frame
Behavior
SET Pin Behavior
The TPS35 offers one or two SET pins based on the pinout option selected. SET pins offer flexibility to the user to program the tWD timer on the fly to meet various application requirements. Typical use cases where SET pin can be used are:
Use wide timeout timer when host is in sleep mode, change to small timeout operation when host is operational. Watchdog can be used to wake up the host after long duration to perform the application related activities before going back to sleep.
Change to wide timeout timer when performing system critical tasks to make sure the watchdog does not interrupt the critical task. Change timer to application specified interval after the critical task is complete.
The tWD timer value for the device is combination of timer selection based on the CWD pin or fixed timer value along with SET pin logic level. The base tWD timer value is decided based on the Watchdog Time selector in the
section. The SET pin logic level is decoded during the device power up. The SET pin value can be changed any time during the operation. SETx pin change which leads to change of watchdog timer value or enable disable state, terminates the ongoing watchdog frame immediately. SETx pins can be updated when WDO or RESET output is asserted as well. The updated tWD timer value will be applied after output is deasserted and the tSD timer is over or terminated.
For a pinout which offers only SET0 pin to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. showcases an example of the tWD values for different SET0 logic levels when using Watchdog Time setting as option D = 10 msec.
tWD Scaling with SET0 Pin Only (Pin
Configuration A, J)
WATCHDOG TIME SCALING SELECTION
tWD
SET0 = 0
SET0 = 1
A
10 msec
20 msec
B
10 msec
40 msec
C
10 msec
80 msec
D
10 msec
160 msec
E
10 msec
320 msec
F
10 msec
640 msec
G
10 msec
1280 msec
For pinouts which offer both SET0 & SET1 pins to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. Two SETx pins offer 3 different time scaling options. The SET[1:0] = 0b'01 combination disables the watchdog operation. showcases an example of the tWD values for different SET[1:0] logic levels when using Watchdog Time setting as option G = 100 msec. The package pin out selected does not offer WD-EN pin.
tWD Scaling with SET0 & SET1
Pins, WD-EN Pin Not Available (Pin Configuration B)
WATCHDOG TIME SCALING SELECTION
tWD
SET[1:0] = 0b'00
SET[1:0] = 0b'01
SET[1:0] = 0b'10
SET[1:0] = 0b'11
A
100 msec
Watchdog disable
200 msec
400 msec
B
100 msec
Watchdog disable
400 msec
800 msec
C
100 msec
Watchdog disable
800 msec
1600 msec
D
100 msec
Watchdog disable
1600 msec
3200 msec
E
100 msec
Watchdog disable
3200 msec
6400 msec
F
100 msec
Watchdog disable
6400 msec
12800 msec
G
100 msec
Watchdog disable
12800 msec
25600 msec
Selected pinout option can offer WD-EN pin along
with SET[1:0] pins (Pin Configuration C, D). With this pinout, the WD-EN pin
controls watchdog enable and disable operation. The SET[1:0] = 0b'01 combination
operates as SET[1:0] = 0b'00.
Make sure the tWD value with SETx multiplier does not exceed 640 sec. If a selection of timer and multiplier results in tWD > 640 sec, the timer value will be restricted to 640 sec.
to diagrams show the timing behavior with respect to SETx status changes.
Watchdog Behavior with SETx Pin Status
Watchdog Operation with 2 SET Pins
Watchdog Operation with 1 SET Pin
Timeout Watchdog Timer
The TPS35 offers high
precision timeout watchdog timer monitoring. The device is available in multiple
pinout options A to K which support multiple features to meet
ever expanding needs of various applications. Make sure a correct pinout is selected
to meet the application needs.
The timeout watchdog is
active when the VDD voltage is higher than the VIT- + VHYS
and the RESET is deasserted after the tD time. The watchdog stays
active as long as VDD > VIT- and watchdog is enabled.
TPS35 family offers various startup time delay options to make
sure enough time is available for the host to complete boot operation. Please refer
for
additional details.
The timeout watchdog timer monitors the WDI pin for falling edge in the time frame defined by tWD time period. Refer
section to arrive at the relevant tWD value needed for application. The timer value is reset when a valid falling edge is detected on WDI pin in the tWD time duration. When a valid WDI transition is not detected in tWD time, the device asserts RESET output for pinout options A, B, C, J and K or WDO output for pinout D. The RESET or WDO is asserted for time tD
. Refer
to arrive at the relevant tD
value needed for application.
shows the basic operation for timeout watchdog timer operation. The TPS35 watchdog functionality supports multiple features. Details are available in following sub sections.
Timeout Watchdog Timer Operation
The TPS35 offers high
precision timeout watchdog timer monitoring. The device is available in multiple
pinout options A to K which support multiple features to meet
ever expanding needs of various applications. Make sure a correct pinout is selected
to meet the application needs.
The timeout watchdog is
active when the VDD voltage is higher than the VIT- + VHYS
and the RESET is deasserted after the tD time. The watchdog stays
active as long as VDD > VIT- and watchdog is enabled.
TPS35 family offers various startup time delay options to make
sure enough time is available for the host to complete boot operation. Please refer
for
additional details.
The timeout watchdog timer monitors the WDI pin for falling edge in the time frame defined by tWD time period. Refer
section to arrive at the relevant tWD value needed for application. The timer value is reset when a valid falling edge is detected on WDI pin in the tWD time duration. When a valid WDI transition is not detected in tWD time, the device asserts RESET output for pinout options A, B, C, J and K or WDO output for pinout D. The RESET or WDO is asserted for time tD
. Refer
to arrive at the relevant tD
value needed for application.
shows the basic operation for timeout watchdog timer operation. The TPS35 watchdog functionality supports multiple features. Details are available in following sub sections.
Timeout Watchdog Timer Operation
The TPS35 offers high
precision timeout watchdog timer monitoring. The device is available in multiple
pinout options A to K which support multiple features to meet
ever expanding needs of various applications. Make sure a correct pinout is selected
to meet the application needs.TPS35K
The timeout watchdog is
active when the VDD voltage is higher than the VIT- + VHYS
and the RESET is deasserted after the tD time. The watchdog stays
active as long as VDD > VIT- and watchdog is enabled.
TPS35 family offers various startup time delay options to make
sure enough time is available for the host to complete boot operation. Please refer
for
additional details.The timeout watchdog is
active when the VDD voltage is higher than the VIT- + VHYS
and the RESET is deasserted after the tD time. The watchdog stays
active as long as VDD > VIT- and watchdog is enabled.IT-HYSDIT-TPS35
The timeout watchdog timer monitors the WDI pin for falling edge in the time frame defined by tWD time period. Refer
section to arrive at the relevant tWD value needed for application. The timer value is reset when a valid falling edge is detected on WDI pin in the tWD time duration. When a valid WDI transition is not detected in tWD time, the device asserts RESET output for pinout options A, B, C, J and K or WDO output for pinout D. The RESET or WDO is asserted for time tD
. Refer
to arrive at the relevant tD
value needed for application.WD
WDWDWDthe device asserts RESET output for pinout options A, B, C, J and K or WDO output for pinout DRESET or tD
D
tD
D
shows the basic operation for timeout watchdog timer operation. The TPS35 watchdog functionality supports multiple features. Details are available in following sub sections.TPS35
Timeout Watchdog Timer Operation
Timeout Watchdog Timer Operation
tWD Timer
The tWD timer for TPS35 can be set using an external capacitor connected between CWD pin and GND pin. This feature is available with pinout options A or B or K. Applications which are space constrained or need timer values which meet offered timer options, can benefit when using pinout options C or D
or J. The TPS35 offers multiple fixed timer options ranging from 1 msec up-to 100 sec.
The TPS35, when using capacitance based timer, senses the capacitance value during the power up or after a RESET event. The capacitor is charged and discharged with known internal current source for one cycle to sense the capacitance value. The sensed value is used to arrive at tWD timer for the watchdog operation. This unique implementation helps reduce the continuous charge and discharge current for the capacitor, thus reducing overall current consumption. Continuous charge and discharge of capacitance creates wider dead time (no watchdog monitor functionality) when capacitor is discharging. The dead time is higher for high value of capacitance. The unique implementation of TPS35 helps avoid the dead time as the capacitance is not continuously charging or discharging under normal operation. Make sure CCWD is < 200 x CCRST for accurate calibration of capacitance. #GUID-126A0EA8-DA64-4C35-A2AC-DECE33E8FC5E/EQUATION-BLOCK_XV1_5Z1_YTB highlights the relationship between tWD in second and CWD capacitance in farad. The tWD timer is 20% accurate for an ideal capacitor. Accuracy of the capacitance will have additional impact on the tWD time. Make sure the capacitance meets the recommended operating range. Capacitance outside the recommended range can lead to incorrect operation of the device.
tWD (sec) = 4.95 x 106 x CCWD (F)
The TPS35 also offers wide selection of high accuracy fixed timer options starting from 1 msec to 100 sec including various industry standard values. The TPS35 fixed time options are ±10% accurate for tWD ≥ 10 msec. For tWD < 10 msec, the accuracy is ±20%. tWD value relevant to application can be identified from the orderable part number. Refer
section to identify mapping of orderable part number to tWD value.
The TPS35 offers flexibility to change the tWD value on the fly by controlling the logic levels on the SETx pins.
section explains the advantages offered by this feature and the device behavior with various SETx pin combinations.
tWD TimerWD
The tWD timer for TPS35 can be set using an external capacitor connected between CWD pin and GND pin. This feature is available with pinout options A or B or K. Applications which are space constrained or need timer values which meet offered timer options, can benefit when using pinout options C or D
or J. The TPS35 offers multiple fixed timer options ranging from 1 msec up-to 100 sec.
The TPS35, when using capacitance based timer, senses the capacitance value during the power up or after a RESET event. The capacitor is charged and discharged with known internal current source for one cycle to sense the capacitance value. The sensed value is used to arrive at tWD timer for the watchdog operation. This unique implementation helps reduce the continuous charge and discharge current for the capacitor, thus reducing overall current consumption. Continuous charge and discharge of capacitance creates wider dead time (no watchdog monitor functionality) when capacitor is discharging. The dead time is higher for high value of capacitance. The unique implementation of TPS35 helps avoid the dead time as the capacitance is not continuously charging or discharging under normal operation. Make sure CCWD is < 200 x CCRST for accurate calibration of capacitance. #GUID-126A0EA8-DA64-4C35-A2AC-DECE33E8FC5E/EQUATION-BLOCK_XV1_5Z1_YTB highlights the relationship between tWD in second and CWD capacitance in farad. The tWD timer is 20% accurate for an ideal capacitor. Accuracy of the capacitance will have additional impact on the tWD time. Make sure the capacitance meets the recommended operating range. Capacitance outside the recommended range can lead to incorrect operation of the device.
tWD (sec) = 4.95 x 106 x CCWD (F)
The TPS35 also offers wide selection of high accuracy fixed timer options starting from 1 msec to 100 sec including various industry standard values. The TPS35 fixed time options are ±10% accurate for tWD ≥ 10 msec. For tWD < 10 msec, the accuracy is ±20%. tWD value relevant to application can be identified from the orderable part number. Refer
section to identify mapping of orderable part number to tWD value.
The TPS35 offers flexibility to change the tWD value on the fly by controlling the logic levels on the SETx pins.
section explains the advantages offered by this feature and the device behavior with various SETx pin combinations.
The tWD timer for TPS35 can be set using an external capacitor connected between CWD pin and GND pin. This feature is available with pinout options A or B or K. Applications which are space constrained or need timer values which meet offered timer options, can benefit when using pinout options C or D
or J. The TPS35 offers multiple fixed timer options ranging from 1 msec up-to 100 sec.
The TPS35, when using capacitance based timer, senses the capacitance value during the power up or after a RESET event. The capacitor is charged and discharged with known internal current source for one cycle to sense the capacitance value. The sensed value is used to arrive at tWD timer for the watchdog operation. This unique implementation helps reduce the continuous charge and discharge current for the capacitor, thus reducing overall current consumption. Continuous charge and discharge of capacitance creates wider dead time (no watchdog monitor functionality) when capacitor is discharging. The dead time is higher for high value of capacitance. The unique implementation of TPS35 helps avoid the dead time as the capacitance is not continuously charging or discharging under normal operation. Make sure CCWD is < 200 x CCRST for accurate calibration of capacitance. #GUID-126A0EA8-DA64-4C35-A2AC-DECE33E8FC5E/EQUATION-BLOCK_XV1_5Z1_YTB highlights the relationship between tWD in second and CWD capacitance in farad. The tWD timer is 20% accurate for an ideal capacitor. Accuracy of the capacitance will have additional impact on the tWD time. Make sure the capacitance meets the recommended operating range. Capacitance outside the recommended range can lead to incorrect operation of the device.
tWD (sec) = 4.95 x 106 x CCWD (F)
The TPS35 also offers wide selection of high accuracy fixed timer options starting from 1 msec to 100 sec including various industry standard values. The TPS35 fixed time options are ±10% accurate for tWD ≥ 10 msec. For tWD < 10 msec, the accuracy is ±20%. tWD value relevant to application can be identified from the orderable part number. Refer
section to identify mapping of orderable part number to tWD value.
The TPS35 offers flexibility to change the tWD value on the fly by controlling the logic levels on the SETx pins.
section explains the advantages offered by this feature and the device behavior with various SETx pin combinations.
The tWD timer for TPS35 can be set using an external capacitor connected between CWD pin and GND pin. This feature is available with pinout options A or B or K. Applications which are space constrained or need timer values which meet offered timer options, can benefit when using pinout options C or D
or J. The TPS35 offers multiple fixed timer options ranging from 1 msec up-to 100 sec.WDTPS35 or K or D or JTPS35The TPS35, when using capacitance based timer, senses the capacitance value during the power up or after a RESET event. The capacitor is charged and discharged with known internal current source for one cycle to sense the capacitance value. The sensed value is used to arrive at tWD timer for the watchdog operation. This unique implementation helps reduce the continuous charge and discharge current for the capacitor, thus reducing overall current consumption. Continuous charge and discharge of capacitance creates wider dead time (no watchdog monitor functionality) when capacitor is discharging. The dead time is higher for high value of capacitance. The unique implementation of TPS35 helps avoid the dead time as the capacitance is not continuously charging or discharging under normal operation. Make sure CCWD is < 200 x CCRST for accurate calibration of capacitance. #GUID-126A0EA8-DA64-4C35-A2AC-DECE33E8FC5E/EQUATION-BLOCK_XV1_5Z1_YTB highlights the relationship between tWD in second and CWD capacitance in farad. The tWD timer is 20% accurate for an ideal capacitor. Accuracy of the capacitance will have additional impact on the tWD time. Make sure the capacitance meets the recommended operating range. Capacitance outside the recommended range can lead to incorrect operation of the device.TPS35 or after a RESET eventWDTPS35CWDCRST#GUID-126A0EA8-DA64-4C35-A2AC-DECE33E8FC5E/EQUATION-BLOCK_XV1_5Z1_YTBWDWDWD
tWD (sec) = 4.95 x 106 x CCWD (F)
tWD (sec) = 4.95 x 106 x CCWD (F)WD6CWDThe TPS35 also offers wide selection of high accuracy fixed timer options starting from 1 msec to 100 sec including various industry standard values. The TPS35 fixed time options are ±10% accurate for tWD ≥ 10 msec. For tWD < 10 msec, the accuracy is ±20%. tWD value relevant to application can be identified from the orderable part number. Refer
section to identify mapping of orderable part number to tWD value.TPS35TPS35WDWDWD
WDThe TPS35 offers flexibility to change the tWD value on the fly by controlling the logic levels on the SETx pins.
section explains the advantages offered by this feature and the device behavior with various SETx pin combinations.TPS35WD
Watchdog Enable Disable Operation
The TPS35 supports
watchdog enable or disable functionality. This functionality is critical for
different use cases as listed below.
Disable watchdog during firmware update to avoid host RESET.
Disable watchdog during software step-by-step debug operation.
Disable watchdog when performing critical task to avoid watchdog error
interrupt.
Keep watchdog disabled until host boots up.
The TPS35 supports
watchdog enable or disable functionality through either WD-EN pin (pin configuration
C) or SET[1:0] = 0b'01 (pin
configuration B) logic combination. For a given pinout
only one of these two methods is available for the user to disable watchdog
operation.
For a pinout which offers a WD-EN pin,
the watchdog enable disable functionality is controlled by the logic state of WD-EN
pin. Drive WD-EN = 1 to enable the watchdog operation or drive WD-EN = 0 to disable
the watchdog operation. The WD-EN pin can be toggled any time during the device
operation. The diagram
shows timing behavior with WD-EN pin control.
Watchdog Enable: WD-EN Pin
Control
SET[1:0] = 0b'01 combination can be
used to disable watchdog operation with a pinout which offers SET1 and SET0 pins,
but does not include WD-EN pin. The SET pin logic states can be changed at any time
during watchdog operation. Refer
section for additional details regarding SET[1:0] pin behavior.
Pinout options A, B, K offer watchdog timer control using a
capacitance connected between CWD and GND pin. A capacitance value higher than
recommended or connect to GND leads to watchdog functionality getting disabled.
Capacitance based disable operation overrides the other two options mentioned above.
Changing capacitance on the fly does not enable or disable watchdog operation. A
power supply recycle or device recovery after UV fault,
MR low event is needed
to detect change in capacitance.
Ongoing watchdog frame is terminated
when watchdog is disabled. WDO stays deasserted when watchdog operation is disabled.
For a pinout with only RESET output, the RESET can assert if supply supervisor
error occurs. When
enabled the device immediately enters tWD
frame and start watchdog
monitoring operation.
Watchdog Enable Disable Operation
The TPS35 supports
watchdog enable or disable functionality. This functionality is critical for
different use cases as listed below.
Disable watchdog during firmware update to avoid host RESET.
Disable watchdog during software step-by-step debug operation.
Disable watchdog when performing critical task to avoid watchdog error
interrupt.
Keep watchdog disabled until host boots up.
The TPS35 supports
watchdog enable or disable functionality through either WD-EN pin (pin configuration
C) or SET[1:0] = 0b'01 (pin
configuration B) logic combination. For a given pinout
only one of these two methods is available for the user to disable watchdog
operation.
For a pinout which offers a WD-EN pin,
the watchdog enable disable functionality is controlled by the logic state of WD-EN
pin. Drive WD-EN = 1 to enable the watchdog operation or drive WD-EN = 0 to disable
the watchdog operation. The WD-EN pin can be toggled any time during the device
operation. The diagram
shows timing behavior with WD-EN pin control.
Watchdog Enable: WD-EN Pin
Control
SET[1:0] = 0b'01 combination can be
used to disable watchdog operation with a pinout which offers SET1 and SET0 pins,
but does not include WD-EN pin. The SET pin logic states can be changed at any time
during watchdog operation. Refer
section for additional details regarding SET[1:0] pin behavior.
Pinout options A, B, K offer watchdog timer control using a
capacitance connected between CWD and GND pin. A capacitance value higher than
recommended or connect to GND leads to watchdog functionality getting disabled.
Capacitance based disable operation overrides the other two options mentioned above.
Changing capacitance on the fly does not enable or disable watchdog operation. A
power supply recycle or device recovery after UV fault,
MR low event is needed
to detect change in capacitance.
Ongoing watchdog frame is terminated
when watchdog is disabled. WDO stays deasserted when watchdog operation is disabled.
For a pinout with only RESET output, the RESET can assert if supply supervisor
error occurs. When
enabled the device immediately enters tWD
frame and start watchdog
monitoring operation.
The TPS35 supports
watchdog enable or disable functionality. This functionality is critical for
different use cases as listed below.
Disable watchdog during firmware update to avoid host RESET.
Disable watchdog during software step-by-step debug operation.
Disable watchdog when performing critical task to avoid watchdog error
interrupt.
Keep watchdog disabled until host boots up.
The TPS35 supports
watchdog enable or disable functionality through either WD-EN pin (pin configuration
C) or SET[1:0] = 0b'01 (pin
configuration B) logic combination. For a given pinout
only one of these two methods is available for the user to disable watchdog
operation.
For a pinout which offers a WD-EN pin,
the watchdog enable disable functionality is controlled by the logic state of WD-EN
pin. Drive WD-EN = 1 to enable the watchdog operation or drive WD-EN = 0 to disable
the watchdog operation. The WD-EN pin can be toggled any time during the device
operation. The diagram
shows timing behavior with WD-EN pin control.
Watchdog Enable: WD-EN Pin
Control
SET[1:0] = 0b'01 combination can be
used to disable watchdog operation with a pinout which offers SET1 and SET0 pins,
but does not include WD-EN pin. The SET pin logic states can be changed at any time
during watchdog operation. Refer
section for additional details regarding SET[1:0] pin behavior.
Pinout options A, B, K offer watchdog timer control using a
capacitance connected between CWD and GND pin. A capacitance value higher than
recommended or connect to GND leads to watchdog functionality getting disabled.
Capacitance based disable operation overrides the other two options mentioned above.
Changing capacitance on the fly does not enable or disable watchdog operation. A
power supply recycle or device recovery after UV fault,
MR low event is needed
to detect change in capacitance.
Ongoing watchdog frame is terminated
when watchdog is disabled. WDO stays deasserted when watchdog operation is disabled.
For a pinout with only RESET output, the RESET can assert if supply supervisor
error occurs. When
enabled the device immediately enters tWD
frame and start watchdog
monitoring operation.
The TPS35 supports
watchdog enable or disable functionality. This functionality is critical for
different use cases as listed below.TPS35
Disable watchdog during firmware update to avoid host RESET.
Disable watchdog during software step-by-step debug operation.
Disable watchdog when performing critical task to avoid watchdog error
interrupt.
Keep watchdog disabled until host boots up.
Disable watchdog during firmware update to avoid host RESET.Disable watchdog during software step-by-step debug operation.Disable watchdog when performing critical task to avoid watchdog error
interrupt.Keep watchdog disabled until host boots up.The TPS35 supports
watchdog enable or disable functionality through either WD-EN pin (pin configuration
C) or SET[1:0] = 0b'01 (pin
configuration B) logic combination. For a given pinout
only one of these two methods is available for the user to disable watchdog
operation.TPS35For a pinout which offers a WD-EN pin,
the watchdog enable disable functionality is controlled by the logic state of WD-EN
pin. Drive WD-EN = 1 to enable the watchdog operation or drive WD-EN = 0 to disable
the watchdog operation. The WD-EN pin can be toggled any time during the device
operation. The diagram
shows timing behavior with WD-EN pin control.
Watchdog Enable: WD-EN Pin
Control
Watchdog Enable: WD-EN Pin
ControlSET[1:0] = 0b'01 combination can be
used to disable watchdog operation with a pinout which offers SET1 and SET0 pins,
but does not include WD-EN pin. The SET pin logic states can be changed at any time
during watchdog operation. Refer
section for additional details regarding SET[1:0] pin behavior.
Pinout options A, B, K offer watchdog timer control using a
capacitance connected between CWD and GND pin. A capacitance value higher than
recommended or connect to GND leads to watchdog functionality getting disabled.
Capacitance based disable operation overrides the other two options mentioned above.
Changing capacitance on the fly does not enable or disable watchdog operation. A
power supply recycle or device recovery after UV fault,
MR low event is needed
to detect change in capacitance., K or device recovery after UV fault,
MR low eventMROngoing watchdog frame is terminated
when watchdog is disabled. WDO stays deasserted when watchdog operation is disabled.
For a pinout with only RESET output, the RESET can assert if supply supervisor
error occurs. When
enabled the device immediately enters tWD
frame and start watchdog
monitoring operation.For a pinout with only RESET output, the RESET can assert if supply supervisor
error occurs. tWD
WD
tSD Watchdog Start Up Delay
The TPS35 supports watchdog
startup delay feature. This feature is activated after power up or after a RESET assert event or after WDO
assert event. When tSD frame is active, the device monitors the WDI pin
but the WDO output is not asserted. This feature allows time for the host complete
boot process before watchdog monitoring can take over. The start up delay helps
avoid unexpected WDO
or RESET assert events
during boot. The tSD time is predetermined based on the device part
number selected. Refer
section
for details to map the part number to tSD time. Pinout option A, B, K are available only in no delay or 10 sec
start up delay options.
The tSD frame is complete when the time
duration selected for tSD is over or host provides a valid transition on
the WDI pin. The host must provide a valid transition on the WDI pin during
tSD time. The device exits the tSD frame and enters
watchdog monitoring phase after valid WDI transition. Failure to provide valid
transition on WDI pin triggers the watchdog error by asserting the WDO output
pin. For devices with only RESET output, the RESET pin
is asserted.
The tSD frame is not initiated when the
watchdog functionality is enabled using WD-EN pin or SET[1:0] pin combination as described in
section.
shows the
operation for tSD time frame.
tSD Frame
Behavior
tSD Watchdog Start Up DelaySD
The TPS35 supports watchdog
startup delay feature. This feature is activated after power up or after a RESET assert event or after WDO
assert event. When tSD frame is active, the device monitors the WDI pin
but the WDO output is not asserted. This feature allows time for the host complete
boot process before watchdog monitoring can take over. The start up delay helps
avoid unexpected WDO
or RESET assert events
during boot. The tSD time is predetermined based on the device part
number selected. Refer
section
for details to map the part number to tSD time. Pinout option A, B, K are available only in no delay or 10 sec
start up delay options.
The tSD frame is complete when the time
duration selected for tSD is over or host provides a valid transition on
the WDI pin. The host must provide a valid transition on the WDI pin during
tSD time. The device exits the tSD frame and enters
watchdog monitoring phase after valid WDI transition. Failure to provide valid
transition on WDI pin triggers the watchdog error by asserting the WDO output
pin. For devices with only RESET output, the RESET pin
is asserted.
The tSD frame is not initiated when the
watchdog functionality is enabled using WD-EN pin or SET[1:0] pin combination as described in
section.
shows the
operation for tSD time frame.
tSD Frame
Behavior
The TPS35 supports watchdog
startup delay feature. This feature is activated after power up or after a RESET assert event or after WDO
assert event. When tSD frame is active, the device monitors the WDI pin
but the WDO output is not asserted. This feature allows time for the host complete
boot process before watchdog monitoring can take over. The start up delay helps
avoid unexpected WDO
or RESET assert events
during boot. The tSD time is predetermined based on the device part
number selected. Refer
section
for details to map the part number to tSD time. Pinout option A, B, K are available only in no delay or 10 sec
start up delay options.
The tSD frame is complete when the time
duration selected for tSD is over or host provides a valid transition on
the WDI pin. The host must provide a valid transition on the WDI pin during
tSD time. The device exits the tSD frame and enters
watchdog monitoring phase after valid WDI transition. Failure to provide valid
transition on WDI pin triggers the watchdog error by asserting the WDO output
pin. For devices with only RESET output, the RESET pin
is asserted.
The tSD frame is not initiated when the
watchdog functionality is enabled using WD-EN pin or SET[1:0] pin combination as described in
section.
shows the
operation for tSD time frame.
tSD Frame
Behavior
The TPS35 supports watchdog
startup delay feature. This feature is activated after power up or after a RESET assert event or after WDO
assert event. When tSD frame is active, the device monitors the WDI pin
but the WDO output is not asserted. This feature allows time for the host complete
boot process before watchdog monitoring can take over. The start up delay helps
avoid unexpected WDO
or RESET assert events
during boot. The tSD time is predetermined based on the device part
number selected. Refer
section
for details to map the part number to tSD time. Pinout option A, B, K are available only in no delay or 10 sec
start up delay options.TPS35or after a RESET assert event SD
or RESETSD
SD, KThe tSD frame is complete when the time
duration selected for tSD is over or host provides a valid transition on
the WDI pin. The host must provide a valid transition on the WDI pin during
tSD time. The device exits the tSD frame and enters
watchdog monitoring phase after valid WDI transition. Failure to provide valid
transition on WDI pin triggers the watchdog error by asserting the WDO output
pin. For devices with only RESET output, the RESET pin
is asserted.
SDSDSDSD For devices with only RESET output, the RESET pin
is asserted.The tSD frame is not initiated when the
watchdog functionality is enabled using WD-EN pin or SET[1:0] pin combination as described in
section.SD
shows the
operation for tSD time frame.SD
tSD Frame
Behavior
tSD Frame
BehaviorSD
SET Pin Behavior
The TPS35 offers one or two SET pins based on the pinout option selected. SET pins offer flexibility to the user to program the tWD timer on the fly to meet various application requirements. Typical use cases where SET pin can be used are:
Use wide timeout timer when host is in sleep mode, change to small timeout operation when host is operational. Watchdog can be used to wake up the host after long duration to perform the application related activities before going back to sleep.
Change to wide timeout timer when performing system critical tasks to make sure the watchdog does not interrupt the critical task. Change timer to application specified interval after the critical task is complete.
The tWD timer value for the device is combination of timer selection based on the CWD pin or fixed timer value along with SET pin logic level. The base tWD timer value is decided based on the Watchdog Time selector in the
section. The SET pin logic level is decoded during the device power up. The SET pin value can be changed any time during the operation. SETx pin change which leads to change of watchdog timer value or enable disable state, terminates the ongoing watchdog frame immediately. SETx pins can be updated when WDO or RESET output is asserted as well. The updated tWD timer value will be applied after output is deasserted and the tSD timer is over or terminated.
For a pinout which offers only SET0 pin to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. showcases an example of the tWD values for different SET0 logic levels when using Watchdog Time setting as option D = 10 msec.
tWD Scaling with SET0 Pin Only (Pin
Configuration A, J)
WATCHDOG TIME SCALING SELECTION
tWD
SET0 = 0
SET0 = 1
A
10 msec
20 msec
B
10 msec
40 msec
C
10 msec
80 msec
D
10 msec
160 msec
E
10 msec
320 msec
F
10 msec
640 msec
G
10 msec
1280 msec
For pinouts which offer both SET0 & SET1 pins to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. Two SETx pins offer 3 different time scaling options. The SET[1:0] = 0b'01 combination disables the watchdog operation. showcases an example of the tWD values for different SET[1:0] logic levels when using Watchdog Time setting as option G = 100 msec. The package pin out selected does not offer WD-EN pin.
tWD Scaling with SET0 & SET1
Pins, WD-EN Pin Not Available (Pin Configuration B)
WATCHDOG TIME SCALING SELECTION
tWD
SET[1:0] = 0b'00
SET[1:0] = 0b'01
SET[1:0] = 0b'10
SET[1:0] = 0b'11
A
100 msec
Watchdog disable
200 msec
400 msec
B
100 msec
Watchdog disable
400 msec
800 msec
C
100 msec
Watchdog disable
800 msec
1600 msec
D
100 msec
Watchdog disable
1600 msec
3200 msec
E
100 msec
Watchdog disable
3200 msec
6400 msec
F
100 msec
Watchdog disable
6400 msec
12800 msec
G
100 msec
Watchdog disable
12800 msec
25600 msec
Selected pinout option can offer WD-EN pin along
with SET[1:0] pins (Pin Configuration C, D). With this pinout, the WD-EN pin
controls watchdog enable and disable operation. The SET[1:0] = 0b'01 combination
operates as SET[1:0] = 0b'00.
Make sure the tWD value with SETx multiplier does not exceed 640 sec. If a selection of timer and multiplier results in tWD > 640 sec, the timer value will be restricted to 640 sec.
to diagrams show the timing behavior with respect to SETx status changes.
Watchdog Behavior with SETx Pin Status
Watchdog Operation with 2 SET Pins
Watchdog Operation with 1 SET Pin
SET Pin Behavior
The TPS35 offers one or two SET pins based on the pinout option selected. SET pins offer flexibility to the user to program the tWD timer on the fly to meet various application requirements. Typical use cases where SET pin can be used are:
Use wide timeout timer when host is in sleep mode, change to small timeout operation when host is operational. Watchdog can be used to wake up the host after long duration to perform the application related activities before going back to sleep.
Change to wide timeout timer when performing system critical tasks to make sure the watchdog does not interrupt the critical task. Change timer to application specified interval after the critical task is complete.
The tWD timer value for the device is combination of timer selection based on the CWD pin or fixed timer value along with SET pin logic level. The base tWD timer value is decided based on the Watchdog Time selector in the
section. The SET pin logic level is decoded during the device power up. The SET pin value can be changed any time during the operation. SETx pin change which leads to change of watchdog timer value or enable disable state, terminates the ongoing watchdog frame immediately. SETx pins can be updated when WDO or RESET output is asserted as well. The updated tWD timer value will be applied after output is deasserted and the tSD timer is over or terminated.
For a pinout which offers only SET0 pin to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. showcases an example of the tWD values for different SET0 logic levels when using Watchdog Time setting as option D = 10 msec.
tWD Scaling with SET0 Pin Only (Pin
Configuration A, J)
WATCHDOG TIME SCALING SELECTION
tWD
SET0 = 0
SET0 = 1
A
10 msec
20 msec
B
10 msec
40 msec
C
10 msec
80 msec
D
10 msec
160 msec
E
10 msec
320 msec
F
10 msec
640 msec
G
10 msec
1280 msec
For pinouts which offer both SET0 & SET1 pins to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. Two SETx pins offer 3 different time scaling options. The SET[1:0] = 0b'01 combination disables the watchdog operation. showcases an example of the tWD values for different SET[1:0] logic levels when using Watchdog Time setting as option G = 100 msec. The package pin out selected does not offer WD-EN pin.
tWD Scaling with SET0 & SET1
Pins, WD-EN Pin Not Available (Pin Configuration B)
WATCHDOG TIME SCALING SELECTION
tWD
SET[1:0] = 0b'00
SET[1:0] = 0b'01
SET[1:0] = 0b'10
SET[1:0] = 0b'11
A
100 msec
Watchdog disable
200 msec
400 msec
B
100 msec
Watchdog disable
400 msec
800 msec
C
100 msec
Watchdog disable
800 msec
1600 msec
D
100 msec
Watchdog disable
1600 msec
3200 msec
E
100 msec
Watchdog disable
3200 msec
6400 msec
F
100 msec
Watchdog disable
6400 msec
12800 msec
G
100 msec
Watchdog disable
12800 msec
25600 msec
Selected pinout option can offer WD-EN pin along
with SET[1:0] pins (Pin Configuration C, D). With this pinout, the WD-EN pin
controls watchdog enable and disable operation. The SET[1:0] = 0b'01 combination
operates as SET[1:0] = 0b'00.
Make sure the tWD value with SETx multiplier does not exceed 640 sec. If a selection of timer and multiplier results in tWD > 640 sec, the timer value will be restricted to 640 sec.
to diagrams show the timing behavior with respect to SETx status changes.
Watchdog Behavior with SETx Pin Status
Watchdog Operation with 2 SET Pins
Watchdog Operation with 1 SET Pin
The TPS35 offers one or two SET pins based on the pinout option selected. SET pins offer flexibility to the user to program the tWD timer on the fly to meet various application requirements. Typical use cases where SET pin can be used are:
Use wide timeout timer when host is in sleep mode, change to small timeout operation when host is operational. Watchdog can be used to wake up the host after long duration to perform the application related activities before going back to sleep.
Change to wide timeout timer when performing system critical tasks to make sure the watchdog does not interrupt the critical task. Change timer to application specified interval after the critical task is complete.
The tWD timer value for the device is combination of timer selection based on the CWD pin or fixed timer value along with SET pin logic level. The base tWD timer value is decided based on the Watchdog Time selector in the
section. The SET pin logic level is decoded during the device power up. The SET pin value can be changed any time during the operation. SETx pin change which leads to change of watchdog timer value or enable disable state, terminates the ongoing watchdog frame immediately. SETx pins can be updated when WDO or RESET output is asserted as well. The updated tWD timer value will be applied after output is deasserted and the tSD timer is over or terminated.
For a pinout which offers only SET0 pin to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. showcases an example of the tWD values for different SET0 logic levels when using Watchdog Time setting as option D = 10 msec.
tWD Scaling with SET0 Pin Only (Pin
Configuration A, J)
WATCHDOG TIME SCALING SELECTION
tWD
SET0 = 0
SET0 = 1
A
10 msec
20 msec
B
10 msec
40 msec
C
10 msec
80 msec
D
10 msec
160 msec
E
10 msec
320 msec
F
10 msec
640 msec
G
10 msec
1280 msec
For pinouts which offer both SET0 & SET1 pins to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. Two SETx pins offer 3 different time scaling options. The SET[1:0] = 0b'01 combination disables the watchdog operation. showcases an example of the tWD values for different SET[1:0] logic levels when using Watchdog Time setting as option G = 100 msec. The package pin out selected does not offer WD-EN pin.
tWD Scaling with SET0 & SET1
Pins, WD-EN Pin Not Available (Pin Configuration B)
WATCHDOG TIME SCALING SELECTION
tWD
SET[1:0] = 0b'00
SET[1:0] = 0b'01
SET[1:0] = 0b'10
SET[1:0] = 0b'11
A
100 msec
Watchdog disable
200 msec
400 msec
B
100 msec
Watchdog disable
400 msec
800 msec
C
100 msec
Watchdog disable
800 msec
1600 msec
D
100 msec
Watchdog disable
1600 msec
3200 msec
E
100 msec
Watchdog disable
3200 msec
6400 msec
F
100 msec
Watchdog disable
6400 msec
12800 msec
G
100 msec
Watchdog disable
12800 msec
25600 msec
Selected pinout option can offer WD-EN pin along
with SET[1:0] pins (Pin Configuration C, D). With this pinout, the WD-EN pin
controls watchdog enable and disable operation. The SET[1:0] = 0b'01 combination
operates as SET[1:0] = 0b'00.
Make sure the tWD value with SETx multiplier does not exceed 640 sec. If a selection of timer and multiplier results in tWD > 640 sec, the timer value will be restricted to 640 sec.
to diagrams show the timing behavior with respect to SETx status changes.
Watchdog Behavior with SETx Pin Status
Watchdog Operation with 2 SET Pins
Watchdog Operation with 1 SET Pin
The TPS35 offers one or two SET pins based on the pinout option selected. SET pins offer flexibility to the user to program the tWD timer on the fly to meet various application requirements. Typical use cases where SET pin can be used are:
Use wide timeout timer when host is in sleep mode, change to small timeout operation when host is operational. Watchdog can be used to wake up the host after long duration to perform the application related activities before going back to sleep.
Change to wide timeout timer when performing system critical tasks to make sure the watchdog does not interrupt the critical task. Change timer to application specified interval after the critical task is complete.
TPS35WD
Use wide timeout timer when host is in sleep mode, change to small timeout operation when host is operational. Watchdog can be used to wake up the host after long duration to perform the application related activities before going back to sleep.
Change to wide timeout timer when performing system critical tasks to make sure the watchdog does not interrupt the critical task. Change timer to application specified interval after the critical task is complete.
Use wide timeout timer when host is in sleep mode, change to small timeout operation when host is operational. Watchdog can be used to wake up the host after long duration to perform the application related activities before going back to sleep.Change to wide timeout timer when performing system critical tasks to make sure the watchdog does not interrupt the critical task. Change timer to application specified interval after the critical task is complete.The tWD timer value for the device is combination of timer selection based on the CWD pin or fixed timer value along with SET pin logic level. The base tWD timer value is decided based on the Watchdog Time selector in the
section. The SET pin logic level is decoded during the device power up. The SET pin value can be changed any time during the operation. SETx pin change which leads to change of watchdog timer value or enable disable state, terminates the ongoing watchdog frame immediately. SETx pins can be updated when WDO or RESET output is asserted as well. The updated tWD timer value will be applied after output is deasserted and the tSD timer is over or terminated.WDWD
or RESETWDSDFor a pinout which offers only SET0 pin to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. showcases an example of the tWD values for different SET0 logic levels when using Watchdog Time setting as option D = 10 msec.WD
WD
tWD Scaling with SET0 Pin Only (Pin
Configuration A, J)
WATCHDOG TIME SCALING SELECTION
tWD
SET0 = 0
SET0 = 1
A
10 msec
20 msec
B
10 msec
40 msec
C
10 msec
80 msec
D
10 msec
160 msec
E
10 msec
320 msec
F
10 msec
640 msec
G
10 msec
1280 msec
tWD Scaling with SET0 Pin Only (Pin
Configuration A, J)WD, J
WATCHDOG TIME SCALING SELECTION
tWD
SET0 = 0
SET0 = 1
A
10 msec
20 msec
B
10 msec
40 msec
C
10 msec
80 msec
D
10 msec
160 msec
E
10 msec
320 msec
F
10 msec
640 msec
G
10 msec
1280 msec
WATCHDOG TIME SCALING SELECTION
tWD
SET0 = 0
SET0 = 1
WATCHDOG TIME SCALING SELECTION
tWD
WATCHDOG TIME SCALING SELECTIONtWD
WD
SET0 = 0
SET0 = 1
SET0 = 0SET0 = 1
A
10 msec
20 msec
B
10 msec
40 msec
C
10 msec
80 msec
D
10 msec
160 msec
E
10 msec
320 msec
F
10 msec
640 msec
G
10 msec
1280 msec
A
10 msec
20 msec
A10 msec20 msec
B
10 msec
40 msec
B10 msec40 msec
C
10 msec
80 msec
C10 msec80 msec
D
10 msec
160 msec
D10 msec160 msec
E
10 msec
320 msec
E10 msec320 msec
F
10 msec
640 msec
F10 msec640 msec
G
10 msec
1280 msec
G10 msec1280 msecFor pinouts which offer both SET0 & SET1 pins to the user, the tWD multiplier value is decided based on the Watchdog Time Scaling selector in the
section. Two SETx pins offer 3 different time scaling options. The SET[1:0] = 0b'01 combination disables the watchdog operation. showcases an example of the tWD values for different SET[1:0] logic levels when using Watchdog Time setting as option G = 100 msec. The package pin out selected does not offer WD-EN pin.WD
WD
tWD Scaling with SET0 & SET1
Pins, WD-EN Pin Not Available (Pin Configuration B)
WATCHDOG TIME SCALING SELECTION
tWD
SET[1:0] = 0b'00
SET[1:0] = 0b'01
SET[1:0] = 0b'10
SET[1:0] = 0b'11
A
100 msec
Watchdog disable
200 msec
400 msec
B
100 msec
Watchdog disable
400 msec
800 msec
C
100 msec
Watchdog disable
800 msec
1600 msec
D
100 msec
Watchdog disable
1600 msec
3200 msec
E
100 msec
Watchdog disable
3200 msec
6400 msec
F
100 msec
Watchdog disable
6400 msec
12800 msec
G
100 msec
Watchdog disable
12800 msec
25600 msec
tWD Scaling with SET0 & SET1
Pins, WD-EN Pin Not Available (Pin Configuration B)WD
WATCHDOG TIME SCALING SELECTION
tWD
SET[1:0] = 0b'00
SET[1:0] = 0b'01
SET[1:0] = 0b'10
SET[1:0] = 0b'11
A
100 msec
Watchdog disable
200 msec
400 msec
B
100 msec
Watchdog disable
400 msec
800 msec
C
100 msec
Watchdog disable
800 msec
1600 msec
D
100 msec
Watchdog disable
1600 msec
3200 msec
E
100 msec
Watchdog disable
3200 msec
6400 msec
F
100 msec
Watchdog disable
6400 msec
12800 msec
G
100 msec
Watchdog disable
12800 msec
25600 msec
WATCHDOG TIME SCALING SELECTION
tWD
SET[1:0] = 0b'00
SET[1:0] = 0b'01
SET[1:0] = 0b'10
SET[1:0] = 0b'11
WATCHDOG TIME SCALING SELECTION
tWD
WATCHDOG TIME SCALING SELECTIONtWD
WD
SET[1:0] = 0b'00
SET[1:0] = 0b'01
SET[1:0] = 0b'10
SET[1:0] = 0b'11
SET[1:0] = 0b'00SET[1:0] = 0b'01SET[1:0] = 0b'10SET[1:0] = 0b'11
A
100 msec
Watchdog disable
200 msec
400 msec
B
100 msec
Watchdog disable
400 msec
800 msec
C
100 msec
Watchdog disable
800 msec
1600 msec
D
100 msec
Watchdog disable
1600 msec
3200 msec
E
100 msec
Watchdog disable
3200 msec
6400 msec
F
100 msec
Watchdog disable
6400 msec
12800 msec
G
100 msec
Watchdog disable
12800 msec
25600 msec
A
100 msec
Watchdog disable
200 msec
400 msec
A100 msecWatchdog disable200 msec400 msec
B
100 msec
Watchdog disable
400 msec
800 msec
B100 msecWatchdog disable400 msec800 msec
C
100 msec
Watchdog disable
800 msec
1600 msec
C100 msecWatchdog disable800 msec1600 msec
D
100 msec
Watchdog disable
1600 msec
3200 msec
D100 msecWatchdog disable1600 msec3200 msec
E
100 msec
Watchdog disable
3200 msec
6400 msec
E100 msecWatchdog disable3200 msec6400 msec
F
100 msec
Watchdog disable
6400 msec
12800 msec
F100 msecWatchdog disable6400 msec12800 msec
G
100 msec
Watchdog disable
12800 msec
25600 msec
G100 msecWatchdog disable12800 msec25600 msecSelected pinout option can offer WD-EN pin along
with SET[1:0] pins (Pin Configuration C, D). With this pinout, the WD-EN pin
controls watchdog enable and disable operation. The SET[1:0] = 0b'01 combination
operates as SET[1:0] = 0b'00. , DMake sure the tWD value with SETx multiplier does not exceed 640 sec. If a selection of timer and multiplier results in tWD > 640 sec, the timer value will be restricted to 640 sec.WDWD
to diagrams show the timing behavior with respect to SETx status changes.
Watchdog Behavior with SETx Pin Status
Watchdog Behavior with SETx Pin Status
Watchdog Operation with 2 SET Pins
Watchdog Operation with 2 SET Pins
Watchdog Operation with 1 SET Pin
Watchdog Operation with 1 SET Pin
Manual RESET
The TPS35 supports
manual reset functionality using MR pin.
MR pin when driven with voltage lower than 0.3 x VDD,
asserts the RESET output. The MR pin has 100 kΩ pull up to VDD. The
MR pin can be left floating. The internal pull up makes
sure the output is not asserted due to MR pin trigger.
The output is deasserted after
MR pin voltage rises above 0.7 x VDD voltage and time tD is elapsed. Refer for more
details.
MR Pin
Response
Manual RESET
The TPS35 supports
manual reset functionality using MR pin.
MR pin when driven with voltage lower than 0.3 x VDD,
asserts the RESET output. The MR pin has 100 kΩ pull up to VDD. The
MR pin can be left floating. The internal pull up makes
sure the output is not asserted due to MR pin trigger.
The output is deasserted after
MR pin voltage rises above 0.7 x VDD voltage and time tD is elapsed. Refer for more
details.
MR Pin
Response
The TPS35 supports
manual reset functionality using MR pin.
MR pin when driven with voltage lower than 0.3 x VDD,
asserts the RESET output. The MR pin has 100 kΩ pull up to VDD. The
MR pin can be left floating. The internal pull up makes
sure the output is not asserted due to MR pin trigger.
The output is deasserted after
MR pin voltage rises above 0.7 x VDD voltage and time tD is elapsed. Refer for more
details.
MR Pin
Response
The TPS35 supports
manual reset functionality using MR pin.
MR pin when driven with voltage lower than 0.3 x VDD,
asserts the RESET output. The MR pin has 100 kΩ pull up to VDD. The
MR pin can be left floating. The internal pull up makes
sure the output is not asserted due to MR pin trigger.TPS35MRMRRESETMRMRMRThe output is deasserted after
MR pin voltage rises above 0.7 x VDD voltage and time tD is elapsed. Refer for more
details.MR and time tD is elapsedD
MR Pin
Response
MR Pin
ResponseMR
RESET and WDO Output
The TPS35 device can offer RESET or
RESET with independent WDO output pin. The output configuration is dependent on the
pinout variant selected. For a pinout which has only RESET output, the RESET output
is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold or watchdog timer
error is detected. For a pinout which has independent RESET and WDO output pins, the
RESET output is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold. WDO output is
asserted only when watchdog timer error is detected. RESET error has higher priority
than WDO error. If RESET is asserted when WDO is asserted, the device deasserts the
WDO pin and watchdog is disabled until RESET pin is deasserted and startup delay
frame is terminated.
The output will be asserted for tD
time when any relevant events
described above are detected. The time tD
can be programmed by
connecting a capacitor between CRST pin and GND or device will assert tD
for fixed time duration as
selected by orderable part number. Refer
section for all
available options.
describes the relationship between capacitor value and the time tD
. Make sure the capacitance meets
the recommended operating range. Capacitance outside the recommended range can lead
to incorrect operation of the device.
t
D
(sec) = 4.95 x
106 x CCRST (F)
TPS35 also offers
a unique option of latched output. An orderable with latched output will hold the
output in asserted state indefinitely until the device is power cycled or the error
condition is addressed. If the output is latched due to voltage
supervisor undervoltage detection, the output latch will be released when VDD
voltage rises above the VIT- + VHYS level. If the output is latched
due to MR pin low voltage, the output latch will be released
when MR pin voltage rises above 0.7 x VDD level. If
the output is latched due to watchdog timer error, the output latch will be released
when a WDI negative edge is detected or the device is shutdown and powered up again.
shows
timing behavior of the device with latched output configuration.
Output Latch Timing Behavior
RESET and WDO OutputRESET and
The TPS35 device can offer RESET or
RESET with independent WDO output pin. The output configuration is dependent on the
pinout variant selected. For a pinout which has only RESET output, the RESET output
is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold or watchdog timer
error is detected. For a pinout which has independent RESET and WDO output pins, the
RESET output is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold. WDO output is
asserted only when watchdog timer error is detected. RESET error has higher priority
than WDO error. If RESET is asserted when WDO is asserted, the device deasserts the
WDO pin and watchdog is disabled until RESET pin is deasserted and startup delay
frame is terminated.
The output will be asserted for tD
time when any relevant events
described above are detected. The time tD
can be programmed by
connecting a capacitor between CRST pin and GND or device will assert tD
for fixed time duration as
selected by orderable part number. Refer
section for all
available options.
describes the relationship between capacitor value and the time tD
. Make sure the capacitance meets
the recommended operating range. Capacitance outside the recommended range can lead
to incorrect operation of the device.
t
D
(sec) = 4.95 x
106 x CCRST (F)
TPS35 also offers
a unique option of latched output. An orderable with latched output will hold the
output in asserted state indefinitely until the device is power cycled or the error
condition is addressed. If the output is latched due to voltage
supervisor undervoltage detection, the output latch will be released when VDD
voltage rises above the VIT- + VHYS level. If the output is latched
due to MR pin low voltage, the output latch will be released
when MR pin voltage rises above 0.7 x VDD level. If
the output is latched due to watchdog timer error, the output latch will be released
when a WDI negative edge is detected or the device is shutdown and powered up again.
shows
timing behavior of the device with latched output configuration.
Output Latch Timing Behavior
The TPS35 device can offer RESET or
RESET with independent WDO output pin. The output configuration is dependent on the
pinout variant selected. For a pinout which has only RESET output, the RESET output
is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold or watchdog timer
error is detected. For a pinout which has independent RESET and WDO output pins, the
RESET output is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold. WDO output is
asserted only when watchdog timer error is detected. RESET error has higher priority
than WDO error. If RESET is asserted when WDO is asserted, the device deasserts the
WDO pin and watchdog is disabled until RESET pin is deasserted and startup delay
frame is terminated.
The output will be asserted for tD
time when any relevant events
described above are detected. The time tD
can be programmed by
connecting a capacitor between CRST pin and GND or device will assert tD
for fixed time duration as
selected by orderable part number. Refer
section for all
available options.
describes the relationship between capacitor value and the time tD
. Make sure the capacitance meets
the recommended operating range. Capacitance outside the recommended range can lead
to incorrect operation of the device.
t
D
(sec) = 4.95 x
106 x CCRST (F)
TPS35 also offers
a unique option of latched output. An orderable with latched output will hold the
output in asserted state indefinitely until the device is power cycled or the error
condition is addressed. If the output is latched due to voltage
supervisor undervoltage detection, the output latch will be released when VDD
voltage rises above the VIT- + VHYS level. If the output is latched
due to MR pin low voltage, the output latch will be released
when MR pin voltage rises above 0.7 x VDD level. If
the output is latched due to watchdog timer error, the output latch will be released
when a WDI negative edge is detected or the device is shutdown and powered up again.
shows
timing behavior of the device with latched output configuration.
Output Latch Timing Behavior
The TPS35 device can offer RESET or
RESET with independent WDO output pin. The output configuration is dependent on the
pinout variant selected. For a pinout which has only RESET output, the RESET output
is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold or watchdog timer
error is detected. For a pinout which has independent RESET and WDO output pins, the
RESET output is asserted when VDD voltage is below the monitored threshold or
MR pin voltage is lower than threshold. WDO output is
asserted only when watchdog timer error is detected. RESET error has higher priority
than WDO error. If RESET is asserted when WDO is asserted, the device deasserts the
WDO pin and watchdog is disabled until RESET pin is deasserted and startup delay
frame is terminated.TPS35MRMRThe output will be asserted for tD
time when any relevant events
described above are detected. The time tD
can be programmed by
connecting a capacitor between CRST pin and GND or device will assert tD
for fixed time duration as
selected by orderable part number. Refer
section for all
available options.tD
DtD
DtD
D
describes the relationship between capacitor value and the time tD
. Make sure the capacitance meets
the recommended operating range. Capacitance outside the recommended range can lead
to incorrect operation of the device.tD
D
t
D
(sec) = 4.95 x
106 x CCRST (F)
t
D
(sec) = 4.95 x
106 x CCRST (F)
D
D6CRST
TPS35 also offers
a unique option of latched output. An orderable with latched output will hold the
output in asserted state indefinitely until the device is power cycled or the error
condition is addressed. If the output is latched due to voltage
supervisor undervoltage detection, the output latch will be released when VDD
voltage rises above the VIT- + VHYS level. If the output is latched
due to MR pin low voltage, the output latch will be released
when MR pin voltage rises above 0.7 x VDD level. If
the output is latched due to watchdog timer error, the output latch will be released
when a WDI negative edge is detected or the device is shutdown and powered up again.
shows
timing behavior of the device with latched output configuration.TPS35If the output is latched due to voltage
supervisor undervoltage detection, the output latch will be released when VDD
voltage rises above the VIT- + VHYS level. IT-HYSMRMRDD
Output Latch Timing Behavior
Output Latch Timing Behavior
Device Functional Modes
#GUID-B008A25A-278A-4B38-AFBB-A738DE66DE26/TABLE_TV3_FWV_HVB
summarizes the functional modes of the TPS35.
Device Functional
Modes
VDD
WATCHDOG STATUS
WDI
WDO
RESET
VDD <
VPOR
Not Applicable
—
Undefined
Undefined
VPOR ≤
VDD < VIT-
Not Applicable
Ignored
High
Low
VDD ≥ VIT+
Disabled
Ignored
High
High
Enabled
tpulse
1 < tWD(min)
High
High
Enabled
tpulse
1 > tWD(max)
Low
High
Where tpulse is the time between falling edges on
WDI.
Device Functional Modes
#GUID-B008A25A-278A-4B38-AFBB-A738DE66DE26/TABLE_TV3_FWV_HVB
summarizes the functional modes of the TPS35.
Device Functional
Modes
VDD
WATCHDOG STATUS
WDI
WDO
RESET
VDD <
VPOR
Not Applicable
—
Undefined
Undefined
VPOR ≤
VDD < VIT-
Not Applicable
Ignored
High
Low
VDD ≥ VIT+
Disabled
Ignored
High
High
Enabled
tpulse
1 < tWD(min)
High
High
Enabled
tpulse
1 > tWD(max)
Low
High
Where tpulse is the time between falling edges on
WDI.
#GUID-B008A25A-278A-4B38-AFBB-A738DE66DE26/TABLE_TV3_FWV_HVB
summarizes the functional modes of the TPS35.
Device Functional
Modes
VDD
WATCHDOG STATUS
WDI
WDO
RESET
VDD <
VPOR
Not Applicable
—
Undefined
Undefined
VPOR ≤
VDD < VIT-
Not Applicable
Ignored
High
Low
VDD ≥ VIT+
Disabled
Ignored
High
High
Enabled
tpulse
1 < tWD(min)
High
High
Enabled
tpulse
1 > tWD(max)
Low
High
Where tpulse is the time between falling edges on
WDI.
#GUID-B008A25A-278A-4B38-AFBB-A738DE66DE26/TABLE_TV3_FWV_HVB
summarizes the functional modes of the TPS35.
#GUID-B008A25A-278A-4B38-AFBB-A738DE66DE26/TABLE_TV3_FWV_HVB
#GUID-B008A25A-278A-4B38-AFBB-A738DE66DE26/TABLE_TV3_FWV_HVBTPS35
Device Functional
Modes
VDD
WATCHDOG STATUS
WDI
WDO
RESET
VDD <
VPOR
Not Applicable
—
Undefined
Undefined
VPOR ≤
VDD < VIT-
Not Applicable
Ignored
High
Low
VDD ≥ VIT+
Disabled
Ignored
High
High
Enabled
tpulse
1 < tWD(min)
High
High
Enabled
tpulse
1 > tWD(max)
Low
High
Device Functional
Modes
VDD
WATCHDOG STATUS
WDI
WDO
RESET
VDD <
VPOR
Not Applicable
—
Undefined
Undefined
VPOR ≤
VDD < VIT-
Not Applicable
Ignored
High
Low
VDD ≥ VIT+
Disabled
Ignored
High
High
Enabled
tpulse
1 < tWD(min)
High
High
Enabled
tpulse
1 > tWD(max)
Low
High
VDD
WATCHDOG STATUS
WDI
WDO
RESET
VDD
WATCHDOG STATUS
WDI
WDO
RESET
VDDWATCHDOG STATUSWDI
WDO
WDO
RESET
RESET
VDD <
VPOR
Not Applicable
—
Undefined
Undefined
VPOR ≤
VDD < VIT-
Not Applicable
Ignored
High
Low
VDD ≥ VIT+
Disabled
Ignored
High
High
Enabled
tpulse
1 < tWD(min)
High
High
Enabled
tpulse
1 > tWD(max)
Low
High
VDD <
VPOR
Not Applicable
—
Undefined
Undefined
VDD <
VPOR
DDPORNot Applicable—UndefinedUndefined
VPOR ≤
VDD < VIT-
Not Applicable
Ignored
High
Low
VPOR ≤
VDD < VIT-
PORDDIT-Not ApplicableIgnoredHighLow
VDD ≥ VIT+
Disabled
Ignored
High
High
VDD ≥ VIT+
DDIT+DisabledIgnoredHighHigh
Enabled
tpulse
1 < tWD(min)
High
High
Enabledtpulse
1 < tWD(min)
pulse1WD(min)HighHigh
Enabled
tpulse
1 > tWD(max)
Low
High
Enabledtpulse
1 > tWD(max)
pulse1WD(max)LowHigh
Where tpulse is the time between falling edges on
WDI.
Where tpulse is the time between falling edges on
WDI.pulse
Application and Implementation
Information in the following applications sections is not part of the TI
component specification, and TI does not warrant its accuracy or completeness.
TI’s customers are responsible for determining suitability of components for
their purposes, as well as validating and testing their design implementation to
confirm system functionality.
Application Information
The following sections describe in detail proper device implementation, depending on the final application requirements.
Output Assert Delay
The TPS35 features two options
for setting the output assert delay (tD
): using a fixed timing and
programming the timing through an external
capacitor.
Factory-Programmed Output Assert Delay Timing
Fixed output assert delay timings are available
using pinout C and
D
and J. Using these timings enables a
high-precision, 10% accurate output assert delay timing.
Adjustable Capacitor Timing
The TPS35 also utilizes a
programmable output assert delay, using a precision current source to charge an
external capacitor upon device startup. The typical delay time resulting from a
given external capacitance on the CRST pin can be calculated by #GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-12, where tD
is the output assert delay
time in seconds and CCRST is the capacitance in microfarads.
tD
(sec) = 4.95 ×
106 × CCRST (F)
Note that to minimize the difference
between the calculated output assert delay time and the actual output assert delay
time, use a high-quality ceramic dielectric COG, X5R, or X7R capacitor and minimize
parasitic board capacitance around this pin. #GUID-D1D35606-1121-467A-A793-EC910F60F861/SBVS3011026 lists the output
assert delay time for ideal capacitor values.
Output Assert Delay Time for Common Ideal Capacitor Values
CCRST
OUTPUT
ASSERTDELAY TIME (tD
)
UNIT
MIN#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
TYP
MAX#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
10 nF
39.6
49.5
59.4
ms
100 nF
396
495
594
ms
1 μF
3960
4950
5940
ms
Minimum and maximum values are calculated using ideal capacitors.
Watchdog Timer Functionality
The TPS35 features two options
for setting the watchdog timer (tWD
): using a fixed timing and
programming the timing through an external capacitor.
Factory-Programmed Timing Options
Fixed watchdog timeout options are available
using pinout C and D
and J. Using these timings enables a
high-precision, 10% accurate watchdog timer tWD
.
Adjustable Capacitor Timing
Adjustable tWD
timing is achievable by connecting a capacitor to the
CWD pin. If this method is used, please consult
for
calculating typical tWD values using ideal capacitors. Capacitor
tolerances cause the actual device timing to vary such that the minimum of tWD
can decrease and the maximum of tWD
can increase by the capacitor tolerance. For the most
accurate timing, use ceramic capacitors with COG dielectric material.
Typical Applications
Design 1: Monitoring a Microcontroller Supply Voltage and Watchdog Timer
A
20231215
Replaced TPS35-Q1 with TPS35
Yes
The TPS35 features high-accuracy (1.2% maximum) voltage supervising along with
on-the-fly adjustable watchdog timing to monitor critical processing elements in
systems.
Microcontroller Supply and
Watchdog Monitoring Circuit
Design Requirements
Design Parameters
PARAMETER
DESIRED REQUIREMENT
DESIGN RESULT
Threshold Voltage
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Watchdog Timeout Period
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
RESET Delay
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Startup Delay
Minimum startup delay of 700 ms
Minimum startup delay of 900 ms
Output Logic
Open-drain
Open-drain
Maximum Device Current Consumption
20 μA
250 nA typical, 3 μA maximum
Detailed Design Procedure
Setting the Voltage Threshold
The negative-going threshold voltage, VIT-, is set by the device variant. #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB shows how to calculate the "Threshold Voltage" section of the orderable part number.
OPN "Threshold
Voltage" number = (VIT- - 1) /
0.05
In this example, the nominal supply voltage for
the microcontroller is 1.8 V. The minimum supply voltage is 10% lower than the
nominal supply voltage, or 1.62 V. Setting a 1.65 V threshold makes sure that the
device resets just before the supply voltage reaches the minimum allowed. Thus a
1.65 V threshold is chosen and, using #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB, the part number
is reduced to TPS35xx13xxxxxxx. Since the
hysteresis is 5% typical, the positive-going threshold voltage, VIT+, is
1.73 V.
Meeting the Watchdog Timeout Period
The watchdog timeout design requirement can be met
either by using a fixed-timeout version of the TPS35 or by
connecting a capacitor between the CWD pin and GND. The typical values can be met
with preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for
a list of fixed timeouts. If using the CWD feature, pinout A or B must be used;
please refer to
tWD Timer
for instructions
on how to program the timout period. The design requirement in this example is
tWD = 1.6 s. This is one of the fixed timeout options offered by
pinout C or D
or
J. Thus the possible variant
option is narrowed down to TPS35Cx13KAxDDFR.
Setting the Reset Delay
The reset delay requirement can be met either by
using a fixed-timeout version of the TPS35 or by connecting a
capacitor between the CRST pin and GND. The typical values can be met with
preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for a list of fixed timeouts. If using
the CRST feature, pinout A or B must be used; please refer to the Timing
Specifications for instructions on how to program the timout period. The
design requirement in this example is tD = 200 ms. Thus the possible
variant option is narrowed down to TPS35Cx13KAGDDFR.
Setting the Startup Delay and Output Topology
The startup delay and output topology are set by
the device variant. Please refer to Device Comparison for the possible
options. A minimum startup delay of 700 ms and
open-drain output are desired, thus Option D, 1 s
typical startup delay and open-drain active-low,
is selected. Thus the option suitable to meet
design requirements is TPS35CD13KAGDDFR.
Calculating the RESET Pullup Resistor
The TPS35 uses an open-drain configuration for the RESET output, as shown in .When the FET is off, the resistor pulls the drain of the transistor to VDD and when the FET is turned on, the FET pulls the output to ground, thus creating an effective resistor divider. The resistors in this divider must be chosen to make sure that VOL is below its maximum value. To choose the proper pullup resistor, there are three key specifications to keep in mind: the pullup voltage (VPU), the recommended maximum RESET pin current (IRST), and VOL. The maximum VOL is 0.3 V, meaning that the effective resistor divider created must be able to bring the voltage on the reset pin below 0.3 V with IRST kept below 2 mA for VDD ≥ 3 V and 500 μA for VDD = 1.5 V. For this example, with a VPU =VDD = 1.5 V, a resistor must be chosen to keep IRST below 500 μA because this value is the maximum consumption current allowed. To make sure this specification is met, a pullup resistor value of 10 kΩ was selected, which sinks a maximum of 180 μA when RESET is asserted.
Open-Drain RESET Configuration
Power Supply Recommendations
This device is designed to operate from
an input supply with a voltage range between 1.04 V and 6 V. An input supply capacitor is
not required for this device; however, if the input supply is noisy, then good analog
practice is to place a 0.1-µF capacitor between the VDD pin and the GND pin.
Layout
Layout Guidelines
Make sure that the connection to the VDD pin is
low impedance. Good analog design practice recommends placing a 0.1-µF ceramic
capacitor as near as possible to the VDD pin. If a capacitor is not connected to the
CRST pin, then minimize parasitic capacitance on this pin so the
RESET
delay time is not adversely affected.
Make sure that the connection
to the VDD pin is low impedance. Good analog design practice is to place a
0.1-µF ceramic capacitor as near as possible to the VDD pin.
Place CCRST
capacitor as close as possible to the CRST pin.
Place CCWD
capacitor as close as possible to the CWD pin.
Place the pullup resistor on
the
RESET
pin as close to the pin as
possible.
Layout Example
Typical
Layout for the Pinout C of TPS35
Application and Implementation
Information in the following applications sections is not part of the TI
component specification, and TI does not warrant its accuracy or completeness.
TI’s customers are responsible for determining suitability of components for
their purposes, as well as validating and testing their design implementation to
confirm system functionality.
Information in the following applications sections is not part of the TI
component specification, and TI does not warrant its accuracy or completeness.
TI’s customers are responsible for determining suitability of components for
their purposes, as well as validating and testing their design implementation to
confirm system functionality.
Information in the following applications sections is not part of the TI
component specification, and TI does not warrant its accuracy or completeness.
TI’s customers are responsible for determining suitability of components for
their purposes, as well as validating and testing their design implementation to
confirm system functionality.
Information in the following applications sections is not part of the TI
component specification, and TI does not warrant its accuracy or completeness.
TI’s customers are responsible for determining suitability of components for
their purposes, as well as validating and testing their design implementation to
confirm system functionality.
Information in the following applications sections is not part of the TI
component specification, and TI does not warrant its accuracy or completeness.
TI’s customers are responsible for determining suitability of components for
their purposes, as well as validating and testing their design implementation to
confirm system functionality.
Application Information
The following sections describe in detail proper device implementation, depending on the final application requirements.
Output Assert Delay
The TPS35 features two options
for setting the output assert delay (tD
): using a fixed timing and
programming the timing through an external
capacitor.
Factory-Programmed Output Assert Delay Timing
Fixed output assert delay timings are available
using pinout C and
D
and J. Using these timings enables a
high-precision, 10% accurate output assert delay timing.
Adjustable Capacitor Timing
The TPS35 also utilizes a
programmable output assert delay, using a precision current source to charge an
external capacitor upon device startup. The typical delay time resulting from a
given external capacitance on the CRST pin can be calculated by #GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-12, where tD
is the output assert delay
time in seconds and CCRST is the capacitance in microfarads.
tD
(sec) = 4.95 ×
106 × CCRST (F)
Note that to minimize the difference
between the calculated output assert delay time and the actual output assert delay
time, use a high-quality ceramic dielectric COG, X5R, or X7R capacitor and minimize
parasitic board capacitance around this pin. #GUID-D1D35606-1121-467A-A793-EC910F60F861/SBVS3011026 lists the output
assert delay time for ideal capacitor values.
Output Assert Delay Time for Common Ideal Capacitor Values
CCRST
OUTPUT
ASSERTDELAY TIME (tD
)
UNIT
MIN#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
TYP
MAX#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
10 nF
39.6
49.5
59.4
ms
100 nF
396
495
594
ms
1 μF
3960
4950
5940
ms
Minimum and maximum values are calculated using ideal capacitors.
Watchdog Timer Functionality
The TPS35 features two options
for setting the watchdog timer (tWD
): using a fixed timing and
programming the timing through an external capacitor.
Factory-Programmed Timing Options
Fixed watchdog timeout options are available
using pinout C and D
and J. Using these timings enables a
high-precision, 10% accurate watchdog timer tWD
.
Adjustable Capacitor Timing
Adjustable tWD
timing is achievable by connecting a capacitor to the
CWD pin. If this method is used, please consult
for
calculating typical tWD values using ideal capacitors. Capacitor
tolerances cause the actual device timing to vary such that the minimum of tWD
can decrease and the maximum of tWD
can increase by the capacitor tolerance. For the most
accurate timing, use ceramic capacitors with COG dielectric material.
Application Information
The following sections describe in detail proper device implementation, depending on the final application requirements.
The following sections describe in detail proper device implementation, depending on the final application requirements.
The following sections describe in detail proper device implementation, depending on the final application requirements.
Output Assert Delay
The TPS35 features two options
for setting the output assert delay (tD
): using a fixed timing and
programming the timing through an external
capacitor.
Factory-Programmed Output Assert Delay Timing
Fixed output assert delay timings are available
using pinout C and
D
and J. Using these timings enables a
high-precision, 10% accurate output assert delay timing.
Adjustable Capacitor Timing
The TPS35 also utilizes a
programmable output assert delay, using a precision current source to charge an
external capacitor upon device startup. The typical delay time resulting from a
given external capacitance on the CRST pin can be calculated by #GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-12, where tD
is the output assert delay
time in seconds and CCRST is the capacitance in microfarads.
tD
(sec) = 4.95 ×
106 × CCRST (F)
Note that to minimize the difference
between the calculated output assert delay time and the actual output assert delay
time, use a high-quality ceramic dielectric COG, X5R, or X7R capacitor and minimize
parasitic board capacitance around this pin. #GUID-D1D35606-1121-467A-A793-EC910F60F861/SBVS3011026 lists the output
assert delay time for ideal capacitor values.
Output Assert Delay Time for Common Ideal Capacitor Values
CCRST
OUTPUT
ASSERTDELAY TIME (tD
)
UNIT
MIN#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
TYP
MAX#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
10 nF
39.6
49.5
59.4
ms
100 nF
396
495
594
ms
1 μF
3960
4950
5940
ms
Minimum and maximum values are calculated using ideal capacitors.
Output Assert Delay
The TPS35 features two options
for setting the output assert delay (tD
): using a fixed timing and
programming the timing through an external
capacitor.
The TPS35 features two options
for setting the output assert delay (tD
): using a fixed timing and
programming the timing through an external
capacitor.
The TPS35 features two options
for setting the output assert delay (tD
): using a fixed timing and
programming the timing through an external
capacitor.TPS35tD
D
Factory-Programmed Output Assert Delay Timing
Fixed output assert delay timings are available
using pinout C and
D
and J. Using these timings enables a
high-precision, 10% accurate output assert delay timing.
Factory-Programmed Output Assert Delay Timing
Fixed output assert delay timings are available
using pinout C and
D
and J. Using these timings enables a
high-precision, 10% accurate output assert delay timing.
Fixed output assert delay timings are available
using pinout C and
D
and J. Using these timings enables a
high-precision, 10% accurate output assert delay timing.
Fixed output assert delay timings are available
using pinout C and
D
and J. Using these timings enables a
high-precision, 10% accurate output assert delay timing.and
Dand J
Adjustable Capacitor Timing
The TPS35 also utilizes a
programmable output assert delay, using a precision current source to charge an
external capacitor upon device startup. The typical delay time resulting from a
given external capacitance on the CRST pin can be calculated by #GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-12, where tD
is the output assert delay
time in seconds and CCRST is the capacitance in microfarads.
tD
(sec) = 4.95 ×
106 × CCRST (F)
Note that to minimize the difference
between the calculated output assert delay time and the actual output assert delay
time, use a high-quality ceramic dielectric COG, X5R, or X7R capacitor and minimize
parasitic board capacitance around this pin. #GUID-D1D35606-1121-467A-A793-EC910F60F861/SBVS3011026 lists the output
assert delay time for ideal capacitor values.
Output Assert Delay Time for Common Ideal Capacitor Values
CCRST
OUTPUT
ASSERTDELAY TIME (tD
)
UNIT
MIN#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
TYP
MAX#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
10 nF
39.6
49.5
59.4
ms
100 nF
396
495
594
ms
1 μF
3960
4950
5940
ms
Minimum and maximum values are calculated using ideal capacitors.
Adjustable Capacitor Timing
The TPS35 also utilizes a
programmable output assert delay, using a precision current source to charge an
external capacitor upon device startup. The typical delay time resulting from a
given external capacitance on the CRST pin can be calculated by #GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-12, where tD
is the output assert delay
time in seconds and CCRST is the capacitance in microfarads.
tD
(sec) = 4.95 ×
106 × CCRST (F)
Note that to minimize the difference
between the calculated output assert delay time and the actual output assert delay
time, use a high-quality ceramic dielectric COG, X5R, or X7R capacitor and minimize
parasitic board capacitance around this pin. #GUID-D1D35606-1121-467A-A793-EC910F60F861/SBVS3011026 lists the output
assert delay time for ideal capacitor values.
Output Assert Delay Time for Common Ideal Capacitor Values
CCRST
OUTPUT
ASSERTDELAY TIME (tD
)
UNIT
MIN#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
TYP
MAX#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
10 nF
39.6
49.5
59.4
ms
100 nF
396
495
594
ms
1 μF
3960
4950
5940
ms
Minimum and maximum values are calculated using ideal capacitors.
The TPS35 also utilizes a
programmable output assert delay, using a precision current source to charge an
external capacitor upon device startup. The typical delay time resulting from a
given external capacitance on the CRST pin can be calculated by #GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-12, where tD
is the output assert delay
time in seconds and CCRST is the capacitance in microfarads.
tD
(sec) = 4.95 ×
106 × CCRST (F)
Note that to minimize the difference
between the calculated output assert delay time and the actual output assert delay
time, use a high-quality ceramic dielectric COG, X5R, or X7R capacitor and minimize
parasitic board capacitance around this pin. #GUID-D1D35606-1121-467A-A793-EC910F60F861/SBVS3011026 lists the output
assert delay time for ideal capacitor values.
Output Assert Delay Time for Common Ideal Capacitor Values
CCRST
OUTPUT
ASSERTDELAY TIME (tD
)
UNIT
MIN#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
TYP
MAX#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
10 nF
39.6
49.5
59.4
ms
100 nF
396
495
594
ms
1 μF
3960
4950
5940
ms
Minimum and maximum values are calculated using ideal capacitors.
The TPS35 also utilizes a
programmable output assert delay, using a precision current source to charge an
external capacitor upon device startup. The typical delay time resulting from a
given external capacitance on the CRST pin can be calculated by #GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-12, where tD
is the output assert delay
time in seconds and CCRST is the capacitance in microfarads.TPS35#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-12tD
DCRST
tD
(sec) = 4.95 ×
106 × CCRST (F)tD
D6CRSTNote that to minimize the difference
between the calculated output assert delay time and the actual output assert delay
time, use a high-quality ceramic dielectric COG, X5R, or X7R capacitor and minimize
parasitic board capacitance around this pin. #GUID-D1D35606-1121-467A-A793-EC910F60F861/SBVS3011026 lists the output
assert delay time for ideal capacitor values.#GUID-D1D35606-1121-467A-A793-EC910F60F861/SBVS3011026
Output Assert Delay Time for Common Ideal Capacitor Values
CCRST
OUTPUT
ASSERTDELAY TIME (tD
)
UNIT
MIN#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
TYP
MAX#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
10 nF
39.6
49.5
59.4
ms
100 nF
396
495
594
ms
1 μF
3960
4950
5940
ms
Output Assert Delay Time for Common Ideal Capacitor Values
CCRST
OUTPUT
ASSERTDELAY TIME (tD
)
UNIT
MIN#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
TYP
MAX#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
10 nF
39.6
49.5
59.4
ms
100 nF
396
495
594
ms
1 μF
3960
4950
5940
ms
CCRST
OUTPUT
ASSERTDELAY TIME (tD
)
UNIT
MIN#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
TYP
MAX#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
CCRST
OUTPUT
ASSERTDELAY TIME (tD
)
UNIT
CCRST
CRST
OUTPUT
ASSERTDELAY TIME (tD
)OUTPUT
ASSERTtD
DUNIT
MIN#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
TYP
MAX#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
MIN#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39TYPMAX#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
#GUID-D1D35606-1121-467A-A793-EC910F60F861/T4523365-39
10 nF
39.6
49.5
59.4
ms
100 nF
396
495
594
ms
1 μF
3960
4950
5940
ms
10 nF
39.6
49.5
59.4
ms
10 nF
39.6
39.649.5
59.4
59.4ms
100 nF
396
495
594
ms
100 nF
396
396
495
495
594
594ms
1 μF
3960
4950
5940
ms
1 μF
3960
3960
4950
4950
5940
5940ms
Minimum and maximum values are calculated using ideal capacitors.
Minimum and maximum values are calculated using ideal capacitors.
Watchdog Timer Functionality
The TPS35 features two options
for setting the watchdog timer (tWD
): using a fixed timing and
programming the timing through an external capacitor.
Factory-Programmed Timing Options
Fixed watchdog timeout options are available
using pinout C and D
and J. Using these timings enables a
high-precision, 10% accurate watchdog timer tWD
.
Adjustable Capacitor Timing
Adjustable tWD
timing is achievable by connecting a capacitor to the
CWD pin. If this method is used, please consult
for
calculating typical tWD values using ideal capacitors. Capacitor
tolerances cause the actual device timing to vary such that the minimum of tWD
can decrease and the maximum of tWD
can increase by the capacitor tolerance. For the most
accurate timing, use ceramic capacitors with COG dielectric material.
Watchdog Timer FunctionalityTimer
The TPS35 features two options
for setting the watchdog timer (tWD
): using a fixed timing and
programming the timing through an external capacitor.
The TPS35 features two options
for setting the watchdog timer (tWD
): using a fixed timing and
programming the timing through an external capacitor.
The TPS35 features two options
for setting the watchdog timer (tWD
): using a fixed timing and
programming the timing through an external capacitor.TPS35tWD
WD
Factory-Programmed Timing Options
Fixed watchdog timeout options are available
using pinout C and D
and J. Using these timings enables a
high-precision, 10% accurate watchdog timer tWD
.
Factory-Programmed Timing Options
Fixed watchdog timeout options are available
using pinout C and D
and J. Using these timings enables a
high-precision, 10% accurate watchdog timer tWD
.
Fixed watchdog timeout options are available
using pinout C and D
and J. Using these timings enables a
high-precision, 10% accurate watchdog timer tWD
.
Fixed watchdog timeout options are available
using pinout C and D
and J. Using these timings enables a
high-precision, 10% accurate watchdog timer tWD
. and D and JtWD
WD
Adjustable Capacitor Timing
Adjustable tWD
timing is achievable by connecting a capacitor to the
CWD pin. If this method is used, please consult
for
calculating typical tWD values using ideal capacitors. Capacitor
tolerances cause the actual device timing to vary such that the minimum of tWD
can decrease and the maximum of tWD
can increase by the capacitor tolerance. For the most
accurate timing, use ceramic capacitors with COG dielectric material.
Adjustable Capacitor Timing
Adjustable tWD
timing is achievable by connecting a capacitor to the
CWD pin. If this method is used, please consult
for
calculating typical tWD values using ideal capacitors. Capacitor
tolerances cause the actual device timing to vary such that the minimum of tWD
can decrease and the maximum of tWD
can increase by the capacitor tolerance. For the most
accurate timing, use ceramic capacitors with COG dielectric material.
Adjustable tWD
timing is achievable by connecting a capacitor to the
CWD pin. If this method is used, please consult
for
calculating typical tWD values using ideal capacitors. Capacitor
tolerances cause the actual device timing to vary such that the minimum of tWD
can decrease and the maximum of tWD
can increase by the capacitor tolerance. For the most
accurate timing, use ceramic capacitors with COG dielectric material.
Adjustable tWD
timing is achievable by connecting a capacitor to the
CWD pin. If this method is used, please consult
for
calculating typical tWD values using ideal capacitors. Capacitor
tolerances cause the actual device timing to vary such that the minimum of tWD
can decrease and the maximum of tWD
can increase by the capacitor tolerance. For the most
accurate timing, use ceramic capacitors with COG dielectric material.tWD
WD
for
calculating typical tWD values using ideal capacitors.WDtWD
WDtWD
WD
Typical Applications
Design 1: Monitoring a Microcontroller Supply Voltage and Watchdog Timer
A
20231215
Replaced TPS35-Q1 with TPS35
Yes
The TPS35 features high-accuracy (1.2% maximum) voltage supervising along with
on-the-fly adjustable watchdog timing to monitor critical processing elements in
systems.
Microcontroller Supply and
Watchdog Monitoring Circuit
Design Requirements
Design Parameters
PARAMETER
DESIRED REQUIREMENT
DESIGN RESULT
Threshold Voltage
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Watchdog Timeout Period
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
RESET Delay
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Startup Delay
Minimum startup delay of 700 ms
Minimum startup delay of 900 ms
Output Logic
Open-drain
Open-drain
Maximum Device Current Consumption
20 μA
250 nA typical, 3 μA maximum
Detailed Design Procedure
Setting the Voltage Threshold
The negative-going threshold voltage, VIT-, is set by the device variant. #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB shows how to calculate the "Threshold Voltage" section of the orderable part number.
OPN "Threshold
Voltage" number = (VIT- - 1) /
0.05
In this example, the nominal supply voltage for
the microcontroller is 1.8 V. The minimum supply voltage is 10% lower than the
nominal supply voltage, or 1.62 V. Setting a 1.65 V threshold makes sure that the
device resets just before the supply voltage reaches the minimum allowed. Thus a
1.65 V threshold is chosen and, using #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB, the part number
is reduced to TPS35xx13xxxxxxx. Since the
hysteresis is 5% typical, the positive-going threshold voltage, VIT+, is
1.73 V.
Meeting the Watchdog Timeout Period
The watchdog timeout design requirement can be met
either by using a fixed-timeout version of the TPS35 or by
connecting a capacitor between the CWD pin and GND. The typical values can be met
with preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for
a list of fixed timeouts. If using the CWD feature, pinout A or B must be used;
please refer to
tWD Timer
for instructions
on how to program the timout period. The design requirement in this example is
tWD = 1.6 s. This is one of the fixed timeout options offered by
pinout C or D
or
J. Thus the possible variant
option is narrowed down to TPS35Cx13KAxDDFR.
Setting the Reset Delay
The reset delay requirement can be met either by
using a fixed-timeout version of the TPS35 or by connecting a
capacitor between the CRST pin and GND. The typical values can be met with
preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for a list of fixed timeouts. If using
the CRST feature, pinout A or B must be used; please refer to the Timing
Specifications for instructions on how to program the timout period. The
design requirement in this example is tD = 200 ms. Thus the possible
variant option is narrowed down to TPS35Cx13KAGDDFR.
Setting the Startup Delay and Output Topology
The startup delay and output topology are set by
the device variant. Please refer to Device Comparison for the possible
options. A minimum startup delay of 700 ms and
open-drain output are desired, thus Option D, 1 s
typical startup delay and open-drain active-low,
is selected. Thus the option suitable to meet
design requirements is TPS35CD13KAGDDFR.
Calculating the RESET Pullup Resistor
The TPS35 uses an open-drain configuration for the RESET output, as shown in .When the FET is off, the resistor pulls the drain of the transistor to VDD and when the FET is turned on, the FET pulls the output to ground, thus creating an effective resistor divider. The resistors in this divider must be chosen to make sure that VOL is below its maximum value. To choose the proper pullup resistor, there are three key specifications to keep in mind: the pullup voltage (VPU), the recommended maximum RESET pin current (IRST), and VOL. The maximum VOL is 0.3 V, meaning that the effective resistor divider created must be able to bring the voltage on the reset pin below 0.3 V with IRST kept below 2 mA for VDD ≥ 3 V and 500 μA for VDD = 1.5 V. For this example, with a VPU =VDD = 1.5 V, a resistor must be chosen to keep IRST below 500 μA because this value is the maximum consumption current allowed. To make sure this specification is met, a pullup resistor value of 10 kΩ was selected, which sinks a maximum of 180 μA when RESET is asserted.
Open-Drain RESET Configuration
Typical Applications
Design 1: Monitoring a Microcontroller Supply Voltage and Watchdog Timer
A
20231215
Replaced TPS35-Q1 with TPS35
Yes
The TPS35 features high-accuracy (1.2% maximum) voltage supervising along with
on-the-fly adjustable watchdog timing to monitor critical processing elements in
systems.
Microcontroller Supply and
Watchdog Monitoring Circuit
Design Requirements
Design Parameters
PARAMETER
DESIRED REQUIREMENT
DESIGN RESULT
Threshold Voltage
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Watchdog Timeout Period
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
RESET Delay
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Startup Delay
Minimum startup delay of 700 ms
Minimum startup delay of 900 ms
Output Logic
Open-drain
Open-drain
Maximum Device Current Consumption
20 μA
250 nA typical, 3 μA maximum
Detailed Design Procedure
Setting the Voltage Threshold
The negative-going threshold voltage, VIT-, is set by the device variant. #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB shows how to calculate the "Threshold Voltage" section of the orderable part number.
OPN "Threshold
Voltage" number = (VIT- - 1) /
0.05
In this example, the nominal supply voltage for
the microcontroller is 1.8 V. The minimum supply voltage is 10% lower than the
nominal supply voltage, or 1.62 V. Setting a 1.65 V threshold makes sure that the
device resets just before the supply voltage reaches the minimum allowed. Thus a
1.65 V threshold is chosen and, using #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB, the part number
is reduced to TPS35xx13xxxxxxx. Since the
hysteresis is 5% typical, the positive-going threshold voltage, VIT+, is
1.73 V.
Meeting the Watchdog Timeout Period
The watchdog timeout design requirement can be met
either by using a fixed-timeout version of the TPS35 or by
connecting a capacitor between the CWD pin and GND. The typical values can be met
with preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for
a list of fixed timeouts. If using the CWD feature, pinout A or B must be used;
please refer to
tWD Timer
for instructions
on how to program the timout period. The design requirement in this example is
tWD = 1.6 s. This is one of the fixed timeout options offered by
pinout C or D
or
J. Thus the possible variant
option is narrowed down to TPS35Cx13KAxDDFR.
Setting the Reset Delay
The reset delay requirement can be met either by
using a fixed-timeout version of the TPS35 or by connecting a
capacitor between the CRST pin and GND. The typical values can be met with
preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for a list of fixed timeouts. If using
the CRST feature, pinout A or B must be used; please refer to the Timing
Specifications for instructions on how to program the timout period. The
design requirement in this example is tD = 200 ms. Thus the possible
variant option is narrowed down to TPS35Cx13KAGDDFR.
Setting the Startup Delay and Output Topology
The startup delay and output topology are set by
the device variant. Please refer to Device Comparison for the possible
options. A minimum startup delay of 700 ms and
open-drain output are desired, thus Option D, 1 s
typical startup delay and open-drain active-low,
is selected. Thus the option suitable to meet
design requirements is TPS35CD13KAGDDFR.
Calculating the RESET Pullup Resistor
The TPS35 uses an open-drain configuration for the RESET output, as shown in .When the FET is off, the resistor pulls the drain of the transistor to VDD and when the FET is turned on, the FET pulls the output to ground, thus creating an effective resistor divider. The resistors in this divider must be chosen to make sure that VOL is below its maximum value. To choose the proper pullup resistor, there are three key specifications to keep in mind: the pullup voltage (VPU), the recommended maximum RESET pin current (IRST), and VOL. The maximum VOL is 0.3 V, meaning that the effective resistor divider created must be able to bring the voltage on the reset pin below 0.3 V with IRST kept below 2 mA for VDD ≥ 3 V and 500 μA for VDD = 1.5 V. For this example, with a VPU =VDD = 1.5 V, a resistor must be chosen to keep IRST below 500 μA because this value is the maximum consumption current allowed. To make sure this specification is met, a pullup resistor value of 10 kΩ was selected, which sinks a maximum of 180 μA when RESET is asserted.
Open-Drain RESET Configuration
Design 1: Monitoring a Microcontroller Supply Voltage and Watchdog Timer
A
20231215
Replaced TPS35-Q1 with TPS35
Yes
A
20231215
Replaced TPS35-Q1 with TPS35
Yes
A
20231215
Replaced TPS35-Q1 with TPS35
Yes
A20231215Replaced TPS35-Q1 with TPS35Yes
The TPS35 features high-accuracy (1.2% maximum) voltage supervising along with
on-the-fly adjustable watchdog timing to monitor critical processing elements in
systems.
Microcontroller Supply and
Watchdog Monitoring Circuit
The TPS35 features high-accuracy (1.2% maximum) voltage supervising along with
on-the-fly adjustable watchdog timing to monitor critical processing elements in
systems.
Microcontroller Supply and
Watchdog Monitoring Circuit
The TPS35 features high-accuracy (1.2% maximum) voltage supervising along with
on-the-fly adjustable watchdog timing to monitor critical processing elements in
systems.
Microcontroller Supply and
Watchdog Monitoring Circuit
Microcontroller Supply and
Watchdog Monitoring Circuit
Design Requirements
Design Parameters
PARAMETER
DESIRED REQUIREMENT
DESIGN RESULT
Threshold Voltage
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Watchdog Timeout Period
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
RESET Delay
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Startup Delay
Minimum startup delay of 700 ms
Minimum startup delay of 900 ms
Output Logic
Open-drain
Open-drain
Maximum Device Current Consumption
20 μA
250 nA typical, 3 μA maximum
Design Requirements
Design Parameters
PARAMETER
DESIRED REQUIREMENT
DESIGN RESULT
Threshold Voltage
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Watchdog Timeout Period
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
RESET Delay
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Startup Delay
Minimum startup delay of 700 ms
Minimum startup delay of 900 ms
Output Logic
Open-drain
Open-drain
Maximum Device Current Consumption
20 μA
250 nA typical, 3 μA maximum
Design Parameters
PARAMETER
DESIRED REQUIREMENT
DESIGN RESULT
Threshold Voltage
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Watchdog Timeout Period
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
RESET Delay
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Startup Delay
Minimum startup delay of 700 ms
Minimum startup delay of 900 ms
Output Logic
Open-drain
Open-drain
Maximum Device Current Consumption
20 μA
250 nA typical, 3 μA maximum
Design Parameters
PARAMETER
DESIRED REQUIREMENT
DESIGN RESULT
Threshold Voltage
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Watchdog Timeout Period
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
RESET Delay
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Startup Delay
Minimum startup delay of 700 ms
Minimum startup delay of 900 ms
Output Logic
Open-drain
Open-drain
Maximum Device Current Consumption
20 μA
250 nA typical, 3 μA maximum
Design Parameters
PARAMETER
DESIRED REQUIREMENT
DESIGN RESULT
Threshold Voltage
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Watchdog Timeout Period
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
RESET Delay
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Startup Delay
Minimum startup delay of 700 ms
Minimum startup delay of 900 ms
Output Logic
Open-drain
Open-drain
Maximum Device Current Consumption
20 μA
250 nA typical, 3 μA maximum
PARAMETER
DESIRED REQUIREMENT
DESIGN RESULT
PARAMETER
DESIRED REQUIREMENT
DESIGN RESULT
PARAMETER
DESIRED REQUIREMENT
DESIRED REQUIREMENT
DESIGN RESULT
DESIGN RESULT
Threshold Voltage
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Watchdog Timeout Period
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
RESET Delay
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Startup Delay
Minimum startup delay of 700 ms
Minimum startup delay of 900 ms
Output Logic
Open-drain
Open-drain
Maximum Device Current Consumption
20 μA
250 nA typical, 3 μA maximum
Threshold Voltage
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Threshold Voltage
Threshold Voltage
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Typical threshold voltage of 1.65 V
Watchdog Timeout Period
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
Watchdog Timeout Period
Watchdog Timeout Period
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
Typical timeout period of 1.6 s
RESET Delay
Typical reset delay of 200 ms
Typical reset delay of 200 ms
RESET Delay
RESET Delay
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Typical reset delay of 200 ms
Startup Delay
Minimum startup delay of 700 ms
Minimum startup delay of 900 ms
Startup Delay
Startup Delay
Minimum startup delay of 700 ms
Minimum startup delay of 700 ms
Minimum startup delay of 900 ms
Minimum startup delay of 900 ms
Output Logic
Open-drain
Open-drain
Output Logic
Output Logic
Open-drain
Open-drain
Open-drain
Open-drain
Maximum Device Current Consumption
20 μA
250 nA typical, 3 μA maximum
Maximum Device Current Consumption
Maximum Device Current Consumption
20 μA
20 μA
250 nA typical, 3 μA maximum
250 nA typical, 3 μA maximum
Detailed Design Procedure
Setting the Voltage Threshold
The negative-going threshold voltage, VIT-, is set by the device variant. #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB shows how to calculate the "Threshold Voltage" section of the orderable part number.
OPN "Threshold
Voltage" number = (VIT- - 1) /
0.05
In this example, the nominal supply voltage for
the microcontroller is 1.8 V. The minimum supply voltage is 10% lower than the
nominal supply voltage, or 1.62 V. Setting a 1.65 V threshold makes sure that the
device resets just before the supply voltage reaches the minimum allowed. Thus a
1.65 V threshold is chosen and, using #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB, the part number
is reduced to TPS35xx13xxxxxxx. Since the
hysteresis is 5% typical, the positive-going threshold voltage, VIT+, is
1.73 V.
Meeting the Watchdog Timeout Period
The watchdog timeout design requirement can be met
either by using a fixed-timeout version of the TPS35 or by
connecting a capacitor between the CWD pin and GND. The typical values can be met
with preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for
a list of fixed timeouts. If using the CWD feature, pinout A or B must be used;
please refer to
tWD Timer
for instructions
on how to program the timout period. The design requirement in this example is
tWD = 1.6 s. This is one of the fixed timeout options offered by
pinout C or D
or
J. Thus the possible variant
option is narrowed down to TPS35Cx13KAxDDFR.
Setting the Reset Delay
The reset delay requirement can be met either by
using a fixed-timeout version of the TPS35 or by connecting a
capacitor between the CRST pin and GND. The typical values can be met with
preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for a list of fixed timeouts. If using
the CRST feature, pinout A or B must be used; please refer to the Timing
Specifications for instructions on how to program the timout period. The
design requirement in this example is tD = 200 ms. Thus the possible
variant option is narrowed down to TPS35Cx13KAGDDFR.
Setting the Startup Delay and Output Topology
The startup delay and output topology are set by
the device variant. Please refer to Device Comparison for the possible
options. A minimum startup delay of 700 ms and
open-drain output are desired, thus Option D, 1 s
typical startup delay and open-drain active-low,
is selected. Thus the option suitable to meet
design requirements is TPS35CD13KAGDDFR.
Calculating the RESET Pullup Resistor
The TPS35 uses an open-drain configuration for the RESET output, as shown in .When the FET is off, the resistor pulls the drain of the transistor to VDD and when the FET is turned on, the FET pulls the output to ground, thus creating an effective resistor divider. The resistors in this divider must be chosen to make sure that VOL is below its maximum value. To choose the proper pullup resistor, there are three key specifications to keep in mind: the pullup voltage (VPU), the recommended maximum RESET pin current (IRST), and VOL. The maximum VOL is 0.3 V, meaning that the effective resistor divider created must be able to bring the voltage on the reset pin below 0.3 V with IRST kept below 2 mA for VDD ≥ 3 V and 500 μA for VDD = 1.5 V. For this example, with a VPU =VDD = 1.5 V, a resistor must be chosen to keep IRST below 500 μA because this value is the maximum consumption current allowed. To make sure this specification is met, a pullup resistor value of 10 kΩ was selected, which sinks a maximum of 180 μA when RESET is asserted.
Open-Drain RESET Configuration
Detailed Design Procedure
Setting the Voltage Threshold
The negative-going threshold voltage, VIT-, is set by the device variant. #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB shows how to calculate the "Threshold Voltage" section of the orderable part number.
OPN "Threshold
Voltage" number = (VIT- - 1) /
0.05
In this example, the nominal supply voltage for
the microcontroller is 1.8 V. The minimum supply voltage is 10% lower than the
nominal supply voltage, or 1.62 V. Setting a 1.65 V threshold makes sure that the
device resets just before the supply voltage reaches the minimum allowed. Thus a
1.65 V threshold is chosen and, using #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB, the part number
is reduced to TPS35xx13xxxxxxx. Since the
hysteresis is 5% typical, the positive-going threshold voltage, VIT+, is
1.73 V.
Setting the Voltage Threshold
The negative-going threshold voltage, VIT-, is set by the device variant. #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB shows how to calculate the "Threshold Voltage" section of the orderable part number.
OPN "Threshold
Voltage" number = (VIT- - 1) /
0.05
In this example, the nominal supply voltage for
the microcontroller is 1.8 V. The minimum supply voltage is 10% lower than the
nominal supply voltage, or 1.62 V. Setting a 1.65 V threshold makes sure that the
device resets just before the supply voltage reaches the minimum allowed. Thus a
1.65 V threshold is chosen and, using #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB, the part number
is reduced to TPS35xx13xxxxxxx. Since the
hysteresis is 5% typical, the positive-going threshold voltage, VIT+, is
1.73 V.
The negative-going threshold voltage, VIT-, is set by the device variant. #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB shows how to calculate the "Threshold Voltage" section of the orderable part number.
OPN "Threshold
Voltage" number = (VIT- - 1) /
0.05
In this example, the nominal supply voltage for
the microcontroller is 1.8 V. The minimum supply voltage is 10% lower than the
nominal supply voltage, or 1.62 V. Setting a 1.65 V threshold makes sure that the
device resets just before the supply voltage reaches the minimum allowed. Thus a
1.65 V threshold is chosen and, using #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB, the part number
is reduced to TPS35xx13xxxxxxx. Since the
hysteresis is 5% typical, the positive-going threshold voltage, VIT+, is
1.73 V.
The negative-going threshold voltage, VIT-, is set by the device variant. #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB shows how to calculate the "Threshold Voltage" section of the orderable part number.IT-#GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB
OPN "Threshold
Voltage" number = (VIT- - 1) /
0.05
OPN "Threshold
Voltage" number = (VIT- - 1) /
0.05IT-In this example, the nominal supply voltage for
the microcontroller is 1.8 V. The minimum supply voltage is 10% lower than the
nominal supply voltage, or 1.62 V. Setting a 1.65 V threshold makes sure that the
device resets just before the supply voltage reaches the minimum allowed. Thus a
1.65 V threshold is chosen and, using #GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTB, the part number
is reduced to TPS35xx13xxxxxxx. Since the
hysteresis is 5% typical, the positive-going threshold voltage, VIT+, is
1.73 V.#GUID-D42EE85E-B904-4EDB-8CC9-1CD90C625CBE/EQUATION-BLOCK_XV1_5Z1_YTBIT+
Meeting the Watchdog Timeout Period
The watchdog timeout design requirement can be met
either by using a fixed-timeout version of the TPS35 or by
connecting a capacitor between the CWD pin and GND. The typical values can be met
with preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for
a list of fixed timeouts. If using the CWD feature, pinout A or B must be used;
please refer to
tWD Timer
for instructions
on how to program the timout period. The design requirement in this example is
tWD = 1.6 s. This is one of the fixed timeout options offered by
pinout C or D
or
J. Thus the possible variant
option is narrowed down to TPS35Cx13KAxDDFR.
Meeting the Watchdog Timeout Period
The watchdog timeout design requirement can be met
either by using a fixed-timeout version of the TPS35 or by
connecting a capacitor between the CWD pin and GND. The typical values can be met
with preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for
a list of fixed timeouts. If using the CWD feature, pinout A or B must be used;
please refer to
tWD Timer
for instructions
on how to program the timout period. The design requirement in this example is
tWD = 1.6 s. This is one of the fixed timeout options offered by
pinout C or D
or
J. Thus the possible variant
option is narrowed down to TPS35Cx13KAxDDFR.
The watchdog timeout design requirement can be met
either by using a fixed-timeout version of the TPS35 or by
connecting a capacitor between the CWD pin and GND. The typical values can be met
with preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for
a list of fixed timeouts. If using the CWD feature, pinout A or B must be used;
please refer to
tWD Timer
for instructions
on how to program the timout period. The design requirement in this example is
tWD = 1.6 s. This is one of the fixed timeout options offered by
pinout C or D
or
J. Thus the possible variant
option is narrowed down to TPS35Cx13KAxDDFR.
The watchdog timeout design requirement can be met
either by using a fixed-timeout version of the TPS35 or by
connecting a capacitor between the CWD pin and GND. The typical values can be met
with preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for
a list of fixed timeouts. If using the CWD feature, pinout A or B must be used;
please refer to
tWD Timer
for instructions
on how to program the timout period. The design requirement in this example is
tWD = 1.6 s. This is one of the fixed timeout options offered by
pinout C or D
or
J. Thus the possible variant
option is narrowed down to TPS35Cx13KAxDDFR.TPS35Timing Requirements
tWD Timer
tWD TimerWDWD or D or
JTPS35Cx13KAxDDFR
Setting the Reset Delay
The reset delay requirement can be met either by
using a fixed-timeout version of the TPS35 or by connecting a
capacitor between the CRST pin and GND. The typical values can be met with
preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for a list of fixed timeouts. If using
the CRST feature, pinout A or B must be used; please refer to the Timing
Specifications for instructions on how to program the timout period. The
design requirement in this example is tD = 200 ms. Thus the possible
variant option is narrowed down to TPS35Cx13KAGDDFR.
Setting the Reset Delay
The reset delay requirement can be met either by
using a fixed-timeout version of the TPS35 or by connecting a
capacitor between the CRST pin and GND. The typical values can be met with
preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for a list of fixed timeouts. If using
the CRST feature, pinout A or B must be used; please refer to the Timing
Specifications for instructions on how to program the timout period. The
design requirement in this example is tD = 200 ms. Thus the possible
variant option is narrowed down to TPS35Cx13KAGDDFR.
The reset delay requirement can be met either by
using a fixed-timeout version of the TPS35 or by connecting a
capacitor between the CRST pin and GND. The typical values can be met with
preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for a list of fixed timeouts. If using
the CRST feature, pinout A or B must be used; please refer to the Timing
Specifications for instructions on how to program the timout period. The
design requirement in this example is tD = 200 ms. Thus the possible
variant option is narrowed down to TPS35Cx13KAGDDFR.
The reset delay requirement can be met either by
using a fixed-timeout version of the TPS35 or by connecting a
capacitor between the CRST pin and GND. The typical values can be met with
preprogrammed fixed time options, hence a pinout offering fixed time options is
selected. Please see the Timing Requirements for a list of fixed timeouts. If using
the CRST feature, pinout A or B must be used; please refer to the Timing
Specifications for instructions on how to program the timout period. The
design requirement in this example is tD = 200 ms. Thus the possible
variant option is narrowed down to TPS35Cx13KAGDDFR.TPS35Timing
SpecificationsDTPS35Cx13KAGDDFR
Setting the Startup Delay and Output Topology
The startup delay and output topology are set by
the device variant. Please refer to Device Comparison for the possible
options. A minimum startup delay of 700 ms and
open-drain output are desired, thus Option D, 1 s
typical startup delay and open-drain active-low,
is selected. Thus the option suitable to meet
design requirements is TPS35CD13KAGDDFR.
Setting the Startup Delay and Output Topology
The startup delay and output topology are set by
the device variant. Please refer to Device Comparison for the possible
options. A minimum startup delay of 700 ms and
open-drain output are desired, thus Option D, 1 s
typical startup delay and open-drain active-low,
is selected. Thus the option suitable to meet
design requirements is TPS35CD13KAGDDFR.
The startup delay and output topology are set by
the device variant. Please refer to Device Comparison for the possible
options. A minimum startup delay of 700 ms and
open-drain output are desired, thus Option D, 1 s
typical startup delay and open-drain active-low,
is selected. Thus the option suitable to meet
design requirements is TPS35CD13KAGDDFR.
The startup delay and output topology are set by
the device variant. Please refer to Device Comparison for the possible
options. A minimum startup delay of 700 ms and
open-drain output are desired, thus Option D, 1 s
typical startup delay and open-drain active-low,
is selected. Thus the option suitable to meet
design requirements is TPS35CD13KAGDDFR.Device ComparisonTPS35CD13KAGDDFR
Calculating the RESET Pullup Resistor
The TPS35 uses an open-drain configuration for the RESET output, as shown in .When the FET is off, the resistor pulls the drain of the transistor to VDD and when the FET is turned on, the FET pulls the output to ground, thus creating an effective resistor divider. The resistors in this divider must be chosen to make sure that VOL is below its maximum value. To choose the proper pullup resistor, there are three key specifications to keep in mind: the pullup voltage (VPU), the recommended maximum RESET pin current (IRST), and VOL. The maximum VOL is 0.3 V, meaning that the effective resistor divider created must be able to bring the voltage on the reset pin below 0.3 V with IRST kept below 2 mA for VDD ≥ 3 V and 500 μA for VDD = 1.5 V. For this example, with a VPU =VDD = 1.5 V, a resistor must be chosen to keep IRST below 500 μA because this value is the maximum consumption current allowed. To make sure this specification is met, a pullup resistor value of 10 kΩ was selected, which sinks a maximum of 180 μA when RESET is asserted.
Open-Drain RESET Configuration
Calculating the RESET Pullup ResistorRESET
The TPS35 uses an open-drain configuration for the RESET output, as shown in .When the FET is off, the resistor pulls the drain of the transistor to VDD and when the FET is turned on, the FET pulls the output to ground, thus creating an effective resistor divider. The resistors in this divider must be chosen to make sure that VOL is below its maximum value. To choose the proper pullup resistor, there are three key specifications to keep in mind: the pullup voltage (VPU), the recommended maximum RESET pin current (IRST), and VOL. The maximum VOL is 0.3 V, meaning that the effective resistor divider created must be able to bring the voltage on the reset pin below 0.3 V with IRST kept below 2 mA for VDD ≥ 3 V and 500 μA for VDD = 1.5 V. For this example, with a VPU =VDD = 1.5 V, a resistor must be chosen to keep IRST below 500 μA because this value is the maximum consumption current allowed. To make sure this specification is met, a pullup resistor value of 10 kΩ was selected, which sinks a maximum of 180 μA when RESET is asserted.
Open-Drain RESET Configuration
The TPS35 uses an open-drain configuration for the RESET output, as shown in .When the FET is off, the resistor pulls the drain of the transistor to VDD and when the FET is turned on, the FET pulls the output to ground, thus creating an effective resistor divider. The resistors in this divider must be chosen to make sure that VOL is below its maximum value. To choose the proper pullup resistor, there are three key specifications to keep in mind: the pullup voltage (VPU), the recommended maximum RESET pin current (IRST), and VOL. The maximum VOL is 0.3 V, meaning that the effective resistor divider created must be able to bring the voltage on the reset pin below 0.3 V with IRST kept below 2 mA for VDD ≥ 3 V and 500 μA for VDD = 1.5 V. For this example, with a VPU =VDD = 1.5 V, a resistor must be chosen to keep IRST below 500 μA because this value is the maximum consumption current allowed. To make sure this specification is met, a pullup resistor value of 10 kΩ was selected, which sinks a maximum of 180 μA when RESET is asserted.
Open-Drain RESET Configuration
The TPS35 uses an open-drain configuration for the RESET output, as shown in .When the FET is off, the resistor pulls the drain of the transistor to VDD and when the FET is turned on, the FET pulls the output to ground, thus creating an effective resistor divider. The resistors in this divider must be chosen to make sure that VOL is below its maximum value. To choose the proper pullup resistor, there are three key specifications to keep in mind: the pullup voltage (VPU), the recommended maximum RESET pin current (IRST), and VOL. The maximum VOL is 0.3 V, meaning that the effective resistor divider created must be able to bring the voltage on the reset pin below 0.3 V with IRST kept below 2 mA for VDD ≥ 3 V and 500 μA for VDD = 1.5 V. For this example, with a VPU =VDD = 1.5 V, a resistor must be chosen to keep IRST below 500 μA because this value is the maximum consumption current allowed. To make sure this specification is met, a pullup resistor value of 10 kΩ was selected, which sinks a maximum of 180 μA when RESET is asserted.TPS35RESETOLPURESETRSTOLOLRSTDDDDPUDDRSTRESET
Open-Drain RESET Configuration
Open-Drain RESET Configuration
Open-Drain RESET ConfigurationRESET
Power Supply Recommendations
This device is designed to operate from
an input supply with a voltage range between 1.04 V and 6 V. An input supply capacitor is
not required for this device; however, if the input supply is noisy, then good analog
practice is to place a 0.1-µF capacitor between the VDD pin and the GND pin.
Power Supply Recommendations
This device is designed to operate from
an input supply with a voltage range between 1.04 V and 6 V. An input supply capacitor is
not required for this device; however, if the input supply is noisy, then good analog
practice is to place a 0.1-µF capacitor between the VDD pin and the GND pin.
This device is designed to operate from
an input supply with a voltage range between 1.04 V and 6 V. An input supply capacitor is
not required for this device; however, if the input supply is noisy, then good analog
practice is to place a 0.1-µF capacitor between the VDD pin and the GND pin.
This device is designed to operate from
an input supply with a voltage range between 1.04 V and 6 V. An input supply capacitor is
not required for this device; however, if the input supply is noisy, then good analog
practice is to place a 0.1-µF capacitor between the VDD pin and the GND pin.
Layout
Layout Guidelines
Make sure that the connection to the VDD pin is
low impedance. Good analog design practice recommends placing a 0.1-µF ceramic
capacitor as near as possible to the VDD pin. If a capacitor is not connected to the
CRST pin, then minimize parasitic capacitance on this pin so the
RESET
delay time is not adversely affected.
Make sure that the connection
to the VDD pin is low impedance. Good analog design practice is to place a
0.1-µF ceramic capacitor as near as possible to the VDD pin.
Place CCRST
capacitor as close as possible to the CRST pin.
Place CCWD
capacitor as close as possible to the CWD pin.
Place the pullup resistor on
the
RESET
pin as close to the pin as
possible.
Layout Example
Typical
Layout for the Pinout C of TPS35
Layout
Layout Guidelines
Make sure that the connection to the VDD pin is
low impedance. Good analog design practice recommends placing a 0.1-µF ceramic
capacitor as near as possible to the VDD pin. If a capacitor is not connected to the
CRST pin, then minimize parasitic capacitance on this pin so the
RESET
delay time is not adversely affected.
Make sure that the connection
to the VDD pin is low impedance. Good analog design practice is to place a
0.1-µF ceramic capacitor as near as possible to the VDD pin.
Place CCRST
capacitor as close as possible to the CRST pin.
Place CCWD
capacitor as close as possible to the CWD pin.
Place the pullup resistor on
the
RESET
pin as close to the pin as
possible.
Layout Guidelines
Make sure that the connection to the VDD pin is
low impedance. Good analog design practice recommends placing a 0.1-µF ceramic
capacitor as near as possible to the VDD pin. If a capacitor is not connected to the
CRST pin, then minimize parasitic capacitance on this pin so the
RESET
delay time is not adversely affected.
Make sure that the connection
to the VDD pin is low impedance. Good analog design practice is to place a
0.1-µF ceramic capacitor as near as possible to the VDD pin.
Place CCRST
capacitor as close as possible to the CRST pin.
Place CCWD
capacitor as close as possible to the CWD pin.
Place the pullup resistor on
the
RESET
pin as close to the pin as
possible.
Make sure that the connection to the VDD pin is
low impedance. Good analog design practice recommends placing a 0.1-µF ceramic
capacitor as near as possible to the VDD pin. If a capacitor is not connected to the
CRST pin, then minimize parasitic capacitance on this pin so the
RESET
delay time is not adversely affected.
Make sure that the connection
to the VDD pin is low impedance. Good analog design practice is to place a
0.1-µF ceramic capacitor as near as possible to the VDD pin.
Place CCRST
capacitor as close as possible to the CRST pin.
Place CCWD
capacitor as close as possible to the CWD pin.
Place the pullup resistor on
the
RESET
pin as close to the pin as
possible.
Make sure that the connection to the VDD pin is
low impedance. Good analog design practice recommends placing a 0.1-µF ceramic
capacitor as near as possible to the VDD pin. If a capacitor is not connected to the
CRST pin, then minimize parasitic capacitance on this pin so the
RESET
delay time is not adversely affected.
Make sure that the connection
to the VDD pin is low impedance. Good analog design practice is to place a
0.1-µF ceramic capacitor as near as possible to the VDD pin.
Place CCRST
capacitor as close as possible to the CRST pin.
Place CCWD
capacitor as close as possible to the CWD pin.
Place the pullup resistor on
the
RESET
pin as close to the pin as
possible.
RESET
RESET
Make sure that the connection
to the VDD pin is low impedance. Good analog design practice is to place a
0.1-µF ceramic capacitor as near as possible to the VDD pin.
Place CCRST
capacitor as close as possible to the CRST pin.
Place CCWD
capacitor as close as possible to the CWD pin.
Place the pullup resistor on
the
RESET
pin as close to the pin as
possible.
Make sure that the connection
to the VDD pin is low impedance. Good analog design practice is to place a
0.1-µF ceramic capacitor as near as possible to the VDD pin.Place CCRST
capacitor as close as possible to the CRST pin.CRSTPlace CCWD
capacitor as close as possible to the CWD pin.CWDPlace the pullup resistor on
the
RESET
pin as close to the pin as
possible.
RESET
RESET
Layout Example
Typical
Layout for the Pinout C of TPS35
Layout Example
Typical
Layout for the Pinout C of TPS35
Typical
Layout for the Pinout C of TPS35
Typical
Layout for the Pinout C of TPS35
Typical
Layout for the Pinout C of TPS35
TPS35
Device and Documentation Support
Receiving Notification of Documentation Updates
To receive notification of
documentation updates, navigate to the device product folder on ti.com. Click on
Notifications to register and receive a weekly digest of any product
information that has changed. For change details, review the revision history
included in any revised document.
Support Resources
TI E2E support forums
are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick
design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute
TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use.
Trademarks
Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
Device and Documentation Support
Receiving Notification of Documentation Updates
To receive notification of
documentation updates, navigate to the device product folder on ti.com. Click on
Notifications to register and receive a weekly digest of any product
information that has changed. For change details, review the revision history
included in any revised document.
Receiving Notification of Documentation Updates
To receive notification of
documentation updates, navigate to the device product folder on ti.com. Click on
Notifications to register and receive a weekly digest of any product
information that has changed. For change details, review the revision history
included in any revised document.
To receive notification of
documentation updates, navigate to the device product folder on ti.com. Click on
Notifications to register and receive a weekly digest of any product
information that has changed. For change details, review the revision history
included in any revised document.
To receive notification of
documentation updates, navigate to the device product folder on ti.com. Click on
Notifications to register and receive a weekly digest of any product
information that has changed. For change details, review the revision history
included in any revised document.ti.comNotifications
Support Resources
TI E2E support forums
are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick
design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute
TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use.
Support Resources
TI E2E support forums
are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick
design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute
TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use.
TI E2E support forums
are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick
design help you need.
TI E2E support forumsTI E2ELinked content is provided "AS IS" by the respective contributors. They do not constitute
TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use.Terms of Use
Trademarks
Trademarks
Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
TI Glossary
TI GlossaryThis glossary lists and explains terms, acronyms, and definitions.
Revision History
yes
June 2023
December 2023
*
A
Revision History
yes
June 2023
December 2023
*
A
yes
June 2023
December 2023
*
A
yesJune 2023December 2023*A
Mechanical, Packaging, and Orderable Information
The following pages include
mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to
change without notice and revision of this document. For browser-based versions
of this data sheet, refer to the left-hand navigation.
Mechanical, Packaging, and Orderable Information
The following pages include
mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to
change without notice and revision of this document. For browser-based versions
of this data sheet, refer to the left-hand navigation.
The following pages include
mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to
change without notice and revision of this document. For browser-based versions
of this data sheet, refer to the left-hand navigation.
The following pages include
mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to
change without notice and revision of this document. For browser-based versions
of this data sheet, refer to the left-hand navigation.
The following pages include
mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to
change without notice and revision of this document. For browser-based versions
of this data sheet, refer to the left-hand navigation.
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING
DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION
OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER
RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES,
EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT
OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers
designing with TI products. You are solely responsible for (1) selecting
the appropriate TI products for your application, (2) designing,
validating and testing your application, and (3) ensuring your
application meets applicable standards, and any other safety, security, regulatory
or other requirements.
These resources are subject to change without
notice. TI grants you permission to use these resources only for
development of an application that uses the TI products described in the
resource. Other reproduction and display of these resources is
prohibited. No license is granted to any other TI intellectual property
right or to any third party intellectual property right. TI disclaims
responsibility for, and you will fully indemnify TI and its
representatives against, any claims, damages, costs, losses, and
liabilities arising out of your use of these resources.
TI’s products are provided subject to
TI’s Terms of Sale or other applicable
terms available either on ti.com or provided in conjunction with such
TI products. TI’s provision of these resources does not expand or
otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address:
Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING
DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION
OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER
RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES,
EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT
OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers
designing with TI products. You are solely responsible for (1) selecting
the appropriate TI products for your application, (2) designing,
validating and testing your application, and (3) ensuring your
application meets applicable standards, and any other safety, security, regulatory
or other requirements.
These resources are subject to change without
notice. TI grants you permission to use these resources only for
development of an application that uses the TI products described in the
resource. Other reproduction and display of these resources is
prohibited. No license is granted to any other TI intellectual property
right or to any third party intellectual property right. TI disclaims
responsibility for, and you will fully indemnify TI and its
representatives against, any claims, damages, costs, losses, and
liabilities arising out of your use of these resources.
TI’s products are provided subject to
TI’s Terms of Sale or other applicable
terms available either on ti.com or provided in conjunction with such
TI products. TI’s provision of these resources does not expand or
otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address:
Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING
DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION
OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER
RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES,
EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT
OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers
designing with TI products. You are solely responsible for (1) selecting
the appropriate TI products for your application, (2) designing,
validating and testing your application, and (3) ensuring your
application meets applicable standards, and any other safety, security, regulatory
or other requirements.
These resources are subject to change without
notice. TI grants you permission to use these resources only for
development of an application that uses the TI products described in the
resource. Other reproduction and display of these resources is
prohibited. No license is granted to any other TI intellectual property
right or to any third party intellectual property right. TI disclaims
responsibility for, and you will fully indemnify TI and its
representatives against, any claims, damages, costs, losses, and
liabilities arising out of your use of these resources.
TI’s products are provided subject to
TI’s Terms of Sale or other applicable
terms available either on ti.com or provided in conjunction with such
TI products. TI’s provision of these resources does not expand or
otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING
DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION
OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER
RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES,
EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT
OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers
designing with TI products. You are solely responsible for (1) selecting
the appropriate TI products for your application, (2) designing,
validating and testing your application, and (3) ensuring your
application meets applicable standards, and any other safety, security, regulatory
or other requirements.
These resources are subject to change without
notice. TI grants you permission to use these resources only for
development of an application that uses the TI products described in the
resource. Other reproduction and display of these resources is
prohibited. No license is granted to any other TI intellectual property
right or to any third party intellectual property right. TI disclaims
responsibility for, and you will fully indemnify TI and its
representatives against, any claims, damages, costs, losses, and
liabilities arising out of your use of these resources.
TI’s products are provided subject to
TI’s Terms of Sale or other applicable
terms available either on ti.com or provided in conjunction with such
TI products. TI’s provision of these resources does not expand or
otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING
DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION
OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER
RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES,
EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT
OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers
designing with TI products. You are solely responsible for (1) selecting
the appropriate TI products for your application, (2) designing,
validating and testing your application, and (3) ensuring your
application meets applicable standards, and any other safety, security, regulatory
or other requirements.
These resources are subject to change without
notice. TI grants you permission to use these resources only for
development of an application that uses the TI products described in the
resource. Other reproduction and display of these resources is
prohibited. No license is granted to any other TI intellectual property
right or to any third party intellectual property right. TI disclaims
responsibility for, and you will fully indemnify TI and its
representatives against, any claims, damages, costs, losses, and
liabilities arising out of your use of these resources.
TI’s products are provided subject to
TI’s Terms of Sale or other applicable
terms available either on ti.com or provided in conjunction with such
TI products. TI’s provision of these resources does not expand or
otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING
DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION
OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER
RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES,
EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT
OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING
DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION
OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER
RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES,
EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT
OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers
designing with TI products. You are solely responsible for (1) selecting
the appropriate TI products for your application, (2) designing,
validating and testing your application, and (3) ensuring your
application meets applicable standards, and any other safety, security, regulatory
or other requirements.
These resources are intended for skilled developers
designing with TI products. You are solely responsible for (1) selecting
the appropriate TI products for your application, (2) designing,
validating and testing your application, and (3) ensuring your
application meets applicable standards, and any other safety, security, regulatory
or other requirements.
These resources are subject to change without
notice. TI grants you permission to use these resources only for
development of an application that uses the TI products described in the
resource. Other reproduction and display of these resources is
prohibited. No license is granted to any other TI intellectual property
right or to any third party intellectual property right. TI disclaims
responsibility for, and you will fully indemnify TI and its
representatives against, any claims, damages, costs, losses, and
liabilities arising out of your use of these resources.
These resources are subject to change without
notice. TI grants you permission to use these resources only for
development of an application that uses the TI products described in the
resource. Other reproduction and display of these resources is
prohibited. No license is granted to any other TI intellectual property
right or to any third party intellectual property right. TI disclaims
responsibility for, and you will fully indemnify TI and its
representatives against, any claims, damages, costs, losses, and
liabilities arising out of your use of these resources.
TI’s products are provided subject to
TI’s Terms of Sale or other applicable
terms available either on ti.com or provided in conjunction with such
TI products. TI’s provision of these resources does not expand or
otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI’s products are provided subject to
TI’s Terms of Sale or other applicable
terms available either on ti.com or provided in conjunction with such
TI products. TI’s provision of these resources does not expand or
otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.TI’s Terms of Saleti.com
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
IMPORTANT NOTICE
Mailing Address:
Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
Mailing Address:
Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
Mailing Address:
Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
Mailing Address:
Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
Mailing Address:
Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
Copyright © 2023, Texas Instruments Incorporated for the
tD value computation. For a capacitor based tD delay
option, the RESET is asserted for tSTRT + 2 msec time if the CRST pin is
open.
Device pinout options A to C and J, K offer only RESET output. In these devices the internal RESET output from supervisor and WDO output from watchdog timer are ANDed together to drive the external RESET output.
The supervisor offers wide range of fixed
monitoring thresholds (VIT-) from 1.05 V to 5.40 V in steps of 50 mV. The
device asserts the RESET output when the VDD signal falls below VIT-
threshold. The device offers hysteresis functionality for voltage supervision. This
makes sure the supply has recovered above the monitoring threshold before the RESET
output is deasserted. The TPS35 typical voltage hysteresis
(VHYS) is 5%. Along with the voltage hysteresis, the device keeps the
RESET output asserted for time duration tD after the supply has risen
above VIT+. The RESET output assert duration changes from tD
to tSTRT + tD if the VDD signal is ramping from voltage <
VPOR. The tD time duration can be programmable using an
external capacitor or fixed time options offered by the device.
The typical timing behavior for a voltage
supervisor and the RESET output is showcased in Figure 7-7. The voltage
supervisor monitoring output has higher priority over watchdog functionality. If the
device voltage supervisor output is asserted, the watchdog functionality is disabled
including WDO assert control. The device resumes watchdog related functionality only
after the supply is stable and the tD time duration has elapsed.
Figure 7-7 Voltage Supervisor Timing Diagram