SLVSGE9A november   2022  – april 2023 TPS36-Q1

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Device Comparison
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Switching Characteristics
    8. 7.8 Timing Diagrams
    9. 7.9 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagrams
    3. 8.3 Feature Description
      1. 8.3.1 Voltage Supervisor
      2. 8.3.2 Window Watchdog Timer
        1. 8.3.2.1 tWC (Close Window) Timer
        2. 8.3.2.2 tWO (Open Window) Timer
        3. 8.3.2.3 Watchdog Enable Disable Operation
        4. 8.3.2.4 tSD Watchdog Start Up Delay
        5. 8.3.2.5 SET Pin Behavior
      3. 8.3.3 Manual RESET
      4. 8.3.4 RESET and WDO Output
    4. 8.4 Device Functional Modes
  9. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 CRST Delay
        1. 9.1.1.1 Factory-Programmed Reset Delay Timing
        2. 9.1.1.2 Adjustable Capacitor Timing
      2. 9.1.2 Watchdog Window Functionality
        1. 9.1.2.1 Factory-Programmed watchdog Timing
        2. 9.1.2.2 Adjustable Capacitor Timing
    2. 9.2 Typical Applications
      1. 9.2.1 Design 1: Monitoring Microcontroller Supply and Watchdog During Operational and Sleep Modes
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Setting Voltage Threshold
          2. 9.2.1.2.2 Determining Window Timings During Operation and Sleep Modes
          3. 9.2.1.2.3 Meeting the Minimum Reset Delay
          4. 9.2.1.2.4 Setting the Watchdog Window
          5. 9.2.1.2.5 Calculating the RESET Pullup Resistor
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  10. 10Device and Documentation Support
    1. 10.1 Receiving Notification of Documentation Updates
    2. 10.2 Support Resources
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  11. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.1 Absolute Maximum Ratings

over operating free-air temperature range, unless otherwise noted(1)
MIN MAX UNIT
Voltage VDD –0.3 6.5 V
Voltage CWD, CRST, WD–EN, SETx, WDI,  MR (2),  RESET (Push Pull), WDO (Push Pull) –0.3 VDD+0.3 (3) V
 RESET (Open Drain), WDO (Open Drain) –0.3 6.5
Current RESET, WDO pin –20 20 mA
Temperature (4) Operating ambient temperature, TA –40 125 ℃
Temperature Storage, Tstg –65 150
(1) Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If the logic signal driving MR is less than VDD, then additional current flows into VDD and out of MR. 
(3) The absolute maximum rating is (VDD + 0.3) V or 6.5 V, whichever is smaller
(4) As a result of the low dissipated power in this device, it is assumed that TJ = TA.