SNVSAZ4A February   2021  – March 2021 TPS541620

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Fixed-Frequency, Internally Compensated Advanced-Current-Mode Control
      2. 7.3.2  Enable and UVLO
      3. 7.3.3  Internal LDO
      4. 7.3.4  Pre-biased Output Start-up
      5. 7.3.5  Current Sharing
      6. 7.3.6  Frequency Selection and Minimum On-Time and Off-Time
      7. 7.3.7  Ramp Compensation Selection
      8. 7.3.8  Soft Start
      9. 7.3.9  Remote Sense Function
      10. 7.3.10 Adjustable Output Voltage
      11. 7.3.11 Power Good
      12. 7.3.12 Overcurrent Protection
      13. 7.3.13 Overvoltage and Undervoltage Protection
      14. 7.3.14 Overtemperature Protection
      15. 7.3.15 Frequency Synchronization
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation Mode
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application - Dual Independent Outputs
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1  Switching Frequency
        2. 8.2.2.2  Output Inductor Selection
        3. 8.2.2.3  Output Capacitor
        4. 8.2.2.4  Input Capacitor
        5. 8.2.2.5  Output Voltage Resistors Selection
        6. 8.2.2.6  Adjustable Undervoltage Lockout
        7. 8.2.2.7  Bootstrap Capacitor Selection
        8. 8.2.2.8  BP5 Capacitor Selection
        9. 8.2.2.9  PGOOD Pullup Resistor
        10. 8.2.2.10 Current Limit
        11. 8.2.2.11 Soft-Start Time Selection
        12. 8.2.2.12 MODE1 and MODE2 Pins
      3. 8.2.3 Application Curves
      4. 8.2.4 Typical Application - 2-Phase Operation
        1. 8.2.4.1 Design Requirements
        2. 8.2.4.2 Detailed Design Procedure
          1. 8.2.4.2.1  Switching Frequency
          2. 8.2.4.2.2  Output Inductor Selection
          3. 8.2.4.2.3  Output Capacitor
          4. 8.2.4.2.4  Input Capacitor
          5. 8.2.4.2.5  Output Voltage Resistors Selection
          6. 8.2.4.2.6  Adjustable Undervoltage Lockout
          7. 8.2.4.2.7  Bootstrap Capacitor Selection
          8. 8.2.4.2.8  BP5 Capacitor Selection
          9. 8.2.4.2.9  PGOOD Pullup Resistor
          10. 8.2.4.2.10 Current Limit
          11. 8.2.4.2.11 Soft-Start Time Selection
          12. 8.2.4.2.12 MODE1 Pin
        3. 8.2.4.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
      1. 10.2.1 Thermal Performance
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.3.13 Overvoltage and Undervoltage Protection

The device includes both output overvoltage protection and output undervoltage protection capability. The device compares the FB voltage to internal preset voltages. If the FB voltage with respect to GOSNS voltage rises above the output overvoltage protection threshold after a 10-μs delay, the device terminates normal switching and enters continuous hiccup process. The device waits for 7 × Tss and tries to restart. Overvoltage protection is enabled both during and after soft start is completed.

If the FB pin voltage with respect to GOSNS falls below the undervoltage protection threshold, the device enters hiccup after 7 × Tss of wait time. Undervoltage protection is enabled after soft start is completed.