SLVSEW2A September   2020  – August 2021 TPS54618C-Q1

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Fixed Frequency PWM Control
      2. 7.3.2  Slope Compensation and Output Current
      3. 7.3.3  Bootstrap Voltage (Boot) and Low Dropout Operation
      4. 7.3.4  Error Amplifier
      5. 7.3.5  Voltage Reference
      6. 7.3.6  Adjusting the Output Voltage
      7. 7.3.7  Enable and Adjusting Undervoltage Lockout
      8. 7.3.8  Soft-Start Pin
      9. 7.3.9  Sequencing
      10. 7.3.10 Constant Switching Frequency and Timing Resistor (RT/CLK Pin)
      11. 7.3.11 Overcurrent Protection
      12. 7.3.12 Frequency Shift
      13. 7.3.13 Reverse Overcurrent Protection
      14. 7.3.14 Synchronize Using the RT/CLK Pin
      15. 7.3.15 Power Good (PWRGD Pin)
      16. 7.3.16 Overvoltage Transient Protection
      17. 7.3.17 Thermal Shutdown
    4. 7.4 Device Functional Modes
      1. 7.4.1 Simple Small Signal Model for Peak Current Mode Control
      2. 7.4.2 Small Signal Model for Frequency Compensation
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Step One: Select the Switching Frequency
        2. 8.2.2.2 Step Two: Select the Output Inductor
        3. 8.2.2.3 Step Three: Choose the Output Capacitor
        4. 8.2.2.4 Step Four: Select the Input Capacitor
        5. 8.2.2.5 Step Five: Choose the Soft-Start Capacitor
        6. 8.2.2.6 Step Six: Select the Bootstrap Capacitor
        7. 8.2.2.7 Step Eight: Select Output Voltage and Feedback Resistors
          1. 8.2.2.7.1 Output Voltage Limitations
        8. 8.2.2.8 Step Nine: Select Loop Compensation Components
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
    3. 10.3 Power Dissipation Estimate
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Developmental Support
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.6 Timing Requirements

MIN NOM MAX UNIT
TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK PIN)
Switching frequency range using RT mode 200 2000 kHz
Switching frequency Rt = 400 kΩ 400 500 600 kHz
Switching frequency range using CLK mode 300 2000 kHz
Minimum CLK pulse width 75 ns
RT/CLK voltage R(RT/CLK) = 400 kΩ 0.5 V
RT/CLK high threshold 1.6 2.2 V
RT/CLK low threshold 0.4 0.6 V
RT/CLK falling edge to PH rising edge delay Measure at 500 kHz with RT resistor in series 90 ns
PLL lock in time Measure at 500 kHz 42 μs
PH (PH PIN)
Minimum ON-time Measured at 50% points on PH, IOUT = 3 A 75 ns
Measured at 50% points on PH, VIN = 6 V,
IOUT = 0 A		 120
Minimum OFF-time Prior to skipping off pulses, BOOT-PH = 2.95 V,
IOUT = 3 A		 60 ns
Rise time VIN = 6 V, 6 A 2.25 V/ns
Fall time VIN = 6 V, 6 A 2