SLVSDC9B November   2016  – November 2019 TPS54824

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
    1.     Simplified Schematic
  3. 3 Description
    1.     Efficiency
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Timing Requirements
    8. 6.8 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Fixed Frequency PWM Control
      2. 7.3.2  Continuous Conduction Mode Operation (CCM)
      3. 7.3.3  VIN Pins and VIN UVLO
      4. 7.3.4  Voltage Reference and Adjusting the Output Voltage
      5. 7.3.5  Error Amplifier
      6. 7.3.6  Enable and Adjustable UVLO
      7. 7.3.7  Soft Start and Tracking
      8. 7.3.8  Safe Start-up into Pre-Biased Outputs
      9. 7.3.9  Power Good
      10. 7.3.10 Sequencing (SS/TRK)
      11. 7.3.11 Adjustable Switching Frequency (RT Mode)
      12. 7.3.12 Synchronization (CLK Mode)
      13. 7.3.13 Bootstrap Voltage and 100% Duty Cycle Operation (BOOT)
      14. 7.3.14 Output Overvoltage Protection (OVP)
      15. 7.3.15 Overcurrent Protection
        1. 7.3.15.1 High-side MOSFET Overcurrent Protection
        2. 7.3.15.2 Low-side MOSFET Overcurrent Protection
    4. 7.4 Device Functional Modes
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1  Switching Frequency
        2. 8.2.2.2  Output Inductor Selection
        3. 8.2.2.3  Output Capacitor
        4. 8.2.2.4  Input Capacitor
        5. 8.2.2.5  Output Voltage Resistors Selection
        6. 8.2.2.6  Soft-start Capacitor Selection
        7. 8.2.2.7  Undervoltage Lockout Set Point
        8. 8.2.2.8  Bootstrap Capacitor Selection
        9. 8.2.2.9  PGOOD Pull-up Resistor
        10. 8.2.2.10 Compensation
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
    3. 10.3 Alternate Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Receiving Notification of Documentation Updates
    2. 11.2 Community Resources
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.5 Electrical Characteristics

TJ = -40°C to 150°C, VIN = 4.5 V to 17 V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
INPUT VOLTAGE
UVLO_rise VIN under-voltage lockout V(VIN) rising 4.1 4.3 V
UVLO_fall V(VIN) falling 3.7 3.9 V
UVLO_hys Hysteresis VIN voltage 0.2 V
Ivin Operating non-switching supply current V(EN) = 5 V, V(FB) = 1.5 V 580 800 µA
Ivin_sdn Shutdown supply current V(EN) = 0 V 3 11 µA
ENABLE
Ven_rise EN threshold V(EN) rising 1.20 1.26 V
Ven_fall V(EN) falling 1.1 1.15 V
Ven_hys EN pin threshold voltage hysteresis 50 mV
Ip EN pin sourcing current V(EN) = 1.1V 1.2 µA
Iph EN pin sourcing current V(EN) = 1.3V 4.8 µA
Ih EN pin hysteresis current 3.6 µA
FB
VFB Regulated FB voltage TJ = 25°C 596 600 604 mV
595 600 605 mV
ERROR AMPLIFIER
gmea Error Amplifier Transconductance (gm) –2 µA < I(COMP) < 2 µA, V(COMP) = 1 V 1100 µA/V
Error Amplifier DC gain 80 dB
Icomp_src Error Amplifier source current V(FB) = 0 V 100 µA
Icomp_snk Error Amplifier sink current V(FB) = 2 V -100 µA
gmps Power Stage Transconductance 16 A/V
SOFT-START
Iss Soft-start current 5 µA
V(SS/TRK) to V(FB) matching V(SS/TRK) = 0.4 V 25 mV
MOSFET
Rds(on)_h High-side switch resistance TA = 25°C, V(VIN) = 12 V 14.1 mΩ
TA = 25°C, V(VIN) = 4.5 V, V(BOOT-SW) = 4.5 V 15.9 mΩ
Rds(on)_l Low-side switch resistance TA = 25°C, V(VIN) = 12 V 6.1 mΩ
TA = 25°C, V(VIN) = 4.5 V 6.9 mΩ
BOOT UVLO Falling 2.2 2.6 V
CURRENT LIMIT
Ioc_HS_pk High-side peak current limit 10.8 12.9 15 A
Ioc_LS_snk Low-side sinking current limit –3.4 A
Ioc_LS_src Low-side sourcing current limit 9.3 11.4 13.6 A
RT/CLK
VIH Logic high input voltage 2 V
VIL Logic low input voltage 0.8 V
PGOOD
Power good threshold V(FB) rising (fault) 108%
V(FB) falling (good) 106%
V(FB) rising (good) 91%
V(FB) falling (fault) 89%
Ipg_lkg Leakage current when pulled high V(PGOOD) = 5 V 5 nA
Vpg_low PGOOD voltage when pulled low I(PGOOD) = 2 mA 0.3 V
Minimum VIN for valid output V(PGOOD) < 0.5 V, I(PGOOD) = 4 mA 0.7 1 V
Thermal protection
TTRIP Thermal protection trip point Temperature Rising 170 °C
THYST Thermal protection hysteresis 15 °C